Wiring RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ABS Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 64, PDF Size: 0.2 MB
Page 2 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
38C
38C - 2V2 MR-372-J84-38C000$066_eng.mif
138C
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper version.
Type of diagnostic tools
–CLIP
Special tooling required
3. RECAP
Procedure
To perform fault finding on the vehicle's computers, switch on the ignition in fault finding mode.
Proceed as follows:
–vehicle's card in reader;
–press and hold the Start button (longer than 5 seconds) with start-up conditions not present,
–connect the diagnostic tool and perform the required operations.
To cut off + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–Ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the instrument
panel have gone out. Vehicle(s): Mégane II, Scénic II
Function concerned: ABSName of computer: BOSCH ABS 8.0
Vdiag No: 0C, 0D, 0E, 0F
Special tooling required
Multimeter
Elé. 1681Universal bornier
Note:
The left and right-hand discharge bulb computers are supplied when the dipped headlights are lit. Therefore fault
finding can only be carried out on them after the ignition has been switched on in fault finding mode (forced + after
ignition feed) and the dipped headlights have been switched on.
ABS8.0_V0C_PRELI /ABS8.0_V0D_PRELI /ABS8.0_V0E_PRELI/ABS8.0_V0F_PRELI ABS 8.0X84 4.0
MR-372-J84-38C000$066_eng.mif
Page 5 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
38C
38C - 5V2 MR-372-J84-38C000$066_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
4. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.
ABS 8.0X84 4.0
Page 12 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 12V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
DF001
PRESENT
OR
STOREDCOMPUTER FEED
1.DEF : Below minimum threshold
2.DEF : Above maximum threshold
3.DEF : Abnormal voltage
NOTESSpecial notes:
The fault is declared present during a road test at a speed of > 6 mph (10 km/h). The
computer signals an external supply fault.
Conditions for applying the fault finding procedure to stored faults:
Apply the fault finding procedure whether the fault is present or stored.
Check the connections and the condition of the battery terminals.
Check the condition and position of the ABS fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check the 25A fuse F13 on the UPC and the correct locking of the grey 4-track PPHI connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the 26-track connector of the ABS computer.
Check the ABS earths on tracks 1 and 4 (attached under the ABS unit) and carry out an inspection of the entire
ABS wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ Before ignition present
on the tracks) and between the UCH and track 18 of the computer (+ After ignition present on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out another check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF001 /ABS8.0_V0D_DF001/ABS8.0_V0E_DF001/ABS8.0_V0F_DF001 ABS 8.0X84 4.0
MR-372-J84-38C000$396_eng.mif
Page 13 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 13V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D
DF006
PRESENT
OR
STOREDLEFT-HAND FRONT WHEEL SPEED SENSOR CIRCUIT
CO.0 : Open circuit or short circuit to earth
1.DEF : Magnetic/mechanical target fault
Vdiag No.: 0C, 0D
NOTESSpecial notes:
The wheel speed sensors are fed with + 12 V APC but this feed cannot be measured
on Vdiag 0C and 0D (feed cut off when the sensor is faulty).
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
NOTESNone
Check the connection and the condition of the sensor connectors.
Swap the two front wheel speed sensors over.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
If the fault initially declared DF006 "Front left-hand wheel speed sensor circuit" becomes DF026 "Front
right-hand wheel speed sensor circuit", replace the wheel speed sensor.
If the fault remains on the same side, the wiring between the computer and the sensor is faulty.
Check the connection and the condition of the computer connectors. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the 2 tracks Track 5 computer connector
Sensor connector the other track Track 16 computer connector
Also check the insulation between these two connections.
Repair if necessary.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF006 /ABS8.0_V0D_DF006ABS 8.0X84 4.0
Page 15 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 15V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0E, 0F
DF006
PRESENT
OR
STOREDLEFT-HAND FRONT WHEEL SPEED SENSOR CIRCUIT
CO.0 : Open circuit or short circuit to earth
1.DEF : Magnetic/mechanical target fault
2.DEF : Open circuit or short circuit
Vdiag No.: 0E, 0F
NOTESNone
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
2.DEF
NOTESSpecial notes:
You must use command AC013 once only.
Check the connection and the condition of the sensor connectors.
Disconnect the sensor, run command AC013 Test wheel speed sensor supply and check that voltage pulses
of about 12 V are detected by a multimeter at the sensor connector terminals on the computer side.
Have you found voltage pulses?
YES
The wiring between the computer and the sensor, as well the supply via the computer,
is OK. Left-hand front wheel speed sensor fault - replace the sensor.
Check the connection and the condition of the computer connectors. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the
2 tracksTrack 5 computer connector
Sensor connector the other track Track 16 computer connector
Also check the insulation between these two connections.
If all the checks are in order, contact Techline.
NO
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0E_DF006/ ABS8.0_V0F_DF006ABS 8.0X84 4.0
Page 17 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 17V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D
DF007
PRESENT
OR
STOREDLEFT-HAND REAR WHEEL SPEED SENSOR CIRCUIT
CO.0 : Open circuit or short circuit to earth
1.DEF : Magnetic/mechanical target fault
Vdiag No.: 0C, 0D
NOTESSpecial notes:
The wheel speed sensors are fed with + 12 V APC but this feed cannot be measured
on Vdiag 0C and 0D (feed cut off when the sensor is faulty).
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
NOTESNone
Check the connection and the condition of the sensor connectors.
Swap the two rear wheel speed sensors over.
Clear the computer's fault memory.
Carry out a road test followed by another check with the diagnostic tool.
If the fault initially declared DF007 "Rear left-hand wheel speed sensor circuit" becomes DF027 "Rear
right-hand wheel speed sensor circuit", replace the wheel speed sensor.
If the fault remains on the same side, the wiring between the computer and the sensor is faulty.
Check the connection and the condition of the computer connectors. Repair if necessary.
Check the connections (Track 31 and 32) at the R2 black 52-track intermediate connection beneath the front
left-hand seat. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the 2 tracks Track 6 computer connector
Sensor connector the other track Track 17 computer connector
Also check the insulation between these two connections.
If the connections are faulty, carry out the following checks:
Check the insulation, continuity and absence of interference resistance between:
Computer connector track 6 Track 32 on the intermediate connector
Computer connector track 17 Track 31 on the intermediate connector
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF007 /ABS8.0_V0D_DF007ABS 8.0X84 4.0
Page 18 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 18V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D
DF007
CONTINUED
Vdiag No.: 0C, 0D
Also check the insulation between the following two connections. Repair or replace the wiring if necessary.
Check the insulation, continuity and absence of interference resistance between:
Sensor connector one of the 2 tracks Track 31 on the intermediate connector
Sensor connector the other track Track 32 on the intermediate connector
Also check the insulation between these two connections. Repair or replace the wiring if necessary.
1.DEF
NOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
–Replace the rear left-hand "disc-hub-bearing" assembly (see MR364 or MR370 Mechanical, 33A, Rear axle
components, Bearing: Removal - Refitting) if the fault reappears.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS 8.0X84 4.0
Page 19 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 19V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0E, 0F
DF007
PRESENT
OR
STOREDLEFT-HAND REAR WHEEL SPEED SENSOR CIRCUIT
CO.0 : Open circuit or short circuit to earth
1.DEF : Magnetic/mechanical target fault
2.DEF : Open circuit or short circuit
Vdiag No.: 0E, 0F
NOTESNone
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
2.DEF
NOTESSpecial notes:
You must use command AC013 once only.
Check the connection and the condition of the sensor connectors.
Disconnect the sensor, use command AC013 "Test wheel speed sensor supply" and check that pulses of
voltage of about 12 V are detected by a multimeter at the sensor connector terminals on the computer side.
Have you found voltage pulses?
YES
The wiring between the computer and the sensor, as well the supply via the computer,
is OK. Rear left-hand wheel speed sensor fault - replace the sensor.
Check the connection and the condition of the computer connectors. Repair if necessary.
Check the connections (Track 31 and 32) at the R2 black 52-track intermediate
connection beneath the front left-hand seat. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the
2 tracksTrack 6 computer connector
Sensor connector the other track Track 17 computer connector
NO
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0E_DF007/ ABS8.0_V0F_DF007ABS 8.0X84 4.0
Page 21 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 21V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF017
PRESENT
OR
STOREDCOMPUTER
1.DEF : Feed fault or internal electronic fault
2.DEF : Programming / initialisation invalid
NOTESSpecial notes:
The voltage displayed in the parameter (PR005) is the + after ignition feed voltage of
the computer and not the hydraulic unit power feed.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Check the connections and the condition of the battery terminals.
Check the condition and position of the ABS fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check the 25A fuse F13 on the UPC and the correct locking of the grey 4-track PPHI connector (Vdiag 44) or
test the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the 26-track connector of the ABS computer.
Check the ABS earths on tracks 1 and 4 (attached under the ABS unit) and carry out an inspection of the entire
ABS wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ Before ignition present
on the tracks) and between the UCH and track 18 of the computer (+ After ignition present on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out another check using the diagnostic tool.
If the fault is still present, contact the Techline.
2.DEF
NOTESSpecial notes:
No programming for PR020 Vehicle speed at initialisation.
ABS warning light flashing at 8 Hz outside fault finding
conditions.
Run command VP032 and select "Type 1" or "Type 2" according to the information supplied by the diagnostic tool.
Clear the computer fault memory, switch the ignition off and carry out a road test. If the fault is still present, contact
the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF017 /ABS8.0_V0D_DF017/ABS8.0_V0E_DF017/ABS8.0_V0F_DF017 ABS 8.0X84 4.0
Page 23 of 64
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 23V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D
DF026
PRESENT
OR
STOREDRIGHT-HAND FRONT WHEEL SPEED SENSOR CIRCUIT
CO.0 : Open circuit or short circuit to earth
1.DEF : Magnetic/mechanical target fault
Vdiag No.: 0C, 0D
NOTESSpecial notes:
The wheel speed sensors are fed with + 12 V APC but this feed cannot be measured
on Vdiag 0C and 0D (feed cut off when the sensor is faulty).
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
NOTESNone
Check the connection and the condition of the sensor connectors.
Swap the two front wheel speed sensors over.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
If the DF026 Front right-hand wheel speed sensor circuit fault initially declared changes to DF006 Front
left- hand wheel speed sensor circuit present, replace the wheel speed sensor.
If the fault remains on the same side, the wiring between the computer and the sensor is faulty.
Check the connection and the condition of the computer connectors. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the 2 tracks Track 9 computer connector
Sensor connector the other track Track 10 computer connector
Also check the insulation between these two connections.
Repair if necessary.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF026 /ABS8.0_V0D_DF026ABS 8.0X84 4.0