ignition RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ABS Workshop Manual

ANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
38C
38C - 2V2 MR-372-J84-38C000$066_eng.mif
138C
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper version.
Type of diagnostic tools
–CLIP
Special tooling required
3. RECAP
Procedure
To perform fault finding on the vehicle's computers, switch on the ignition in fault finding mode.
Proceed as follows:
–vehicle's card in reader;
–press and hold the Start button (longer than 5 seconds) with start-up conditions not present,
–connect the diagnostic tool and perform the required operations.
To cut off + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–Ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the instrument
panel have gone out. Vehicle(s): Mégane II, Scénic II
Function concerned: ABSName of computer: BOSCH ABS 8.0
Vdiag No: 0C, 0D, 0E, 0F
Special tooling required
Multimeter
Elé. 1681Universal bornier
Note:
The left and right-hand discharge bulb computers are supplied when the dipped headlights are lit. Therefore fault
finding can only be carried out on them after the ignition has been switched on in fault finding mode (forced + after
ignition feed) and the dipped headlights have been switched on.
ABS8.0_V0C_PRELI /ABS8.0_V0D_PRELI /ABS8.0_V0E_PRELI/ABS8.0_V0F_PRELI ABS 8.0X84 4.0
MR-372-J84-38C000$066_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
38C
38C - 3V2 MR-372-J84-38C000$066_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
Faults
Faults are declared as either present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but have not been diagnosed within the current context).
The present or stored status of faults should be taken into consideration when the diagnostic tool is switched on
after the + after ignition feed (without any system components being active).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the instructions in the Notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with the fault
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors for these lines (for oxidation, bent pins, etc.),
–the resistance of the component detected as faulty,
–the condition of the wires (melted or split insulation, wear).
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool because the
data is inconsistent. Therefore, this stage is used to:
–carry out fault finding on faults that do not have a fault display, and which may correspond to a customer
complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repairs.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the
corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
customer complaints.
A synopsis of the general procedure to follow is provided on the following page
in the form of a flow chart
ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Replacement of components
38C
38C - 9V2 MR-372-J84-38C000$198_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Replacement of components
Replacing the computer
When replacing the computer, apply the following procedure:
–switch off the ignition,
–replace the computer (see MR364 or MR370, Mechanical 38C, Anti-lock braking system, Hydraulic unit),
–enter the VIN using command VP001,
–configure the tachometric index using command VP007,
–enter the most recent After Sales operation date using command VP006;
–For Vdiag 0F: configure the vehicle parameters with command VP004 and configure the vehicle speed with
command VP032;
–perform a road test followed by a fault reading to confirm that the system is operating correctly.
ABS 8.0X84 4.0
MR-372-J84-38C000$198_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Configurations and programming38C
38C - 10V2 MR-372-J84-38C000$264_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Configurations and programming
Settings
VP001: Write VIN.
This command allows the vehicle identification number to be entered into the computer. Use this
command each time the computer is replaced. The VIN number (VF...) can be found on the
manufacturer's plate on the front right-hand door pillar and on the body panel under the left-hand side
of the windscreen.
VP004: Vehicle parameters.
This command is used to configure the engine type + braking definition + body type.
Select command VP004 on the diagnostic tool (it is imperative to check that the variants selected
correspond to the vehicle type).
VP006: Write date of the last After-Sales service.
Whenever the ABS system is worked on in the shop, the date must be entered.
Select command VP006 on the diagnostic tool.
Enter the operation date with the tool keyboard.
VP007: Tachometric index.
This command is used to program the computer memory with the index required to calculate vehicle
speed from the speed at which the wheels turn.
The BOSCH ABS 8.0 computer supplies the vehicle speed signal to all vehicle systems that use this
information (instrument panel, engine management, etc.). This vehicle speed signal replaces the one
supplied by the speed sensor located on the gearbox. The ABS computer calculates the vehicle speed
from the speed of the wheels and the circumference of the tyres fitted on the vehicle.
Note:
The vehicle speed is sent by wire (track 23) to the xenon bulb computer, radio and electric sunroof, and
via the multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists
of entering a number X using the VP007 "Tachometric index" command on the diagnostic tool.
Once the number has been entered using the VP007 command, delete the fault in the computer memory
and then switch off the ignition. Use the parameter PR030 to check that the index entered has been
stored correctly.
VP032: Vehicle speed at initialisation.
Vehicle speed transmitted via the multiplex network when the computer is initialised.
Select "Type 1" or "Type 2" according to the information supplied by the tool.
ABS 8.0X84 4.0
MR-372-J84-38C000$264_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 12V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
DF001
PRESENT
OR
STOREDCOMPUTER FEED
1.DEF : Below minimum threshold
2.DEF : Above maximum threshold
3.DEF : Abnormal voltage
NOTESSpecial notes:
The fault is declared present during a road test at a speed of > 6 mph (10 km/h). The
computer signals an external supply fault.
Conditions for applying the fault finding procedure to stored faults:
Apply the fault finding procedure whether the fault is present or stored.
Check the connections and the condition of the battery terminals.
Check the condition and position of the ABS fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check the 25A fuse F13 on the UPC and the correct locking of the grey 4-track PPHI connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the 26-track connector of the ABS computer.
Check the ABS earths on tracks 1 and 4 (attached under the ABS unit) and carry out an inspection of the entire
ABS wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ Before ignition present
on the tracks) and between the UCH and track 18 of the computer (+ After ignition present on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out another check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF001 /ABS8.0_V0D_DF001/ABS8.0_V0E_DF001/ABS8.0_V0F_DF001 ABS 8.0X84 4.0
MR-372-J84-38C000$396_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 14V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D
DF006
CONTINUED
Vdiag No.: 0C, 0D
1.DEF
NOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check the quality of the mounting of the wheel speed sensor (correct clipping without excessive play).
Check the sensor/ target air gap over one revolution: 0.1 mm < Front wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
Replace the instrumented bearing if the fault recurs.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 16V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0E, 0F
DF006
CONTINUED
Vdiag No.: 0E, 0F
1.DEF
NOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check the quality of the mounting of the wheel speed sensor (correct clipping without excessive play).
Check the sensor/ target air gap over one revolution: 0.1 mm < Front wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
Replace the instrumented bearing if the fault recurs.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 18V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D
DF007
CONTINUED
Vdiag No.: 0C, 0D
Also check the insulation between the following two connections. Repair or replace the wiring if necessary.
Check the insulation, continuity and absence of interference resistance between:
Sensor connector one of the 2 tracks Track 31 on the intermediate connector
Sensor connector the other track Track 32 on the intermediate connector
Also check the insulation between these two connections. Repair or replace the wiring if necessary.
1.DEF
NOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
–Replace the rear left-hand "disc-hub-bearing" assembly (see MR364 or MR370 Mechanical, 33A, Rear axle
components, Bearing: Removal - Refitting) if the fault reappears.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 20V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0E, 0F
DF007
CONTINUED
Vdiag No.: 0E, 0F
Also check the insulation between these two connections.
If the connections are faulty, carry out the following checks:
Check the insulation, continuity and absence of interference resistance between:
Computer connector track 6 Track 32 on the intermediate
connector
Computer connector track 17 Track 31 on the intermediate
connector
Also check the insulation between these two connections.
Check the insulation, continuity and absence of interference resistance between:
Sensor connector one of the
2 tracksTrack 31 on the intermediate
connector
Sensor connector the other track Track 32 on the intermediate
connector
Also check the insulation between these two connections.
If all the checks are in order, contact Techline.
1.DEFNOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap over one wheel revolution: 0.1 mm < Rear wheel gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
–Replace the rear left-hand "disc-hub-bearing" assembly (see MR364 or MR370 Mechanical, 33A, Rear axle
components, Bearing: Removal - Refitting) if the fault reappears.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 21V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF017
PRESENT
OR
STOREDCOMPUTER
1.DEF : Feed fault or internal electronic fault
2.DEF : Programming / initialisation invalid
NOTESSpecial notes:
The voltage displayed in the parameter (PR005) is the + after ignition feed voltage of
the computer and not the hydraulic unit power feed.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Check the connections and the condition of the battery terminals.
Check the condition and position of the ABS fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check the 25A fuse F13 on the UPC and the correct locking of the grey 4-track PPHI connector (Vdiag 44) or
test the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the 26-track connector of the ABS computer.
Check the ABS earths on tracks 1 and 4 (attached under the ABS unit) and carry out an inspection of the entire
ABS wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ Before ignition present
on the tracks) and between the UCH and track 18 of the computer (+ After ignition present on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out another check using the diagnostic tool.
If the fault is still present, contact the Techline.
2.DEF
NOTESSpecial notes:
No programming for PR020 Vehicle speed at initialisation.
ABS warning light flashing at 8 Hz outside fault finding
conditions.
Run command VP032 and select "Type 1" or "Type 2" according to the information supplied by the diagnostic tool.
Clear the computer fault memory, switch the ignition off and carry out a road test. If the fault is still present, contact
the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF017 /ABS8.0_V0D_DF017/ABS8.0_V0E_DF017/ABS8.0_V0F_DF017 ABS 8.0X84 4.0