roof rack RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ABS Workshop Manual

ANTI-LOCK BRAKING SYSTEM
Fault finding - Configurations and programming38C
38C - 10V2 MR-372-J84-38C000$264_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Configurations and programming
Settings
VP001: Write VIN.
This command allows the vehicle identification number to be entered into the computer. Use this
command each time the computer is replaced. The VIN number (VF...) can be found on the
manufacturer's plate on the front right-hand door pillar and on the body panel under the left-hand side
of the windscreen.
VP004: Vehicle parameters.
This command is used to configure the engine type + braking definition + body type.
Select command VP004 on the diagnostic tool (it is imperative to check that the variants selected
correspond to the vehicle type).
VP006: Write date of the last After-Sales service.
Whenever the ABS system is worked on in the shop, the date must be entered.
Select command VP006 on the diagnostic tool.
Enter the operation date with the tool keyboard.
VP007: Tachometric index.
This command is used to program the computer memory with the index required to calculate vehicle
speed from the speed at which the wheels turn.
The BOSCH ABS 8.0 computer supplies the vehicle speed signal to all vehicle systems that use this
information (instrument panel, engine management, etc.). This vehicle speed signal replaces the one
supplied by the speed sensor located on the gearbox. The ABS computer calculates the vehicle speed
from the speed of the wheels and the circumference of the tyres fitted on the vehicle.
Note:
The vehicle speed is sent by wire (track 23) to the xenon bulb computer, radio and electric sunroof, and
via the multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists
of entering a number X using the VP007 "Tachometric index" command on the diagnostic tool.
Once the number has been entered using the VP007 command, delete the fault in the computer memory
and then switch off the ignition. Use the parameter PR030 to check that the index entered has been
stored correctly.
VP032: Vehicle speed at initialisation.
Vehicle speed transmitted via the multiplex network when the computer is initialised.
Select "Type 1" or "Type 2" according to the information supplied by the tool.
ABS 8.0X84 4.0
MR-372-J84-38C000$264_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 22V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF020
PRESENT
TACHOMETRIC INDEX PROGRAMMING
NOTESSpecial notes:
ABS warning light flashing at 8 Hz outside fault finding conditions.
The BOSCH ABS 8.0 computer supplies the vehicle speed signal to all vehicle systems that use this information
(instrument panel, engine management, etc.).
This vehicle speed signal replaces the one supplied by the speed sensor located on the gearbox. The ABS
computer calculates the vehicle speed from the speed of the wheels and the circumference of the tyres fitted on
the vehicle.
Note:
The vehicle speed is sent by wire (track 23) to the xenon bulb computer, radio and electric sunroof, and via the
multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists of
entering a number X using the VP007 "Tachometric index" command on the diagnostic tool.
Once the index has been entered using the VP007 command, clear the computer fault memory and then switch
off the ignition.
Use the parameter PR030 to check that the index entered has been stored correctly.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF020 /ABS8.0_V0D_DF020/ABS8.0_V0E_DF020/ABS8.0_V0F_DF020 ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with commands
38C
38C - 48V2 MR-372-J84-38C000$792_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with commands
CLEARING
RZ001:Fault memory.
This command is used for clearing the computer's stored faults.
ACTIVATION
AC003:
AC004:
AC005:
AC006:Front left-hand wheel solenoid valves.
Front right-hand wheel solenoid valves.
Rear left-hand wheel solenoid valves.
Rear right-hand wheel solenoid valves.
These commands permit a check on the hydraulics of each wheel.
Position the vehicle on a 2-post lift so that the free rotation of the wheels can be checked.
Keep the brake pedal depressed enough to prevent the wheel being tested from being turned by hand (do not brake
so hard that the anti-lock function operates).
Select and confirm the command for the wheel in question (e.g. Left-hand front wheel solenoid valve, etc.).
Turn the wheel concerned by hand: 5 braking/releasing cycles should be detected.
AC013:Wheel speed sensor supply test.
This command is used to check that voltage pulses of approximately 12 V are detected on the faulty
sensor by a multimeter at the terminals of the sensor connector on the computer side.
You must use command AC013 once only.
AC016:Pump motor test.
This command is used to test the pump motor control circuit.
Select command AC016 Pump Motor Test.
The motor must run for 5 seconds.
AC195:Vehicle speed signal.
This command serves to generate a speed other than 0 mph at the computer's vehicle speed wire output
(Track 23) for users of that signal (xenon bulbs, radio, sunroof).
Note:
This command has no visible effect on the dashboard speedometer needle.
–Xenon headlights: Switch on the dipped headlights and run command AC195. Check for slight
variation in the height of the headlight beam while the command is running (the height of the beam is
adjusted to improve visibility according to vehicle speed).
–Radio: Turn on the radio and make sure that the Adjust volume as a function of speed function is
active. Run command AC195. Check that the volume of the sound increases and then decreases
while the command is running.
–Sunroof: This command has no visible effect on the sunroof. This command changes the activation
threshold of the anti-pinch system (the pressure exerted by the sunroof varies with vehicle speed due
to aerodynamic factors).
AC196:Request to switch on hazard warning lights.
This command sends the UCH a request to switch on the hazard warning lights to test their operation
during emergency braking (depending on UCH configuration).
ABS 8.0X84 4.0
MR-372-J84-38C000$792_eng.mif