check engine RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ESP User Guide

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 57V2 MR-372-J84-38C050$496_eng.mif
NO
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF195
PRESENT
OR
STOREDAUTOMATIC GEARBOX MULTIPLEX SIGNALS INVALID
NOTESSpecial notes:
Although it is stored in the computer, this fault does not cause the warning lights to
come on or generate a fault message, because the ABS/ESP system is not faulty. The
ABS/ESP system is not faulty, but has received unusable signals from the automatic
transmission. Run fault finding on the automatic transmission with the diagnostic tool.
Note:
The automatic transmission does not always store these transient faults as quickly as
the ABS/ESP.
If there is no stored fault in the automatic transmission computer memory, start the
engine, and if no present fault is displayed, contact the Techline. Once the fault in the
automatic transmission has been repaired, clear the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
Using the diagnostic tool, check in the parameter screen that the PR063 Vehicle parameters truly correspond with
the vehicle undergoing fault finding.
Is PR063 Vehicle Parameters correct?
YES
Carry out a multiplex network test and check the automatic transmission system using
the diagnostic tool.
If the fault is still present, contact the Techline.
Use command VP004 Vehicle parameters to define the appropriate parameters for the
vehicle type.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a new test with the diagnostic
tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF195 /ESPBOSCH_V09_DF195/ESPBOSCH_V0A_DF195/
ESPBOSCH_V0B_DF195 /ESPBOSCH_V11_DF195/ESPBOSCH_V12_DF195

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 58V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF196
PRESENT
OR
STOREDNO ELECTRIC POWER ASSISTED STEERING MULTIPLEX
SIGNAL
NOTESSpecial notes:
Although the fault is stored in the computer, it is not caused by ABS/ESP components,
but it indicates that the ESP is deactivated due to an electric power steering frame
transmission fault. Run fault finding on the electric power steering.
Note:
The electric power steering does not always store these transient faults as quickly as
the ABS/ESP system.
If there is no stored fault in the electric power steering computer memory, start the
engine; if no present fault is displayed, contact the Techline. Once the fault in the
electric power steering system has been repaired, clear the ABS/ESP computer fault
memory.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the condition and correct locking of the blue PEH connector on the UPC (Vdiag 44) or the grey CT1
connector on the UPC (Vdiag 48).
Carry out a multiplex network test and check the electric power steering system using the diagnostic tool. If the
fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF196 /ESPBOSCH_V09_DF196/ESPBOSCH_V0A_DF196/
ESPBOSCH_V0B_DF196 /ESPBOSCH_V11_DF196/ESPBOSCH_V12_DF196

38C-69
MR-372-J84-38C050$930_eng.mif
V2
38C
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
ALP 1 No dialogue with the ABS computer
NOTESSpecial note:
To run fault finding on the vehicle's computers, switch on the ignition in fault finding
mode (forced + after ignition feed), i.e. proceed as follows:
–With the vehicle card in the card reader, press the Start button for more than
5 seconds without starting conditions being met.
Check that the CLIP diagnostic tool is equipped with the latest update available.
Try to establish dialogue with a computer on another vehicle to make sure that the diagnostic tool is not faulty.
If the tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle, the
cause could be a faulty computer interfering on the multiplex network. Check the battery voltage and carry out the
operations necessary to obtain the correct voltage (9.5 V < battery voltage < 17.5 V).
Carry out a fault finding procedure on the multiplex network using the diagnostic tool.
Check the presence and the condition of the ABS fuses on the passenger compartment fuse board and in the
engine fuse box.
Check that the computer connector is properly connected and check the condition of its connections.
Check the ABS earths (good condition, not corroded, earth screw on top of the ABS unit tight).
Check that the supply to the computer is correct:
–Earth on tracks 1 and 4 of the 46-track connector.
–+ before ignition feed on tracks 2 and 3 of the 46-track connector.
–+ after ignition feed on track 18 of the 46-track connector.
Check that the power supply to the diagnostic socket is correct:
–+ before ignition feed on track 16.
–+ after ignition feed on track 1.
–Earth on tracks 4 and 5.
If dialogue has still not been established after these checks, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP01 /ESPBOSCH_V09_ALP01/ESPBOSCH_V0A_ALP01/
ESPBOSCH_V0B_ALP01 /ESPBOSCH_V11_ALP01/ESPBOSCH_V12_ALP01BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
MR-372-J84-38C050$930_eng.mif

38C-71
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 3 Pull
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Disconnect one wheel speed sensor. Start the
engine and check that only the ABS fault warning
light comes on. Do not drive the vehicle if the brake
fault warning light is also lit, as the brake limiter
function is no longer guaranteed to operate
correctly. Carry out a road test with the ABS
deactivated.
Is the fault still present under these conditions?
no
Raise the vehicle so that you can rotate the wheels
and check:
–Possible inversion when connecting the speed
sensors.
–Possible inversion of pipes on the hydraulic unit.
To carry out these two tests, refer to and follow the
procedures given in ALP 2.
Check the condition of the ABS targets and that they
conform to specifications.
Also check the sensor/target air gap over one
revolution of each front and rear wheel.
If the fault is still present, contact the Techline.
yesIf the brake pedal travel is relatively long,
bleed the brake circuit.
If the travel is normal, check the tyre
pressures, the front axle, or for any leaks
in the circuit.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP03 /ESPBOSCH_V09_ALP03/ESPBOSCH_V0A_ALP03/
ESPBOSCH_V0B_ALP03 /ESPBOSCH_V11_ALP03/ESPBOSCH_V12_ALP03BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-72
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 4 Drift
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Disconnect one wheel speed sensor. Start the
engine and check that only the ABS fault warning
light comes on. Do not drive the vehicle if the brake
fault warning light is also lit, as the brake limiter
function is no longer guaranteed to operate
correctly. Carry out a road test with the ABS
deactivated.
Is the fault still present under these conditions?
no
Normal behaviour linked to the system operation
during the regulation phase, mainly on surfaces with
uneven grip or which are poorly laid.
yesRoad handling fault not connected with
the ABS.
Check the condition of the brake linings
and that they are to specification and
check the tyre pressures, the front axle,
etc.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP04 /ESPBOSCH_V09_ALP04/ESPBOSCH_V0A_ALP04/
ESPBOSCH_V0B_ALP04 /ESPBOSCH_V11_ALP04/ESPBOSCH_V12_ALP04
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-83
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
*ASR: Traction control
ALP15ESP warning light comes on with the "ASR* disconnected or off"
message when the current is switched on without pressing the
ESP disconnection button
NOTESConsult this customer complaint only if the "Service", "ABS" and "Brake" warning lights
are not lit.
After disconnecting the battery, it is probable that the electric power steering loses the steering wheel angle
sensor indexing (the electric power steering no longer sends the steering wheel angle signal to the ESP, which is
then disabled).
The ESP system is not faulty, no fault is present in the fault memory, the ESP warning light comes on and the
"ASR disconnected or off" message indicate this transient and reversible status.
To restore the electric power steering indexing and enable the ESP again, it is necessary to:
–switch on the ignition or start the engine (to obtain maximum steering assistance),
–turn the steering wheel slowly to full right lock, to full left lock, then return slowly to the centre point after going
slightly past it,
–the ESP warning light should go out and the message "ASR disconnected or off" should disappear,
–stop the engine and switch off the ignition,
–switch on the ignition, start the engine and see that the warning light no longer lights up.
If the warning light and the message reappear, start the procedure described above again.
If the operation fails again or if this customer complaint appears without the battery having been disconnected, run
fault finding on the electric power steering and repair accordingly.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP15 /ESPBOSCH_V09_ALP15/ESPBOSCH_V0A_ALP15/
ESPBOSCH_V0B_ALP15 /ESPBOSCH_V11_ALP15/ESPBOSCH_V12_ALP15BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12