ABS RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ESP Workshop Manual

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 5V2 MR-372-J84-38C050$062_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
4. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 6V2 MR-372-J84-38C050$062_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
5. FAULT FINDING LOG
You will always be asked for this log:
●when requesting technical assistance from Techline,
●for approval requests when replacing parts for which approval is mandatory,
●to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed.
6. SAFETY ADVICE
Safety rules must be observed during any work on a component to prevent any damage or injury:
–Check the battery voltage to avoid incorrect operation of computer functions,
–Use the proper tools.
–It is forbidden to carry out a road test while the diagnostic tool is communicating with the computer,
because the ABS and Electronic Braking Distribution (EBD) functions are deactivated. Braking
pressure is identical on both vehicle axles (risk of a spin under heavy braking). IMPORTANTIMPORTANT
Any fault on a complex system requires thorough fault finding with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the procedure, enables you to keep
track of the procedure which is carried out. It is an essential document when consulting the
manufacturer.
IT IS THEREFORE MANDATORY TO FILL OUT A FAULT FINDING LOG EACH TIME FAULT FINDING IS
CARRIED OUT.

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 7V2 MR-372-J84-38C050$186_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
The ESP system on this vehicle incorporates the following functions:
–The ABS (anti-lock braking system). The main functions of the ABS system are electronic front and rear braking
distribution (EBD) by controlling rear wheel slip, and preventing the wheels from locking by controlling the slipping
of all four wheels.
–MSR (engine torque control). Traction control on the driven wheels under no load by limiting the engine braking.
–ASR (traction control). It limits skidding of the drive wheels during starting or acceleration phases by limiting the
engine torque and braking the wheel(s) which are skidding.
–ESP (electronic stability program). Electronic stability program limiting oversteer or understeer by braking certain
wheels and controlling the engine torque.
–CSV (understeer control). Specific control of situations involving pronounced understeer by significant vehicle
braking in conjunction with a specific dynamic stability program.
–AUTOMATIC LIGHTING OF HAZARD WARNING LIGHTS. Generation on the CAN network, for the UCH, of a
request for switching on the hazard warning lights in case of braking causing a very hard deceleration (according
to the legislation of the country).
–AUTOMATIC BRAKE LIGHTS SWITCH-ON. In the event of understeer control (CSV only), the ESP computer
switches on the brake lights, via a relay, to give warning of severe deceleration generated by the system (according
to national legislation).
The system also supplies the other computers with information on the vehicle speed via a wire connection for the
xenon bulbs, the radio and the electric sunroof, and via the multiplex network for the other computers. The ABS/ESP
computer provides the odometry for the instrument panel and navigation aid over the multiplex network.
IDENTIFICATION
From the outside, two factors distinguish an ABS unit from an ABS/ESP unit:
–The size of the units (the ABS/ESP unit is bigger than the ABS) unit. The ABS unit has 8 solenoid valves
and the ABS/ESP unit has 12.
–The number of computer tracks (the ABS computer has 26 tracks and the ABS/ESP computer has
46 tracks).
MR-372-J84-38C050$186_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 8V2 MR-372-J84-38C050$186_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
FAULT FINDING WARNING LIGHT ILLUMINATION STRATEGY for Mégane II ph1 and Scénic II ph 1.
*ASR: Traction controlInstrument panel warning lightInstrument panel message
Meaning
MEGANE II SCENIC II
Brake faults ABS ESPSERVICE STOPESP/ASR*
not workingESP/ASR*
not working,
faulty brakingElectronic braking
regulation and ABS
and ESP not working.
ABS ESP SERVICEESP/ASR*
not workingESP/ASR*
not working
check ABSESP and ABS function
not working.
ESP SERVICEESP/ASR*
not workingESP/ASR*
not workingESP function not
working, Electronic
Braking Distribution
and anti-lock braking
system working
ESPASR*
disconnectedASR*
disconnected–ESP disconnection
button registered
OR
–ESP temporarily
disconnected after
disconnection of the
battery.
Brake faults
flashing at
2 Hz.ABS
flashing at
2 HzESP
flashing at
2 HzNo message No messageABS computer is in
fault finding mode.
Brake faultsABS faults
flashing at
8 HzESP
flashing at
8 HzSTOP No message No messageVehicle parameters
and tachometric index
not programmed.
Brake faults ABSESP
flashing at
8 HzSERVICE STOP No message No messageVehicle parameters
not programmed.
ABS faults
flashing at
8 HzNo message No messageTachometric index not
programmed.
ESP
flashing at
8 HzNo message No messageESP being regulated.
ASR* being regulated.
MSR being regulated.
Note:
The STOP warning light is always accompanied by a single audible warning (1 beep).

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 9V2 MR-372-J84-38C050$186_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
FAULT FINDING WARNING LIGHT ILLUMINATION STRATEGY for Mégane II ph 2 and Scénic II ph 2.
*ASR: Traction controlInstrument panel warning lightInstrument panel message
Meaning
MEGANE II
PH2SCENIC II
PH2
Brake faults ABS ESP SERVICE STOP Braking faultElectronic braking
regulation and ABS
and ESP not working.
ABS ESP SERVICE Check the ABSESP and ABS function
not working, electronic
braking regulation in
backup.
ESP SERVICE Check the ESPESP function not
working, electronic
braking regulation
operational and ABS
in backup.
ESPTRACTION CONTROL
DEACTIVATED
1
–ESP/ASR*
disconnection
button registered
OR
–ESP/ASR*
temporarily
disconnected after
disconnection of the
battery.
Brake faults
flashing at
2 Hz.ABS
flashing at
2 HzESP
flashing at
2 HzNo messageESP computer in fault
finding mode.
Note:
1: On Mégane Sport, this message is replaced by "ASR/ESP off".
The STOP warning light is always accompanied by a single audible warning (1 beep).

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 10V2 MR-372-J84-38C050$186_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
FAULT FINDING WARNING LIGHT ILLUMINATION STRATEGY for Mégane II ph 2 and Scénic II ph 2.
(continued)
*MSR: Engine torque control
*ASR: Traction controlInstrument panel warning lightInstrument panel message
Meaning
MEGANE II
PH2SCENIC II
PH2
ESP
flashing at
8 HzNo messageESP being regulated.
ASR* being regulated.
MSR* being regulated.
ABS faults
flashing at
8 HzNo messageTachometric index
and/or speed at
initialisation not
programmed.
Brake faults ABS ESP
flashing at
8 HzSERVICE STOP No messageVehicle parameters
not programmed.
Brake faultsABS faults
flashing at
8 HzESP
flashing at
8 HzSTOP No messageVehicle parameters
and tachometric index
not programmed.
Vehicle parameters
and speed at
initialisation not
programmed.
Vehicle parameters
and tachometric index
and speed at
initialisation not
programmed.
Note:
The STOP warning light is always accompanied by a single audible warning (1 beep).

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 15V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
DF001
PRESENT
OR
STOREDCOMPUTER SUPPLY VOLTAGE
1.DEF : below minimum threshold
2.DEF : above maximum threshold
3.DEF : abnormal voltage
NOTESSpecial notes:
The fault appears during a road test at a vehicle speed of > 6 mph (10 km/h). The
computer signals an external supply fault.
Conditions for applying the fault finding procedure to stored faults:
Apply the fault finding procedure whether the fault is present or stored.
Check the condition and connection of the battery terminals.
Check the condition and position of the ABS/ESP fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check fuse F13 (25A) on the UPC and the correct locking of the grey 4-track PPH1 connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the ABS/ESP computer 46-track connector.
Check the ABS earths on tracks 1 and 4 (mounted under the ABS/ESP unit) and visually inspect all the
ABS/ESP wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ before ignition feed on
the tracks) and between the UCH and track 28 of the computer (+ after ignition feed on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF001 /ESPBOSCH_V09_DF001/ESPBOSCH_V0A_DF001/
ESPBOSCH_V0B_DF001 /ESPBOSCH_V11_DF001/ESPBOSCH_V12_DF001
MR-372-J84-38C050$434_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 0938C
38C - 20V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09
DF007
PRESENT
OR
STOREDREAR LEFT-HAND WHEEL SPEED SENSOR CIRCUIT
CO.0 : open circuit or short circuit to earth
1.DEF : internal electronic fault of the sensor
2.DEF : magnetic/mechanical target fault
Vdiag No.: 08 and 09
NOTESSpecial notes:
The wheel speed sensors are supplied with + 12 V after ignition but it is not possible
to measure this supply on Vdiag 08 and 09 (supply cut off when the sensor is faulty).
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
NOTESNone
Check the connection and the condition of the sensor connectors.
Swap the two rear wheel speed sensors over.
Clear the computer's fault memory.
Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially displayed, DF007 Rear left-hand wheel speed sensor circuit, changes to DF027 Rear
right-hand wheel speed sensor circuit, replace the wheel speed sensor.
–If the fault remains on the same side, the wiring between the computer and the sensor is faulty.
Check the connection and the condition of the computer connections. Repair if necessary.
Check the connections (Track 31 and 32) at the R2 black 52-track intermediate connection beneath the front
left-hand seat. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the two tracks Track 6 computer connector
Sensor connector the other track Track 27 computer connector
Also check the insulation between these two connections. If the connections are faulty, carry out the following
checks:
Check the continuity, insulation and absence of interference resistance between:
Computer connector track 6 Track 32 on the intermediate connector
Computer connector track 27 Track 31 on the intermediate connector
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF007 /ESPBOSCH_V09_DF007

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 0938C
38C - 21V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09
DF007
CONTINUED
Vdiag No.: 08 and 09
Also check the insulation between these two connections. Repair or replace the wiring if necessary.
Check the continuity, insulation and absence of interference resistance between:
Sensor connector one of the 2 tracks Track 31 on the intermediate connector
Sensor connector the other track Track 32 on the intermediate connector
Also check the insulation between these two connections.
Repair or replace the wiring if necessary.
1.DEF
NOTESNone
Replace the rear left-hand wheel speed sensor.
2.DEF
NOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
Replace the rear left-hand "disc-hub-bearing" assembly (see MR 364 or MR 370 Mechanical, 33A, Rear axle
components, Bearing: Removal - Refitting) if the fault reappears.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 23V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF007
CONTINUED 1
Vdiag: 0A, 0B, 11, 12
NO
Check the connection and the condition of the computer connections. Repair if
necessary.
Check the connections (Track 31 and 32) on the 52-track intermediate black
connection R2 under the front left-hand seat. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the
two tracksTrack 6 computer connector
Sensor connector the other track Track 27 computer connector
Also check the insulation between these two connections. If the connections are faulty,
carry out the following checks:
Check the continuity, insulation and absence of interference resistance between:
Computer connector track 6 Track 32 on the intermediate
connector
Computer connector track 27 Track 31 on the intermediate
connector
Also check the insulation between these two connections.
Check the continuity, insulation and absence of interference resistance between:
Sensor connector one of the
2 tracksTrack 31 on the intermediate
connector
Sensor connector the other track Track 32 on the intermediate
connector
Also check the insulation between these two connections. If all the checks are in order,
contact Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.