gearbox RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ESP Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 85, PDF Size: 0.29 MB
Page 12 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 12V2 MR-372-J84-38C050$310_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
SETTINGS
VP001: Write VIN.
This command permits manual entry of the vehicle's VIN into the computer. Use this command
each time the computer is replaced. The VIN number (VF...) can be found on the manufacturer's
plate on the front right-hand door pillar and on the body panel under the left-hand side of the
windscreen.
VP004: Vehicle parameters.
This command is used to configure the engine type + braking definition + body type.
Select command VP004 on the diagnostic tool (the parameters selected must correspond with
the vehicle type).
VP006: Write last After-Sales operation date.
The date of the operation must be entered whenever the ESP system is worked on in the
workshop. Select command VP006 on the diagnostic tool.
Enter the operation date with the tool keyboard.
VP007: Tachometric index.
This command is used to program the computer memory with the index required to calculate
vehicle speed from the speed at which the wheels turn.
The Bosch 8.0 ESP computer transmits the vehicle speed signal to all areas where this signal is
needed (instrument panel, engine management, etc.). This vehicle speed signal replaces the one
supplied by the speed sensor located on the gearbox.
The ESP computer calculates the vehicle speed from the wheel speed and the tyre
circumference.
Note:
The vehicle speed is conveyed by wire (track 33) to the xenon bulbs, radio and electric sunroof,
and by the multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists
of entering an index X using the diagnostic tool and command VP007 Tachometric index.
Once the index has been entered using the VP007 command, clear the computer fault memory
and then switch off the ignition. Use the PR030 parameter to check that the index has been stored
correctly.
MR-372-J84-38C050$310_eng.mif
Page 14 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 14V2 MR-372-J84-38C050$372_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
Tool faultAssociated
DTCDiagnostic tool title
DF001 50CCComputer supply
DF006 501FFront left-hand wheel speed sensor circuit
DF007 503FRear left-hand wheel speed sensor circuit
DF017 50C3Computer
DF020 50C3Tachometric index programming
DF026 500FFront right-hand wheel speed sensor circuit
DF027 502FRear right-hand wheel speed sensor circuit
DF055 50C3Vehicle parameter programming
DF063 5046Wheel speed inconsistency
DF066 5180No injection multiplex signal
DF090 5041Front right-hand wheel target
DF091 5042Front left-hand wheel target
DF092 5043Rear right-hand wheel target
DF093 5044Rear left-hand wheel target
DF097 5188No automatic transmission multiplex signal
DF126 50F4Combined sensor signal plausibility
DF152 50E6Multiplex network
DF153 50C3Multiplex network
DF186 5182No instrument panel multiplex signal
DF187 50CEBrake light activation relay circuit
DF188 50C6Brake light switch circuit
DF189 50F4Combined sensor circuit
DF190 50F4Combined sensor
DF191 50C9ESP on/off button circuit
DF193 5180Invalid injection multiplex signals
DF194 5158Invalid electric power steering signals
DF195 5188Invalid automatic gearbox multiplex signals
DF196 5158No power-assisted steering multiplex signal
MR-372-J84-38C050$372_eng.mif
Page 27 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 27V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF020
PRESENT
TACHOMETRIC INDEX PROGRAMMING
NOTESSpecial notes: ABS warning light flashing at 8 Hz out of fault finding mode.
The Bosch 8.0 ESP computer transmits the vehicle speed signal to all areas where this signal is needed
(instrument panel, engine management, etc.).
This vehicle speed signal replaces the one supplied by the speed sensor located on the gearbox. The ESP
computer calculates the vehicle speed from the wheel speed and the tyre circumference.
Note:
The vehicle speed is conveyed by wire (track 33) to the xenon bulbs, radio and electric sunroof, and by the
multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists of
entering an X index using the diagnostic tool and the command VP007 Tachometric index.
Once the index has been entered using command VP007 Tachometric index, clear the computer fault memory
and then switch off the ignition. Use parameter PR030 Tachometric index to check that the index entered is being
used correctly by the system.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF020P/ESPBOSCH_V09_DF020P/ESPBOSCH_V0A_DF020P/
ESPBOSCH_V0B_DF020P/ESPBOSCH_V11_DF020P/ESPBOSCH_V12_DF020P
Page 44 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 44V2 MR-372-J84-38C050$434_eng.mif
*USM: NO
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF097
PRESENT
OR
STOREDNO AUTOMATIC TRANSMISSION MULTIPLEX SIGNAL
Vdiag: 0A, 0B, 11, 12
NOTESSpecial notes:
Although it is stored in the computer, this fault does not cause the warning lights to
come on or generate a fault message, because the ABS/ESP system is not faulty. Run
fault finding on the automatic transmission with the diagnostic tool.
Note:
When the fault in the automatic transmission system is repaired, clear the ABS/ESP
fault memory.
The multiplex signal from the automatic transmission is sent to the ABS/ESP via the
Protection and Switching Unit.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Using the diagnostic tool, check in the parameter screen that the PR063 "Vehicle parameters" truly correspond
with the vehicle undergoing fault finding.
Is PR063 Vehicle Parameters correct?
YES
Check the condition and correct locking of the blue PEH connector on the UPC
(Vdiag 44) or the grey CT1 connector on the USM* (Vdiag 48).
Carry out a multiplex network test.
If the fault is still present, run fault finding on the automatic transmission gearbox and
repair as necessary.
If the fault is still present, contact the Techline.
Use command VP004 Vehicle parameters to define the appropriate parameters for the
vehicle type.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a new test with the diagnostic
tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V0A_DF097 / ESPBOSCH_V0B_DF097/
ESPBOSCH_V11_DF097/ESPBOSCH_V12_DF097
Page 57 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 57V2 MR-372-J84-38C050$496_eng.mif
NO
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF195
PRESENT
OR
STOREDAUTOMATIC GEARBOX MULTIPLEX SIGNALS INVALID
NOTESSpecial notes:
Although it is stored in the computer, this fault does not cause the warning lights to
come on or generate a fault message, because the ABS/ESP system is not faulty. The
ABS/ESP system is not faulty, but has received unusable signals from the automatic
transmission. Run fault finding on the automatic transmission with the diagnostic tool.
Note:
The automatic transmission does not always store these transient faults as quickly as
the ABS/ESP.
If there is no stored fault in the automatic transmission computer memory, start the
engine, and if no present fault is displayed, contact the Techline. Once the fault in the
automatic transmission has been repaired, clear the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
Using the diagnostic tool, check in the parameter screen that the PR063 Vehicle parameters truly correspond with
the vehicle undergoing fault finding.
Is PR063 Vehicle Parameters correct?
YES
Carry out a multiplex network test and check the automatic transmission system using
the diagnostic tool.
If the fault is still present, contact the Techline.
Use command VP004 Vehicle parameters to define the appropriate parameters for the
vehicle type.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a new test with the diagnostic
tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF195 /ESPBOSCH_V09_DF195/ESPBOSCH_V0A_DF195/
ESPBOSCH_V0B_DF195 /ESPBOSCH_V11_DF195/ESPBOSCH_V12_DF195