engine oil RENAULT SCENIC 2007 J84 / 2.G Automatic Transmission Siemens TA2005 User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 139, PDF Size: 0.43 MB
Page 82 of 139
AUTOMATIC TRANSMISSION
Fault finding - Conformity check
23A
23A - 82V5 MR-372-J84-23A100$464.mif
SIEMENS TA2005
Vdiag No.: 14-18
SUB-FUNCTION: LOCKUP/UNLOCKING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Engine speedPR006:Engine speed0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
2Calculated
engine torquePR123:Calculated
engine torque0 NmIn the event of a
fault, consult the
interpretation of this
parameter.
3Engine speedPR007:Turbine speed0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
4Engine/turbine
speed
differencePR128:Engine/turbine
speed
difference0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
5Current turbine
speedPR126:Current turbine
speed0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
6Reference
pressurePR138:Reference
pressure21 barIn the event of a
fault, consult the
interpretation of this
parameter.
7Oil pressurePR003:Oil pressureX < 0.2 barIn the event of a
fault, consult the
interpretation of this
parameter.
Page 83 of 139
AUTOMATIC TRANSMISSION
Fault finding - Conformity check
23A
23A - 83V5 MR-372-J84-23A100$464.mif
SIEMENS TA2005
Vdiag No.: 14-18
SUB-FUNCTION: LOCKUP/UNLOCKING (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
8Gearbox oil
pressure sensor
voltagePR118:Gearbox oil
pressure sensor
voltageX = 5 VIn the event of a
fault, consult the
interpretation of this
parameter.
9Exchanger
actuator
solenoid valve
control ET020:Exchanger
actuator
solenoid valve
controlACTIVE
INACTIVEIn the event of a
fault, refer to the
interpretation of this
status.
10Oil temperaturePR004:Gearbox oil
temperature- 40 ˚C < X < 140 ˚CIn the event of a
fault, consult the
interpretation of this
parameter.
11Difference
between
reference
pressure and oil
pressurePR146:Difference
between
reference and oil
pressureX = PR138 - PR003 None.
12Oil too hot signalET010:Oil too hot signalYES, if oil temperature:
X > 140 ˚CIn the event of a
fault, refer to the
interpretation of this
status.
13Sequential
actuator controlAC024:Sequential
actuator controlCommand used to actuate
all the solenoid valves.In the event of a
fault, refer to the
interpretation of this
command.
Page 86 of 139
AUTOMATIC TRANSMISSION
Fault finding - Conformity check
23A
23A - 86V5 MR-372-J84-23A100$464.mif
SIEMENS TA2005
Vdiag No.: 14-18
SUB-FUNCTION: CREEPING AT IDLE SPEED
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Oil pressurePR003:Oil pressureX < 0.2 barIn the event of a
fault, consult the
interpretation of this
parameter.
2Oil temperature PR004:Gearbox oil
temperature- 40 ˚C < X < 140 ˚CIn the event of a
fault, consult the
interpretation of this
parameter.
3Vehicle speedPR105:Vehicle speed0 mphIn the event of a
fault, consult the
interpretation of this
parameter.
4Engine speedPR006:Engine speed0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
5Engine speedPR007:Turbine speed0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
6Engine/turbine
speed
differencePR128:Engine/turbine
speed
difference0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
Page 88 of 139
Fault finding - Status summary table23A
23A - 88V5 MR-372-J84-23A100$522.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Status summary table
Tool status Diagnostic tool title
ET001Solenoid valve supply
ET003Brake light switch (opening)
ET004Brake light switch (closure)
ET010Oil too hot signal
ET011Engine speed signal
ET012Gear lever position
ET013Gear engaged
ET020Exchanger flow control solenoid valve control
ET021Sequence solenoid valve 1 control
ET022Sequence solenoid valve 2 control
ET023Sequence solenoid valve 3 control
ET024Sequence solenoid valve 4 control
ET025Sequence solenoid valve 5 control
ET026Sequence solenoid valve 6 control
ET081Snow mode
ET083Old oil
ET097Manual mode
ET108Torque reduction
ET123Multifunction switch S2
ET124Multifunction switch S3
ET125Multifunction switch S4
ET126Multifunction switch P/N
ET127Lower sequential lever switch
ET128Upper sequential lever switch
ET157Gear lever unlocking
AFTER REPAIRRepeat the conformity check from the start.
MR-372-J84-23A100$522.mif
Page 96 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A-96V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
* EV: Solenoid valve.ET020
EXCHANGER FLOW CONTROL SOLENOID VALVE*
NOTESThere must be no present or stored faults.
The exchanger flow control solenoid valve command status displays "ACTIVE" in the following conditions:
–gearbox oil temperature is above 100˚C,
–engine speed is greater than 2000 rpm.
With other conditions, the solenoid valve status displays "INACTIVE".
Disconnect the computer. Check the cleanliness and condition of the connectors.
Check the continuity of the following connections:
●connection code 5DD, between components 119 and 1019,
●connection code 5DN, between components 119 and 1019.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of component 1019 between the following connections:
●connection code 5DD,
●connection code 5DN.
The value should be 40 Ω ± 2 at approximately 23 ˚C.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the resistance is greater than 50 Ω, check the wiring harness, computer connector and modular connector.
If the status of the command fails to change, use the interpretation of fault DF017 "Exchanger flow solenoid valve
circuit".
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_ET020/DP0TA2005_V18_ET020
Page 108 of 139
Fault finding - Parameter summary table23A
23A - 108V5 MR-372-J84-23A100$638.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR001Coolant temperature
PR003Oil pressure
PR004Gearbox oil temperature
PR006Engine speed
PR007Turbine speed
PR008Computer feed voltage
PR105Vehicle speed
PR118Gearbox oil pressure sensor voltage
PR123Calculated engine torque
PR124Accel. pedal position for downshifting
PR126Current turbine speed
PR128Engine/turbine speed difference
PR135Standard pedal position
PR136Raw pedal position
PR138Reference pressure
PR146Difference between reference and oil pressure
MR-372-J84-23A100$638.mif
Page 110 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters23A
23A - 110V5 MR-372-J84-23A100$696.mif
SIEMENS TA2005
Vdiag No.: 14-18
PR003
OIL PRESSURE
NOTESThere must be no present or stored faults.
Immobilise the vehicle: handbrake on and brake pedal depressed.
Check the oil pressure values on the diagnostic tool:
–engine not running: pressure reading less than 0.2 bar.
–engine at idle speed (~ 820 rpm) and gear lever at D or R: pressure reading ~ 2.6 bar.
–engine speed ~ 1400 rpm and gear lever at D or R: pressure reading ~ 8.7 bar.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_PR003/DP0TA2005_V18_PR003
Page 113 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters23A
23A - 113V5 MR-372-J84-23A100$696.mif
SIEMENS TA2005
Vdiag No.: 14-18
PR007
TURBINE SPEED
NOTESThere must be no present or stored faults.
Turbine speed varies according to oil temperature and pressure.
Turbine speed depends on engine speed.
Check the turbine speed on the diagnostic tool:
Gear lever in position N.
Oil temperature 43 ˚C: engine speed ~ 762 rpmturbine speed ~ 681 rpm.
Oil temperature 45 ˚C: engine speed ~ 743 rpmturbine speed ~ 654 rpm.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_PR007/DP0TA2005_V18_PR007
Page 119 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters23A
23A - 119V5 MR-372-J84-23A100$696.mif
SIEMENS TA2005
Vdiag No.: 14-18
PR126
CURRENT TURBINE SPEED
NOTESThere must be no present or stored faults.
Check the cleanliness and condition of the turbine speed sensor and its connections.
Check the insulation, continuity and the absence of interference resistance to earth, to + 12 V and the
following connections:
●connection code 5DA, between components 119 and 1017,
●connection code 5DB, between components 119 and 1017.
If any of the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the turbine speed on the diagnostic tool:
Gear lever position at N or P.
Oil temperature 43 ˚C: turbine speed ~ 681 rpm and engine speed: ~ 743 rpm.
Oil temperature 45 ˚C: turbine speed ~ 654 rpm and engine speed: ~ 743 rpm.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_PR126/DP0TA2005_V18_PR126
Page 124 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters23A
23A - 124V5 MR-372-J84-23A100$696.mif
SIEMENS TA2005
Vdiag No.: 14-18
PR146
DIFFERENCE BETWEEN REFERENCE PRESSURE AND OIL
PRESSURE
NOTESThere must be no present or stored faults.
The reference pressure values are stored in the transmission computer memory and depend on how the vehicle
is used.
The oil pressure is regulated according to the reference pressure. The oil pressure values must always be close
to the reference pressure.
This parameter is the difference between parameter PR138 Reference pressure and parameter PR003 Oil
pressure.
–engine not running: reference pressure reading 21 bar.
oil pressure reading = 0 bar.
–engine at idle speed (~ 700 rpm) and selector lever at D or R: reference pressure reading ~ 2.7 bar.
oil pressure reading = ~ 2.6 bar.
–engine speed ~ 1400 rpm and selector lever at D or R: reference pressure reading ~ 8.9 bar.
oil pressure reading = ~ 8.7 bar.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_PR146/DP0TA2005_V18_PR146