display RENAULT SCENIC 2007 J84 / 2.G Electrical Equipment - Radio Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 34, PDF Size: 0.23 MB
Page 2 of 34
RADIO
General Information
86A
86A - 2V2 MR-372-J84-86A000$099_eng.mif
186ARADIO
General Information
The tuner-amplifier has a test menu (see radio self-test procedure) to carry out repair operations or fault finding.
The radio will operate for approximately 20 minutes without the ignition being switched to the accessories position.
The radio beeps then switches off.
Diagram:
1Radio
2Aerial
3CD changer
4Speakers/tweeter speakers
5Display
6Steering wheel controls
MR-372-J84-86A000$099_eng.mif
Page 3 of 34
RADIO
General Information
86A
86A - 3V2 MR-372-J84-86A000$099_eng.mif
Special features of radios in the PN range:
PN0: radio with built-in display.
PN1: radio with remote display.
PN2: radio and cassette player with built-in display.
PN3: radio and cassette player with remote display.
PN4: radio and CD player with built-in display.
PN5: radio and CD player with remote display.
Notes:
●All radios are designed to control a CD changer.
●There is a special procedure for replacing the CD changer located in the dashboard front panel.
●According to the vehicle version, the remote displays may have a 24 or 30-track connector or two 15-track
connectors. This display may be built into the instrument panel.
Page 4 of 34
RADIO
General Information
86A
86A - 4V2 MR-372-J84-86A000$099_eng.mif
The radio features allow you to:
–listen to the radio (four geographical zones can be
programmed for FM radio)
–display the name of the station using RDS which
automatically switches to the best transmitter (AF
function),
–receive traffic news (I Traffic function),
–receive news flashes and emergency bulletins
(I News function).
–receive public safety emergency bulletins (PTY 31).
RADIO FUNCTION
The tuner has three selection modes displayed on the
screen and accessible from the radio front panel:
–manual mode (MANU),
–preset mode (PRESET),
–alphabetical mode (LIST).CASSETTE FUNCTION
The cassette plays automatically once cassette mode
has been selected using the steering wheel control or
the front panel.
Only the Dolby fast-forward and rewind with search
controls can be selected by specific buttons.
CD FUNCTION
The CD player can play conventional discs and any
audio tracks on a CD-ROM.
CDs can be played in order or tracks can be chosen at
random.
If a CD changer is being used, random play is possible
on only one of the possible 6 compact discs.
THERMAL PROTECTION
If the radio temperature is too high for it to function
properly, the volume is automatically reduced (without
changing the volume shown in the display).
Should one of the speaker tracks short circuit, the
supply to the amplifier will be cut off.Note:
The Mute function, accessed via the voice
synthesiser or the steering wheel control, stops the
cassette playing.
Page 6 of 34
RADIO
Security code recovery procedure
86A
86A - 6V2 MR-372-J84-86A000$198_eng.mif
RADIO
Security code recovery procedure
2 methods for recovering the pre-code (1 letter and 3 digits):
1For PN type radios:
The pre-code is recovered by removing the RECEIVER and noting the four characters on the barcode that
follow the letter T (see photo no. 114936).
On older versions, note the series number at (B) and the pre-code after the letter T at (C).
2For NR type radios
The pre-code is recovered without removal, by applying the following procedure:
●Switch on the radio.
●Press buttons 1 and 6 simultaneously for approximately 2 seconds.
●The pre-code appears on the display.
Note: on NR type radios, the pre-code remains visible at (A) on the radio (see photo no. 114937).
4 methods for recovering the radio code (4 digits):
1Only the VIN is available: connect to code management on Renault.Net and enter the VIN. The code server gives
the original radio code entered in the World Vehicle Database (BVM).
If the code has not been entered in the World Vehicle Database or is incorrect when the code is entered in the radio,
follow the procedure below:
2The pre-code is available: go back to code management on Renault.Net, enter the pre-code and obtain the radio
code.
3For older vehicles which do not have a radio pre-code, enter the series number of the radio again. For example, for
Philips radio, this code starts with RN. In the photo of the radio, this code is RN277F30194601.
If this code is correct, the radio will operate again; if not, follow the procedure below:
4On Renault.Net, write a help message to be sent to the assistance unit.AB
C
THE VIN MUST BE ENTERED IN ALL 4 SOLUTIONS
WHEN REPLACING PARTS, OR FOR AN UNKNOWN VIN, WRITE A HELP MESSAGE IN CODE
MANAGEMENT ON RENAULT.NET TO UPDATE THE DATABASE.
MR-372-J84-86A000$198_eng.mif
Page 8 of 34
RADIO
Anti-theft code
86A
86A - 8V2 MR-372-J84-86A000$297_eng.mif
THE DISPLAY SHOWS 'CODE' OR '0000'
Entering the security code. The radio beeps
every 2 seconds for 2 minutes then displays
CODE.
No
Is the radio code
known?
Yes
Yes
No
Does the radio show
CODE then 0000?
Yes
Enter the first digit using the wheel control on the
steering wheel or the front panel.
Confirm that the digit is correct by briefly
pressing the lower steering wheel button or front
panel button.
Use the same procedure to enter the remaining
three digits.
Confirm the security code by pressing and
holding the same button or button (6) on the front
panel.
No
Does the radio show
ERROR then CODE?
Yes
(See anti-theft code recovery
procedure)
No
Has the 4-digit code
been obtained?
Go back to scrambled mode. With the
radio off, press the 2, 5 and ON buttons.
Wait approximately 2 minutes until CODE
then 0000 appears.
Does the radio show
ERROR CD then CD
CODE?
Yes
See display shows CD CODE.No
The radio enters "CONFIGURATION" mode (if
being used for the first time) and operates
normally.
Page 9 of 34
RADIO
Anti-theft code
86A
86A - 9V2 MR-372-J84-86A000$297_eng.mif
THE DISPLAY SHOWS "CD CODE"
The radio displays ERROR CD,
CD CODE, then CD-0000.
Enter the code of the old radio connected to the
CD changer.
Enter the first digit using the steering wheel
controls.
Confirm the digit by briefly pressing the lower
button of the steering wheel controls.
Enter the three other digits using the same
procedure.
Confirm the security code by pressing and
holding the same button.
Does the CD changer
code match the radio
code?
Yes
No
Enter the CD changer resetting code obtained
from the Techline. After following the
procedure, the display shows CODE or 0000.The CD changer has registered the new radio
code and operates correctly.
Page 11 of 34
RADIO
Connections
86A
86A - 11V2 MR-372-J84-86A000$495_eng.mif
RADIO
Connections
To allocate the tracks for the different functions that are connected to the radio (CD changer, steering wheel control,
display, aerial), refer to the Wiring Diagrams Technical Note corresponding to the vehicle.
Radio: see Wiring diagrams Technical Note, vehicle, code 261
CD changer: see Wiring diagrams Technical Note, vehicle, code 1272
Display: see Wiring diagrams Technical Note, vehicle, code 1127
For displays which are connected to the instrument panel, the code is 247
Steering wheel control: see Wiring diagrams Technical Note, vehicle, code 325
Aerial: see Wiring diagrams Technical Note, vehicle, code 886
MR-372-J84-86A000$495_eng.mif
Page 12 of 34
RADIO
Self-test procedure
86A
86A - 12V2 MR-372-J84-86A000$594_eng.mif
RADIO
Self-test procedure
The self-test procedure mode of the previous generation radios (PN0-6) allows certain main functions to be tested:
●by pressing buttons 2 and 4 at the same time, the speakers can be tested. They are supplied one by one; the
display enables the connections and signals from each speaker to be checked,
●by pressing buttons 1 and 6 at the same time, the reception level can be tested (after frequency is displayed),
–9 or letter: good reception,
–less than 3: poor reception,
–if 2: total loss of stereo.
The self-test procedure mode of the new generation radios (NR4/5) enables certain main functions to be tested
using the combination of buttons 1, 6 and i. The messages will be displayed in the following way:
●Radio pre-code displays one letter and 3 digits to avoid removal of the radio,
●speaker test with two bleeps (bass - treble) from the speakers, with the tested speakers shown on the display
(front left-hand H01, front right-hand H02, rear right-hand H03, rear left-hand H04),
●displays the frequencies and levels of the tuner sensors,
●software version displayed, displays fault finding for the connected aerial if the aerial is supplied by a coaxial
cable; in this case, the display shows H15 with X = 0, 1 or 2 depending on the aerial status (0: open circuit, 1:
short circuit to earth, 2: power consumption),
●audio test loudness OFF (H08), cuts any loudness for an audio test.
Note:
Also displays source use time and total time in 10 minute slots (Tuner (H09)/CD (H10)/cassette (H11)/CD changer
(H12)/auxiliary (13)/MP (H14)/Total (H15)).
MR-372-J84-86A000$594_eng.mif
Page 13 of 34
RADIO
Radio fault finding: Customer complaints
86A
86A - 13V2 MR-372-J84-86A000$693_eng.mif
RADIO
Radio fault finding: Customer complaints
THE RADIO BEEPS APPROXIMATELY EVERY 2 SECONDS ALP 1
THE RADIO DOES NOT WORK (NO SOUND) WHEN THE RADIO ON
BUTTON IS PRESSEDALP 2
THE RADIO DOES NOT SWITCH ON AUTOMATICALLY WHEN +
ACCESSORIES FEED IS SWITCHED ON OR SWITCHES OFF AFTER 20
MINUTESALP 3
THE RADIO IS SWITCHED ON, BUT THE DISPLAY AND SATELLITE
CONTROLS DO NOT WORKALP 4
THE PLANET WHEEL CONTROLS DO NOT WORK ALP 5
RADIO RECEPTION FAULTSALP 6
THE VOLUME DOES NOT INCREASE WITH THE VEHICLE SPEED ALP 7
LIGHTING DOES NOT CHANGE WHEN THE VEHICLE LIGHTS ARE
SWITCHED ONALP 8
NO SOUND CUT-OUT DURING CARMINAT OR HANDS-FREE KIT
MESSAGESALP 9
THE INFRARED REMOTE CONTROL DOES NOT WORK ALP 10
MR-372-J84-86A000$693_eng.mif
Page 14 of 34
RADIO
Fault finding chart
86A
86A - 14V2 MR-372-J84-86A000$792_eng.mif
RADIO
Fault finding chart
ALP 1 The radio beeps approximately every 2 seconds
The radio beeps approximately every
2 seconds. Wait 2 minutes.
Enter the radio-specific security code
No
Is the code correct?
Yes
The radio enters
Configuration mode
(if being used for the
first time) and operates normally.
See security code, the radio
displays CODE then 0000.No
Yes
The radio displays CODE then
0000. Check the code and try
again.
Has the code been
entered correctly?
MR-372-J84-86A000$792_eng.mif