lock RENAULT SCENIC 2007 J84 / 2.G Electrical Equipment - Radio Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 34, PDF Size: 0.23 MB
Page 7 of 34
RADIO
Anti-theft code
86A
86A - 7V2 MR-372-J84-86A000$297_eng.mif
RADIO
Anti-theft code
The radio is protected by a four digit code. This code
must be entered via the control satellite or the radio
keypad each time the battery is disconnected.
Entering the code with the control on the steering
wheel:
Press the lower button on the control to confirm an
entry.
Entry via the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then
confirm with button 6.
If the code is entered incorrectly, the radio will be
locked (1 minute for the first error, 2 minutes for the
second error, 4 minutes for the third error, etc.
32 minutes maximum).
Some configurations must be set after the code has
been entered for the first time (see the Configuration
Section). These settings are stored when the battery is
disconnected.Reminder:
The radio will operate for approximately 2 minutes in
scrambled mode without the code having been entered
(with regular warning beeps).
If the vehicle is equipped with a CD changer in the
front panel, a code is exchanged between the CD
changer and the radio.
–If a new CD changer is fitted, the radio code is
programmed when the battery or CD changer is
connected.
–If the radio is replaced, enter the security code of the
old radio connected to the CD changer. The CD
changer is programmed with the code for the new
radio.
–If the old radio code is lost, the changer code can be
cleared using the clearing code. The clearing code is
issued by the Techline, server, etc.
Note:
If there is a configuration error, you can return to scrambled mode by pressing the 2 and 5 buttons at the same
time as switching the power on. Then wait 2 minutes.
Note:
The CD changer is supplied uncoded. When it is installed in the vehicle, the CD changer is programmed with the
radio supply code.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered (with
regular warning beeps).
IMPORTANT
If the vehicle is fitted with a top of the range navigation system (ITS), enter the radio code in the following
way:
1. switch on the system by activating the vehicle's + after ignition feed,
2. wait 2 minutes: scrambled mode with beeps from the speakers, then code request screen appears,
3. enter the radio code using the ITS keypad: move the cursor with the central control and press to confirm.
4. switch off the ignition.
MR-372-J84-86A000$297_eng.mif
Page 29 of 34
RADIO
Recovering a jammed CD
86A
86A - 29V2 MR-372-J84-86A000$891_eng.mif
Second solution
If the electric ejector motor is not operational, remove
the bolt (C) and release the electric motor (B).
Turn toothed wheel (D) by hand in a clockwise
direction until the CD is ejected.Before replacing the radio:
●refit the electric motor and attach it using the bolt
(second solution only),
●refit the casing.
RADIO
Page 34 of 34
RADIO
Recovering a jammed CD
86A
86A - 34V2 MR-372-J84-86A000$891_eng.mif
Second solution
If the electric motors are not operational:
1To reinsert the CD and its drawer into changer (5),
remove the pinion mounting (6) by its bolt,
turn the toothed wheel (7) by hand in an
anticlockwise direction until the drawer is turned
completely upside down in the changer (5).2Eject the CD changer by moving the lever (8).
Before replacing the radio:
●refit the module in its unit, replace the four dampers
and the two springs,
●attach the module to the unit using the three bolts,
●re-close the changer, attach its cover and refit the
rear section.
CHANGER IN THE BOOT