navigation system RENAULT SCENIC 2007 J84 / 2.G Electrical Equipment - Radio Workshop Manual

RADIO
Anti-theft code
86A
86A - 7V2 MR-372-J84-86A000$297_eng.mif
RADIO
Anti-theft code
The radio is protected by a four digit code. This code
must be entered via the control satellite or the radio
keypad each time the battery is disconnected.
Entering the code with the control on the steering
wheel:
Press the lower button on the control to confirm an
entry.
Entry via the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then
confirm with button 6.
If the code is entered incorrectly, the radio will be
locked (1 minute for the first error, 2 minutes for the
second error, 4 minutes for the third error, etc.
32 minutes maximum).
Some configurations must be set after the code has
been entered for the first time (see the Configuration
Section). These settings are stored when the battery is
disconnected.Reminder:
The radio will operate for approximately 2 minutes in
scrambled mode without the code having been entered
(with regular warning beeps).
If the vehicle is equipped with a CD changer in the
front panel, a code is exchanged between the CD
changer and the radio.
–If a new CD changer is fitted, the radio code is
programmed when the battery or CD changer is
connected.
–If the radio is replaced, enter the security code of the
old radio connected to the CD changer. The CD
changer is programmed with the code for the new
radio.
–If the old radio code is lost, the changer code can be
cleared using the clearing code. The clearing code is
issued by the Techline, server, etc.
Note:
If there is a configuration error, you can return to scrambled mode by pressing the 2 and 5 buttons at the same
time as switching the power on. Then wait 2 minutes.
Note:
The CD changer is supplied uncoded. When it is installed in the vehicle, the CD changer is programmed with the
radio supply code.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered (with
regular warning beeps).
IMPORTANT
If the vehicle is fitted with a top of the range navigation system (ITS), enter the radio code in the following
way:
1. switch on the system by activating the vehicle's + after ignition feed,
2. wait 2 minutes: scrambled mode with beeps from the speakers, then code request screen appears,
3. enter the radio code using the ITS keypad: move the cursor with the central control and press to confirm.
4. switch off the ignition.
MR-372-J84-86A000$297_eng.mif

RADIO
Configuration - Settings
86A
86A - 10V2 MR-372-J84-86A000$396_eng.mif
CONFIGURATIONS
NOTE:
To select the zone in which the radio is to be used,
press the buttons 2 and 5 while switching the power
on. Then wait approximately 2 min. Enter the four digit
code and then:
●select the tone curve appropriate for the vehicle
–0: no regulation
–1: Twingo
–2: Clio
–3: Mégane / Scénic
–4: Laguna
–5: Vel Satis - Espace
●select the relevant zone:
–America
–Japan
–Asia
–Arabia
–Others (Europe, Africa, other)SETTINGS
To enter configuration mode (Expert mode), press and
hold the Source button (4 seconds) until you hear a
bleep. This allows you to adjust the following functions:
NR range:
●AF mode activation (automatic retuning),
●vehicle speed-dependent volume control (5 for
maximum regulation, 0 to cancel regulation),
●Loudness mode activation.
PN range:
●AF mode activation (automatic retuning),
●vehicle speed-dependent volume control (5 for
maximum regulation, 0 to cancel regulation),
●Loudness mode activation,
●Assisted tuner mode activation,
●configuration of the number of speakers (2 or 4),
●manual or dynamic list selection.
PN6 radio:
●AF mode activation (automatic retuning),
●vehicle speed-dependent volume control (5 for
maximum regulation, 0 to cancel regulation),
●Loudness mode activation,
●Assisted tuner mode activation,
●configuration of the number of speakers (2 or 4),
●manual or dynamic list selection.
●activation of data storage in accordance with the
RENAULT Card: CARD ON/OFF. To operate, the
radio must be accompanied by the navigation
system. Note:
These configurations are not required when the
secret code is entered after the power supply has
been cut.
RADIO
Configuration - Settings
MR-372-J84-86A000$396_eng.mif