instrument panel RENAULT SCENIC 2007 J84 / 2.G Power Assisted Steering Workshop Manual

POWER-ASSISTED STEERING
Fault finding – Introduction
36B
36B-2V5 MR-372-J84-36B000$066_fra.mif
136B
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDER
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–vehicle card in reader,
–press and hold start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the required operations.
To cut off + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the instrument
panel have gone out. Vehicle(s): Scenic II
Function concerned: EPASComputer name: Electric power assisted steering
Vdiag no.: 05, 09, 0D
Special tooling required
Multimeter
Elé. 1681Universal bornier
DAE_V05_ PRELI/DAE_V09_ PRELI/DAE_V0D_ PRELI
MR-372-J84-36B000$066_fra.mif

POWER-ASSISTED STEERING
Fault finding – System operation
36B
36B-8V5 MR-372-J84-36B000$132_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
SIGNALS RECEIVED AND SENT
Vehicle speed
Power-assisted
steering computerSteering wheel angle (Vdiag
05 and 09)
Engine status Column rotation speed
Power supply (permanent +)Instrument panel indicator
light on
Supply (+ after ignition feed) Diagnostic socket
Earth

POWER-ASSISTED STEERING
36B
36B-9V5 MR-372-J84-36B000$198_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Allocation of computer tracks
Electric Power Assisted Steering computer
8-TRACK CONNECTOR
2-TRACK BLACK CONNECTORTrack Description
1Not used
2Not used
3Not used
4CAN L signal to Instrument panel
5CAN L to UCH
6CAN H signal to Instrument panel
7 CAN H to UCH
8+ 12 V after ignition feed
Track Description
1+ 12 V before ignition feed
2Earth
IMPORTANT
The three white connectors which connect the EPAS computer to the different EPAS sensors must never be
disconnected.
You must not press the connectors more than once when checking that they have been correctly locked into place.
Equally, the three electric motor feed wires must never be unscrewed.
MR-372-J84-36B000$198_fra.mif

POWER-ASSISTED STEERING
36B
36B-13V5 MR-372-J84-36B000$396_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Fault summary table
Tool
faultDiagnostic tool titleAssociated
DTCCustomer complaints and warning light
coming on
DF001Motor thermal protection5614Steering assistance intermittent reduction.
DF002Computer5608Assistance limited to 30% (with SERVICE
warning light + message) or no assistance
(with STOP warning light + message)
depending on the internal fault code.
DF020Computer supply5601Degraded assistance (no warning light or
message) until a loss of assistance below
9 V or above 17 V with STOP indicator light
+ Message.
DF021Steering wheel angle sensor
programming (only for Vdiag 05 and 09)5612Degraded steering wheel recall (with
SERVICE indicator light + message). ESP
fault, if present.
DF023+ after ignition feed5613Assistance gradually cuts out (within
5 minutes). When the ignition is next
switched on there is no steering
assistance.
DF033Multiplex networkD000Inappropriate level of assistance:
SERVICE indicator light + Message.
DF035Variable power assisted steering motor5606Assistance limited to 30% (with SERVICE
warning light + message) or no steering
assistance (with STOP warning light
+ Message).
DF038Angle sensor (only Vdiag 05 and 09) 5605Steering wheel recall degraded
(no warning light or message). ESP fault,
if present.
DF053Computer configuration5602Defect mode assistance (no message
or warning light).
DF054Torque sensor5604Steering assistance loss or absence with
STOP indicator light + Message.
DF055Computer memory5607Degraded assistance (without warning
light or message) or assistance limited to
10% with SERVICE warning light
+ Message.
Risk of ESP fault.
DF057Vehicle speed multiplex signalD200Inappropriate level of assistance:
SERVICE indicator light + Message.
Note:
Warning light/message
SERVICE + "Check steering" or,
STOP + audible warning + "Faulty steering" or "EPAS fault", depending on the type of instrument panel.
MR-372-J84-36B000$396_fra.mif

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-20V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF033
PRESENT
OR
STOREDMULTIPLEX NETWORK
DEF: CAN connection fault
NOTESConditions for applying the fault finding procedure to stored faults:
Apply this fault finding procedure.
Priority in the event of a number of faults:
Apply the interpretation of faults DF020 Computer supply and DF023 + after ignition
supply first, if they are present or stored.
Notes:
This fault may cause a reduction in steering assistance with the SERVICE indicator
light + Message.
Run fault finding on the multiplex network.
Carry out the necessary repairs.
Disconnect the 8-track connector from the EPAS computer.
Check the condition and conformity of the connector and its clips (terminals).
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
8-track connector of the EPAS computer
track 5 UCH
track 7 UCH
track 4 Instrument panel
track 6 Instrument panel
(see wiring diagram)
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF033/DAE_V09_DF033/DAE_V0D_DF033

POWER-ASSISTED STEERING
Fault finding – Fault Finding Chart
36B
36B-49V5 MR-372-J84-36B000$924_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
ALP2 Loss of vehicle assistance without warning
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
The vehicle is no longer assisted if the Electric Power Steering fuse is damaged or supply is lost. The steering is
equivalent to manual steering, manoeuvrable when driving even at low speeds, but very difficult to manoeuvre
when stopped.
Since it is no longer being supplied, the EPAS computer is not capable of lighting the warning light, but the
instrument panel lights the STOP warning light + Message 4 seconds after the loss of the feed causing the loss
of assistance.
The driver will only become aware of the fault through noticing the loss of assistance at the steering wheel.
Check the fuses for the electric power-assisted steering:
Power fuse 80A BP81 in the engine fuse box.
5A AP44 + after ignition fuse on the UPC.
Check the condition of the electric power-assisted steering connectors and repair if necessary.
Check that the electrical feeds to the computer are correct:
2-track connector track 2vehicle earth
2-track connector track 1+ battery feed
8-track connector track 8+ after ignition feed
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the connections between the electric
power-assisted steering computer and the instrument panel.
8-track connector track 6 track 30 of the instrument panel
8-track connector track 4 track 29 of the instrument panel
Check that the steering column and steering rack are in sound mechanical condition.
Repair if necessary.
Make sure that the front axle components, such as the track rod ends and shock absorber base plates, are in sound
mechanical condition.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ALP2/DAE_V09_ALP2/DAE_V0D_ALP2