engine RENAULT SCENIC 2008 J84 / 2.G Automatic Transmission Siemens TA2000 User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 128, PDF Size: 0.43 MB
Page 46 of 128
AUTOMATIC TRANSMISSION
Fault finding – Interpretation of faults23A
23A-46V4 MR-372-J84-23A050$330.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
DF109
PRESENT
OR
STORED
ENGINE TORQUE MULTIPLEX SIGNAL
1.DEF: Consistency
2.DEF: Real torque
3.DEF: Anticipated torque
4.DEF: Torque excluding reduction
5.DEF: Requested torque cannot be attained
NOTESNone.
Run a multiplex network test (see 88B, Multiplex).
If the fault is still present, carry out fault finding on the injection system (see 17B, Petrol injection or 13B, Diesel
injection).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the
diagnostic tool.
DP0TA2000_V10_DF109/DP0TA2000_V11_DF109/DP0TA2000_V15_DF109
Page 49 of 128
AUTOMATIC TRANSMISSION
Fault finding – Interpretation of faults23A
23A-49V4 MR-372-J84-23A050$330.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
DF116
PRESENT
OR
STOREDMULTIPLEX ENGINE SPEED SIGNAL
NOTESNone.
Carry out a test on the multiplex network (see 88B Multiplex).
If the fault is still present, run fault finding on the injection system (see 17B, Petrol injection or 13B, Diesel
injection).
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
DP0TA2000_V10_DF116/DP0TA2000_V11_DF116/DP0TA2000_V15_DF116
Page 55 of 128
AUTOMATIC TRANSMISSION
Fault finding – Interpretation of faults23A
23A-55V4 MR-372-J84-23A050$396.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
DF126
PRESENT
OR
STOREDTURBINE SPEED SIGNAL
NOTESThe fault appears when the engine is running and the gear lever is at P.
Disconnect the battery.
Disconnect the modular connector, and check the cleanness and condition of the connections.
Repair if necessary.
Disconnect the computer. Check the cleanliness and condition of the connections.
Use the Universal bornier Elé. 1681 to check the continuity and insulation of the following connections:
●Connection code 5DA, between components 119 and 1017.
●Connection code 5DB, between components 119 and 1017.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Reconnect the modular connector.
Measure the resistance of component 1017 between the following connections:
●Connection code 5DA.
●Connection code 5DB.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
The turbine speed sensor resistance is 300 ΩΩ Ω Ω
± 40 ΩΩ Ω Ω
.
If the value is not correct, replace the turbine speed sensor.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the
diagnostic tool.
DP0TA2000_V10_DF126/DP0TA2000_V11_DF126/DP0TA2000_V15_DF126
Page 62 of 128
AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 62V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Engine
speedPR006:Engine speed0 rpmIn the event of a
fault, consult the
interpretation of
this parameter.
2Gear
selector
positionET012:Gear
selector
position "P" if selector in position "P"
"N" if selector in position "N"
"R" if selector in position "R"
"D" if selector in position "D"
"M" if selector in position "M"
"M+" if selector in position "M+"
"M-" if selector in position "M-"In the event of a
fault, refer to the
interpretation of
this status.
3GearET013:Gear
engagedN for position N
"1" for 1
st unlocked
"2" for 2nd unlocked
"R" for reverse gear positionIn the event of a
fault, refer to the
interpretation of
this status.
4Power
supplyPR008:Computer
feed voltage10.5 < X < 16In the event of a
fault, consult the
interpretation of
this parameter.
Page 63 of 128
AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 63V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
MAIN SCREEN (continued 1)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
5Brake pedalET142:Brake pedal pressedYES, if the brake pedal
is depressed
NO, if the brake pedal
is not depressedIn the event of a
fault, refer to the
interpretation of this
status.
6Brake switchET003:Brake light switch
(opening)ACTIVE, if the brake
pedal is not depressed
INACTIVE, if the brake
pedal is depressedIn the event of a
fault, refer to the
interpretation of this
status.
ET004:STOP light contact
(closure)INACTIVE, if the brake
pedal is not depressed
ACTIVE, if the brake
pedal is depressed
7Selection modeET097: Manual mode INACTIVEACTIVE, if lever is in
position M
8Sequential lever
switchET127:Lower sequential
lever switchOPEN, CLOSED, if
selector lever in
position M-
In the event of a
fault, refer to the
interpretation of this
status. ET128:Upper sequential
lever switchOPEN, CLOSED, if
selector lever in
position M+
ET155:Third gear hold
contactOPEN
9Driving modeET079:Economy modeYES, if driving is
economical
NO, if driving is 'sporty' NONE
10Gearbox oil
temperaturePR004:Gearbox oil
temperature- 40 < X < 140 ˚C In the event of a
fault, consult the
interpretation of this
parameter.
Page 64 of 128
AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 64V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
MAIN SCREEN (continued 2)
*SV: solenoid valve
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
11Heat exchanger
flow control
solenoid valve
controlET020:Exchanger flow
control SV* controlINACTIVEIf ACTIVE, refer to
the interpretation of
this status.
12Old oilET083:Old oilYES
NONo procedure for
running diagnostics
on this status
Page 65 of 128
AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 65V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
SUB-FUNCTION: CHANGING GEAR
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Gear lever
positionET012:Gear lever positionP if selector is in
position P
N if selector is in
position N.
R if selector is in
position R.
D if selector is in
position D.
M if selector is in
position M.
M+ if selector is in
position M+.
M- if selector is in
position M-. In the event of a
fault, refer to the
interpretation of this
status.
2GearET013:Gear engaged"N" for neutral
"1" for 1
st unlocked
"2" for 2
nd unlocked
"R" for reverseIn the event of a
fault, refer to the
interpretation of this
status.
3Engine speedPR006:Engine speed0 rpmIn the event of a
fault, consult the
interpretation of this
parameter.
4Oil pressurePR003:Oil pressureX < 0.2 bar In the event of a
fault, consult the
interpretation of this
parameter.
Page 66 of 128
AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 66V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
SUB-FUNCTION: GEAR CHANGE (CONTINUED 1)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
5Solenoid valve
controlET021:Sequence solenoid 1
controlInactive
In the event of a
fault, refer to the
interpretation of this
status. ET022:Sequence solenoid 2
controlInactive
ET023:Sequence solenoid
valve 3 controlInactive
ET024:Sequence solenoid
valve 4 controlInactive
ET025:Sequence solenoid
valve 5 controlInactive
ET026:Sequence solenoid
valve 6 controlInactive
AC024:Sequential actuator
controlMeans of controlling
all the solenoid
valvesIn the event of a
fault, refer to the
interpretation of this
command.
6Multifunction
switchLever in position P
In the event of a
fault, refer to the
interpretation of this
status. ET123:Multifunction
switch S2CLOSED
ET124:Multifunction
switch S3OPEN
ET125:Multifunction
switch S4OPEN
7FeedsET001: Solenoid valve
supplyPRESENTIn the event of a
fault, refer to the
interpretation of this
status.
Page 67 of 128
AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 67V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
SUB-FUNCTION: GEAR CHANGE (CONTINUED 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
8Selection modeET097:Manual
ModeINACTIVE
ACTIVE, if lever is in
position MIn the event of a
fault, refer to the
interpretation of this
status.
9Sequential lever
switchET127:Lower sequential
lever switchOPEN
CLOSED, if selector
lever in position M-
In the event of a
fault, refer to the
interpretation of this
status. ET128:Upper sequential
lever switchINACTIVE
CLOSED, if selector
lever in position M+
ET155:Third gear hold
contactOPEN
Page 68 of 128
AUTOMATIC TRANSMISSION
Fault finding – Conformity check23A
23A - 68V4 MR-372-J84-23A050$462.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
SUB-FUNCTION: PRESSURE CONTROL
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(no present or stored faults).
Application conditions: engine stopped, ignition on.
The values indicated in this conformity check are given as examples.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Gearbox ratioET013: Gear engagedN for neutral position
1 for 1
st unlocked
2 for 2nd unlocked
R for reverse gear
positionIn the event of a
fault, refer to the
interpretation of this
status.
2Engine speedPR006:Engine speed0 rpmIn the event of a
fault, consult the
interpretation of
fault DF115.
3Oil pressurePR003: Oil pressureX < 0.2 barIn the event of a
fault, consult the
interpretation of this
parameter.
PR138:Reference pressure21 bar None.
PR146:Difference between
reference and oil
pressureX = PR138 - PR003 None.
4Oil temperaturePR004:Gearbox oil
temperature- 40 < X < 140 ˚CIn the event of a
fault, consult the
interpretation of this
parameter.