service RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Instrument Panel Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 63, PDF Size: 0.19 MB
Page 1 of 63
8Electrical equipment
V8 MR-372-J84-83A000$TOC.mif
V8
83A
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V8
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2008
INSTRUMENT PANEL
TDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
Fault finding - Introduction 83A - 2
Fault finding - System operation 83A - 7
Fault finding - Replacement of components 83A - 8
Fault finding - Configurations and programming 83A - 9
Fault finding - Fault summary table 83A - 13
Fault finding - Interpretation of faults 83A - 14
Fault finding - Conformity check 83A - 21
Fault finding - Status summary table 83A - 26
Fault finding - Interpretation of statuses 83A - 27
Fault finding - Parameter summary table 83A - 33
Fault finding - Interpretation of parameters 83A - 34
Fault finding - Command summary table 83A - 40
Fault finding - Interpretation of commands 83A - 41
Fault finding - Customer complaints 83A - 47
Fault finding - Fault finding chart 83A - 48
Page 7 of 63
83A-7
MR-372-J84-83A000$126.mif
V8
83A
INSTRUMENT PANEL
Fault finding - System operation
Instrument panel functions (entry level and mid-range versions):
The instrument panel allows:
–display by needle gauge of the following information:
–Vehicle speed
–Rev counter
–Fuel gauge
–Engine coolant temperature
–Management of 20 warning/indicator lights
–Alphanumeric display of the following information:
–Total and trip mileage
–Oil level
–Messages (68 messages)
–Keyless vehicle messages
–Warning messages
–Management of a multifunction buzzer:
The buzzer is used for the following functions:
–Indicating the operation of the direction indicators.
–Signalling that the lights have been left on.
–Indicating that the driver's or passenger's seat belts are not fastened when driving.
–Indicating that a door or the tailgate is not correctly closed.
–Signalling that the handbrake is on.
–Indicating the low fuel warning.
–Indicating that a speed has been exceeded, for Arabian versions, where an overspeed warning
is legally required.
–Indicating to the driver that the automatic locking when driving has been activated/deactivated.
The following buzzers can sound:
–Side lights on
–Direction indicators
–Management and trip computer display:
–Trip meter
–Fuel consumed
–Average fuel consumption
–Instantaneous fuel consumption
–Fuel range in kilometres and miles
–Distance travelled in kilometres and miles
–Average speed
–Oil service interval in kilometres
–Oil service interval in time
–Programmed speed (if the cruise control and speed limiter feature is present).
–Instrument panel dimmer: when the lights are on, the brightness of the instrument panel can be adjusted
using a button located on the instrument panel.
–In the event that the childproof lock system is not working, the buzzer will sound and a warning message
will appear on the instrument panel.
In vdiag 08 (with program version 040B) and vdiag 0C, the instrument panel can manage a personalised oil service
interval (known as the OCS) by detecting premature oil wear (depending on the engine). If the engine has this oil
wear detection management function, the oil service interval will initially be increased. The oil service interval could
however decrease more quickly if a “severe” type of driving (urban driving, diving in traffic jams, etc.) is detected by
the injection computer. The instrument panel will display a message to request that an oil service be performed
quickly, without necessarily displaying a warning message beforehand.
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$126.mif
Page 8 of 63
83A-8
MR-372-J84-83A000$189.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Replacement of components
1. REPLACING, PROGRAMMING OR REPROGRAMMING THE INSTRUMENT PANEL:
For any operation involving the replacement of the instrument panel, follow the configuration procedure
(see Configuration and programming). IMPORTANT
Before replacing the instrument panel, always note the following parameters:
–PR007 Oil service interval: current value in km
–PR008 Oil service interval: current value in months
–PR009 Mileometer
TDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$189.mif
Page 12 of 63
83A-12
MR-372-J84-83A000$252.mif
V8
INSTRUMENT PANEL
Fault finding - Configurations and programming83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
Special features for English versions
The newly supplied instrument panel is configured, by default, in kilometres.
In addition to the language configuration CF002 Language setting, carry out the calculation below to allow
the instrument panel to display consistent values between the distance before next oil change and the
desired oil change frequency.
To display the oil change frequency in miles, multiply the value in miles indicated in the Maintenance
booklet by 10 then divide by 6, to find the exact figure in kilometres.
After the value has been entered, the computer automatically performs the conversion into miles for the
oil service interval.
It is imperative to use the following procedure for correct functioning of the range and oil change
frequency.
Example: 18,000 miles x 10 = 180 000 miles, then divide by 6 = 30,000 km (Enter 30)
Check by reading parameter PR005 Oil change frequency in km.
A) Program the distance to next oil service in kilometres using command VP008 Distance to next oil
service: current value in KM.
Check by reading parameter PR007 Distance to next oil service: current value in KM.
B) Program the oil change frequency in months using command VP007 Oil change frequency in
months.
Check by reading parameter PR006 Oil change frequency in months.
C)Program the oil service interval in months using command VP009 Oil service interval: actual value in
months.
Check by reading parameter PR008 Oil service interval: actual value in months.
D) Program the fuel sender using command VP011 Fuel sender calibration.
There are 2 pieces of information to provide:
–Type of fuel (check by reading configuration LC049).
–Fuel level indicator:
–analogue (needle display),
–digital (bargraph display).
Page 24 of 63
83A-24
MR-372-J84-83A000$441.mif
V8
INSTRUMENT PANEL
Fault finding - Conformity check83A
TDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
MILEOMETER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Ignition on, engine off.
Order FunctionParameter, Status
Check or ActionDisplay and notes Fault finding
1Odometer PR009:OdometerIndicates the counter
value in km.
If the fault is still present,
contact Techline. 2
Oil change
intervalPR007:Oil service
interval: current
value in kmIndicates the distance
to the next oil service
in km (this value must
be less than or equal
to the oil service
interval).
3PR008:Oil service
interval: actual
value in monthsIndicates the time
remaining to the oil
service in months (this
value must be less
than or equal to the
frequency).
4
Oil change
frequencyPR005:Oil change
frequency in
miles (kms)Indicates the oil
change frequency in
miles (kms)
(e.g.: 18,000 miles
(30,000 km))
5PR006:Oil change
frequency in
months.Indicates the oil
change frequency in
months
(e.g.: 24 months)
Page 33 of 63
83A-33
MR-372-J84-83A000$630.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR002Fuel sender unit resistance
PR005Oil change frequency in km.
PR006Oil change frequency in months.
PR007Distance to next oil service: actual value in km
PR008Oil service interval: actual value in months
PR009Mileometer
PR027Coolant temperature
PR035Fuel level
PR099Vehicle speed
PR110Battery voltage
PR111Lighting dimmer voltage
PR112Fuel flow
PR115LPG fuel level
PR116Engine speed
PR117Fuel consumed since trip computer reset
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$630.mif
Page 40 of 63
83A-40
MR-372-J84-83A000$756.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Command summary table
Tool command Diagnostic tool title
RZ001Fault memory
AC006Buzzer
AC007Display
AC008Instrument panel needle gauges
AC009Instrument panel warning lights
AC010Lighting
AC011Symbol display
VP002Write VIN
VP006Oil change frequency in km.
VP007Oil change frequency in months.
VP008Distance to next oil service: actual value in km
VP009Oil service interval: actual value in months
VP010Mileometer updating
VP011Fuel tank sender unit calibration
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$756.mif