warning RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Multiplexing Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 25, PDF Size: 0.09 MB
Page 11 of 25
88B - 11
MULTIPLEXING
Fault finding - Configuration
88B
V4 MR-372-J84-88B050$600_eng.mif
MULTIPLEXING
Fault finding - Configuration
MULTIPLEX NETWORK CONFIGURATION
The tool displays the UCH and Airbag configurations.
The Configuration screen consists of two tabs for displaying and modifying:
–The first tab: Multiplex network configuration indicates the multiplex network version and the list of computers
defined as present on the multiplex network.
–The second tab Configuration of computers supporting fault finding indicates the relevant diagram number,
and the list of computers defined as able to support fault finding with the CLIP tool.
NOTESThe configuration is entered with the ignition on; apply the forced + after ignition
feed procedure (see Introduction).
It can be run from the multiplex network test results screens.
WARNING
Enter the correct diagram version number,
–Scénic II ph1: version 1.
–Scénic II ph2: version 2 with ITS (Vdiag 04) navigation computer.
–Scénic II ph2: version 3 with 4R or other navigation computer (Vdiag 24) or without navigation computer.
–Scénic II ph2: version 4 with LPN navigation computer.
First repair the computers containing the multiplex network configuration (airbag and UCH) to be able to
display the screen with the multiplex network configuration diagram for the diagnosed vehicle.
IMPORTANT
A computer connected to the multiplex network but not declared as being among the computers containing the
multiplex network configuration will not be checked in the multiplex network test.
Correct the configuration by declaring the computer as present if it is absent in the Airbag and UCH computer.
Carry out the multiplex network test again after modifying the configurations.
MR-372-J84-88B050$600_eng.mif
Page 22 of 25
88B - 22
MULTIPLEXING
Fault finding - Fault Finding Chart
88B
V4 MR-372-J84-88B050$900_eng.mif
ALP 1
CONTINUED 2
NOTESVehicle computer power supply for fault finding:
insert the vehicle card in the card reader.
Press and hold (over 5 seconds) the Start button in the absence of start conditions (for
example: selecting a gear).
Connect the diagnostic tool and perform the required operations.
IMPORTANT
To supply the discharge bulb computers, switch on the dipped headlights.
Use Technical Note Wiring diagram, Scénic II ph2.
2. Alliance fault finding sensor (with the possibility of a wireless connection):
Deal with the fault finding for each warning light in the following order of priority: from warning light 1 to warning light 3.
Description
of warning
lights
displayed on
the sensor
from left to
rightWarning light 1 shows
the supply statusWarning light 2 shows
the type and status of
the connectionWarning light 3 shows
the level of
communication with
the vehicleReserved
for the
Nissan tool
OffSensor not connected to
the vehicle or
connection faultNo connection to clip or
connection faultNo dialogue with the
computers-
GreenSensor supplied Wireless connectionGreen flashing:
communication in progress-
Orange-Connection with USB port - -
RedInitialisation fault - Communication error -
To be
checkedIf red or off:
–Fault with initialisation
or connections;
disconnect and
reconnect several
times and if there is
no conclusive result
try with another
sensor. If the sensor
works then replace
the sensorIf off:
–With a wireless
connection: Try with a
USB cable. If the
warning light is orange,
check the wireless
connection configuration
and if it is not correct,
call the Technical
Assistance (Techline).
–With a wired connection:
Try with another cable,
another clip or another
sensor in order to
determine the defective
component.If warning light 3 is off or
red and warning light 2 is
on:
–in this case, during the
multiplex network test
check that the green
warning light flashes and
that the test conditions
have been met (+ after
ignition feed, vehicle
selection, etc.) otherwise
apply the electrical
checks below.If the
warning
light is on:
Contact
Technical
Assistance
(Techline).