RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Network Interface Unit BIC Owner's Guide

86D-31
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-372-J84-86D050$120.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of statuses86D
BIC
Vdiag No.: 14
ET009
ET011
ET012
ET020
ET023
ET024
ET025
CONTINUED
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on the
following connections:
•34AT between components 1519 (or 325) and 1714,
•34AR between components 1519 (or 325) and 1714,
•34AS between components 1519 (or 325) and 1714,
•34AQ between components 1519 (or 325) and 1714,
•34AU between components 1519 (or 325) and 1714,
•34AP between components 1519 (or 325) and 1714.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the radio control satellite (see MR 405 (Espace IV Phase 2) or MR 370 (Scénic II Phase 2), Mechanical,
86A, Radio, Radio satellite control: Removal - Refitting).
Replace the multimedia network interface unit, component code 1714 (see MR 405 (Espace IV Phase 2) or
MR 370 (Scénic II Phase 2) Mechanical, 83C, On-board telematics system, Multimedia network interface
unit: Removal - Refitting).
If the fault is still present, contact Techline.

86D-32
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-372-J84-86D050$120.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of statuses86D
BIC
Vdiag No.: 14
ET017WHEEL ACTION
STATUS DEFINITIONDownwards: This means that the wheel is turned downwards.
Upwards: This means that the wheel is turned upwards.
Inactive: This means that there is no action on the wheel.
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Check the condition and connection of the radio control satellite connector, component code 1519 (for Scénic II
Phase 2) or component code 325 (for Espace IV Phase 2) and the multimedia network interface unit connector,
component code 1714.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on the
following connections:
•34AT between components 1519 (or 325) and 1714,
•34AR between components 1519 (or 325) and 1714,
•34AS between components 1519 (or 325) and 1714,
•34AQ between components 1519 (or 325) and 1714,
•34AU between components 1519 (or 325) and 1714,
•34AP between components 1519 (or 325) and 1714.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
BIC_V14_ET017

86D-33
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-372-J84-86D050$120.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of statuses86D
BIC
Vdiag No.: 14
ET017
CONTINUED
Replace the radio control satellite (see MR 405 (Espace IV Phase 2) or MR 370 (Scénic II Phase 2), Mechanical,
86A, Radio, Radio satellite control: Removal - Refitting).
Replace the multimedia network interface unit, component code 1714 (see MR 405 (Espace IV Phase 2) or
MR 370 (Scénic II Phase 2) Mechanical, 83C, On-board telematics system, Multimedia network interface
unit: Removal - Refitting).
If the fault is still present, contact Techline.

86D-34V1 MR-372-J84-86D050$130.mif
86D
BIC
Vdiag No.: 14
Tool Parameter Diagnostic tool title
PR002Battery voltage
PR003Vehicle speed
PR004External temperature
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Parameter summary table

86D-35V1 MR-372-J84-86D050$140.mif
86D
BIC
Vdiag No.: 14
*LPN: Low Price NavigationTool command Diagnostic tool title Description
RZ001:Fault memoryThis command is used for clearing the stored
faults from the computer.
AC002:On/Off ButtonUsed to simulate the pressing of the On/Off button
of the LPN* radionavigation.
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Command summary table

86D-36V1 MR-372-J84-86D050$150.mif
86D
BIC
Vdiag No.: 14
NOTESOnly refer to the customer complaints after performing a complete check using
the diagnostic tool.
NO DIALOGUE WITH THE COMPUTER ALP 1
THE MULTIMEDIA SYSTEM DOES NOT SWITCH ON ALP 2
STEERING COLUMN SWITCH FAULT ALP 3
EXTERNAL TEMPERATURE DISPLAY FAULT ALP 4
BACKLIGHTING DOES NOT CHANGE WHEN THE VEHICLE LIGHTS ARE
SWITCHED ONALP 5
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Customer complaints

86D-37
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-372-J84-86D050$160.mif
86D
BIC
Vdiag No.: 14
ALP 1 No dialogue with the computer
NOTESUse the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Important: After switching on the system, there can be a delay of 20 seconds before
dialogue is established.
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty. If the
diagnostic tool is not causing the fault and dialogue cannot be established with any other computer on the same
vehicle, it may be that a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations to obtain the correct
voltage (12 V < X < 15 V).
Check the presence and condition of the computer supply fuses:
–for Espace IV Phase 2: F15 (30 A),
–for Scénic II Phase 2: SHUNT (2AA).
Check the connection of the multimedia network interface unit connector, component code 1714 and the condition
of its connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that the computer is correctly supplied by checking the following connections:
•BP3A between components 260 and 1714 (for Espace IV Phase 2),
•BCP3 between components 260 and 1714 (for Scénic II Phase 2),
•BPT between components 645 and 1714 (for Scénic II Phase 2),
•MAN between component 1714 and earth (for Scénic II Phase 2),
•NC between component 1714 and earth (for Espace IV Phase 2).
If the connection(s) is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
BIC_V14_ALP1
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart

86D-38
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 1
CONTINUED
Check that the diagnostic socket, component code 225, is correctly supplied on the following connections:
–for Espace IV Phase 2:
•BCP4 between components 225 and unitary fuse 710,
•AP10 between components 225 and 260 (+ after ignition feed),
NC and MB of component 225.
–for Scénic II Phase 2:
•BP32 between components 225 and 260,
•AP43 between components 225 and 1337 (+ after ignition feed),
•NAM and MAM of component 225.
Check the continuity, insulation and absence of interference resistance on the following connections:
•107W and 107X between components 1714 and 225,
•133B and 133C between components 1714 and 225 (for Espace IV Phase 2)
•133B and 133C between components 1714 and 645 (for Scénic II Phase 2).
If the connection(s) is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If dialogue is still not established after these various checks, replace the multimedia network interface unit,
component code 1714 (see MR 405 (Espace IV Phase 2) or MR 370 (Scénic II Phase 2) Mechanical, 83C,
On-board telematics system, Multimedia network interface unit: Removal - Refitting).
If the fault is still present, contact Techline.

86D-39
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 2 Multimedia system not switching on
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Is it possible to establish dialogue with the
computer?Refer to ALP 1 No dialogue with the computer.
Check the conformity of status ET002 Radio
on/off button (see Conformity check).
Is the result of the check correct?
Check that the LPN* radionavigation on/off
button is operating correctly (see 86A, Radio).
Is the result of the check correct?Contact the Techline.
NO
YES
YESA
NO
NO
YES
B
BIC_V14_ALP2

86D-40
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
*LPN: Low Price Navigation
ALP 2
CONTINUED 1
Check the insulation, continuity and the
absence of interference resistance on
connection 34HY between components 1714
and 261.
Are the checks correct?
If the connection or connections are faulty and
there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Check the insulation, continuity and the
absence of interference resistance of
connection 34HU between components 1714,
261 and 1127.
Are the checks correct?
Contact the Techline.
B
YES
NO
YES
NO
YES