air condition RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Network Interface Unit BIC Workshop Manual

86D -4V1 MR-372-J84-86D050$010.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Introduction86D
BIC
Vdiag No.: 14
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool when the data
is inconsistent. Therefore, this stage is used to:
–carry out fault finding on faults that do not have a fault display, and which may correspond to a customer complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repair.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the
corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is correct but the customer complaint is still present, the fault should be
processed by customer complaints.
A summary of the overall procedure to follow is provided on the following page in
the form of a flow chart

86D-17
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-372-J84-86D050$090.mif
86D
BIC
Vdiag No.: 14
DF001
PRESENT
OR
STOREDCOMPUTER CONFIGURATION
1.DEF: Blank or incomplete configuration.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
Configure the system using configuration CF007 Vehicle configuration (see Configuration and Programming).
If the fault persists, contact your Techline.
BIC_V14_DF001
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of faults

86D-18
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-372-J84-86D050$090.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF002
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
Replace the multimedia network interface unit, component code 1714 (see MR 405 (Espace IV Phase 2) or
MR 370 (Scénic II Phase 2) Mechanical, 83C, On-board telematics system, Multimedia network interface
unit: Removal - Refitting).
If the fault persists, contact your Techline.
BIC_V14_DF002

86D-19
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-372-J84-86D050$090.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF005
PRESENT
OR
STOREDSUPPLY
1.DEF: Overvoltage.
2.DEF: Undervoltage.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
Special notes:
The undervoltage fault appears if the computer feed voltage is less than or equal to
7.5 V for at least 1 second.
The overvoltage fault appears if the computer feed voltage is greater than or equal to
18.5 V for at least 1 second.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
1.DEF
NOTESNone.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
BIC_V14_DF005

86D-20
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-372-J84-86D050$090.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF005
CONTINUED
2.DEFNOTESNone.
Remove the card from the reader or the key from the ignition, then check the condition of the battery, component
code 107.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the condition of fuse F15 (30 A) for Espace IV Phase 2 or fuse SHUNT (2AA) for Scénic II Phase 2.
Check the connection and condition of the connectors of the multimedia network interface unit computer,
component code 1714, depending on the vehicle equipment.
If any connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connectors, otherwise replace the wiring.
Disconnect the computer connector and check the conformity of the following connections:
•BP3A between components 260 and 1714 (for Espace IV Phase 2),
•BCP3 between components 260 and 1714 (for Scénic II Phase 2),
•BPT between components 645 and 1714 (for Scénic II Phase 2),
•MAN between component 1714 and earth (for Scénic II Phase 2),
•NC between component 1714 and earth (for Espace IV Phase 2).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.

86D-21
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-372-J84-86D050$090.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF006
PRESENT
OR
STOREDACTIVATION SIGNAL
CO: Open circuit.
CC.0: Short circuit to earth.
CC.1: Short circuit to +12 volts.
NOTESFault finding procedure application conditions:
The fault is declared present after:
–The + after ignition feed is activated, then the multimedia system was switched on
using the on/off button.
–The fault is declared stored after the vehicle is completely shut off (1 minute after
locking).
If the fault is present, the multimedia functions do not operate.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Check the connection and condition of the connectors of the radio, component code 261, the display, component
code 1127, and the multimedia network interface unit, component code 1714.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation to earth and to +12 V, the continuity, and the absence of interference resistance of the
following connections:
•34HU between components 261 and 1714,
•34HU between components 1127 and 1714.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
BIC_V14_DF006

86D-24
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-372-J84-86D050$090.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF011
PRESENT
OR
STOREDEXTERNAL TEMPERATURE SENSOR CIRCUIT
CC.0: Short circuit to earth
CC.1: Open circuit or short circuit to +12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the ignition is switched off and back on.
Configure the system using CF007 Vehicle configuration (see Configuration and Programming).
If the fault is still present, contact the Techline.
BIC_V14_DF011

86D-30
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-372-J84-86D050$120.mif
86D
BIC
Vdiag No.: 14
ET009
ET011
ET012
ET020
ET023
ET024
ET025REPEAT BUTTON
+ BUTTON
- BUTTON
MUTE BUTTON
SOURCE BUTTON
MODE BUTTON
TELEPHONE BUTTON
STATUS DEFINITIONPRESSED: This means that the button is pressed.
RELEASED: This means that the button is released.
NOTESThere must be no present or stored faults.
Note: ET009 Repeat button is not present on the Espace IV Phase 2.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Check the condition and connection of the radio control satellite connector, component code 1519 (for Scénic II
Phase 2) or component code 325 (for Espace IV Phase 2) and the multimedia network interface unit connector,
component code 1714.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
BIC_V14_ET009 / BIC_V14_ET011 / BIC_V14_ET012 / BIC_V14_ET020 / BIC_V14_ET023 / BIC_V14_ET024 / BIC_V14_ET025
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of statuses

86D-32
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-372-J84-86D050$120.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of statuses86D
BIC
Vdiag No.: 14
ET017WHEEL ACTION
STATUS DEFINITIONDownwards: This means that the wheel is turned downwards.
Upwards: This means that the wheel is turned upwards.
Inactive: This means that there is no action on the wheel.
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Check the condition and connection of the radio control satellite connector, component code 1519 (for Scénic II
Phase 2) or component code 325 (for Espace IV Phase 2) and the multimedia network interface unit connector,
component code 1714.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on the
following connections:
•34AT between components 1519 (or 325) and 1714,
•34AR between components 1519 (or 325) and 1714,
•34AS between components 1519 (or 325) and 1714,
•34AQ between components 1519 (or 325) and 1714,
•34AU between components 1519 (or 325) and 1714,
•34AP between components 1519 (or 325) and 1714.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
BIC_V14_ET017

86D-37
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-372-J84-86D050$160.mif
86D
BIC
Vdiag No.: 14
ALP 1 No dialogue with the computer
NOTESUse the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Important: After switching on the system, there can be a delay of 20 seconds before
dialogue is established.
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty. If the
diagnostic tool is not causing the fault and dialogue cannot be established with any other computer on the same
vehicle, it may be that a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations to obtain the correct
voltage (12 V < X < 15 V).
Check the presence and condition of the computer supply fuses:
–for Espace IV Phase 2: F15 (30 A),
–for Scénic II Phase 2: SHUNT (2AA).
Check the connection of the multimedia network interface unit connector, component code 1714 and the condition
of its connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that the computer is correctly supplied by checking the following connections:
•BP3A between components 260 and 1714 (for Espace IV Phase 2),
•BCP3 between components 260 and 1714 (for Scénic II Phase 2),
•BPT between components 645 and 1714 (for Scénic II Phase 2),
•MAN between component 1714 and earth (for Scénic II Phase 2),
•NC between component 1714 and earth (for Espace IV Phase 2).
If the connection(s) is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
BIC_V14_ALP1
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart