check engine RENAULT SCENIC 2008 J84 / 2.G Engine Compartment Connection Unit Owner's Manual

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-29V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF015
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F2 (7.5A) for the Protection and Switching Unit, connection code 1337.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–MAS between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-30V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF016
PRESENT
OR
STOREDLEFT-HAND DIPPED HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the left-hand dipped beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the left-hand headlight, component code 227
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth, connection code MAS for the left-hand headlight connector, component code 227 is
perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the left-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF016/USM_V4C_DF016

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-31V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF016
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F4 (10A) for the Protection and Switching Unit.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-32V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF017
PRESENT
OR
STOREDRIGHT-HAND DIPPED HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the right-hand dipped beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the right-hand headlight, component code 226
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the right-hand headlight, component code 226 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the right-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF017/USM_V4C_DF017

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-33V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF017
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F3 (10A) for the Protection and Switching Unit.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–CPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-34V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF018
PRESENT
OR
STOREDLEFT-HAND MAIN BEAM HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the left-hand main beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the left-hand headlight, component code 227
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth, component code MAS for the left-hand headlight connector, component code 227 is
perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–RPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the left-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF018/USM_V4C_DF018

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-35V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF018
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F6 (10A) for the Protection and Switching Unit.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–RPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-36V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF019
PRESENT
OR
STOREDRIGHT-HAND MAIN BEAM HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the right-hand main beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the right-hand headlight, component code 226
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the right-hand headlight, component code 226 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–RPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the right-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF019/USM_V4C_DF019

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-37V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF019
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F7 (10A) for the Protection and Switching Unit.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–RPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-38V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF020
PRESENT
OR
STOREDFRONT FOG LIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the front fog light bulbs are sound.
Repair if necessary.
Check the condition and connection of the 2-track connectors for the front fog lights, component code 176 and
177 (tabs broken, bent or oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the front right-hand fog light, component code 176 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check that the earth on connection code MAS for the front left-hand fog light, component code 177 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–8E between components 1337 and 177,
–8F between components 1337 and 176.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the fitting and switch for the front fog lights.
Repair if necessary or replace the light(s) if faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF020/USM_V4C_DF020