wiring RENAULT SCENIC 2008 J84 / 2.G Parking Distance Control Workshop Manual

PARKING DISTANCE CONTROL
Fault finding - Introduction
87F
87F - 2V4 MR-372-J84-87F000$066_eng.mif
187F
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP + multiplex line sensor
Special tooling required
3. RECAP
To run fault finding on the vehicle computers, switch on the ignition.
Depending on the type of vehicle equipment, proceed as follows:
To cut off the + after ignition feed, proceed as follows:Vehicle(s): CLIO III, Laguna II ph 1 and 2
Vel-Satis ph1 and 2,
Espace IV ph1 and 2,
Mégane II, Scénic II, Modus ph2Computer name: Parking distance control
Vdiag No: 04-08
Special tooling required
Multimeter
Elé. 1681 Universal bornier
For vehicles with radio frequency remote control/key,
switch on the ignition with the key.
For vehicles with a Renault card,
with the vehicle card in the card reader,
press and hold start button (longer than 5 seconds) with start-up conditions not fulfilled,
connect the diagnostic tool and perform the required operations.
For vehicles with key/radiofrequency remote control, use the key to switch off the ignition.
For vehicles with a Renault card,
press the Start button twice briefly (less than 3 seconds),
ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the
instrument panel have gone out.
AAP_V04_PRELI/AAP_V08_PRELI
MR-372-J84-87F000$066_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Introduction
87F
87F - 5V4 MR-372-J84-87F000$066_eng.mif
Vdiag No: 04-08
4. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 13V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF002
PRESENT
OR
STOREDLEFT-HAND OUTER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (READY): the parking distance control warning light is not
lit, see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
If a combination of faults are present on the sensors:
Check the connection and condition of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between Tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Left-hand outer sensor
Track 9 Track 1
Track 15 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF002/AAP_V08_DF002
MR-372-J84-87F000$462_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 14V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF002
(CONTINUED)
2 connectors:
12-track parking distance control computer
connectorLeft-hand outer sensor
Track 11 Track 1
Track 5 Track 2
Track 8 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 15V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
DF003
PRESENT
OR
STOREDLEFT-HAND INNER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (READY): the parking distance control warning light is not
lit, see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
When dealing with a combination of faults on the sensors:
Check the connection and the status of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between Tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between Tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Left-hand inner sensor
Track 9 Track 1
Track 14 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF003/AAP_V08_DF003

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 16V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF003
(CONTINUED)
2 connectors:
12-track parking distance control computer
connectorLeft-hand inner sensor
Track 11 Track 1
Track 3 Track 2
Track 8 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 17V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF004
PRESENT
OR
STOREDRIGHT-HAND OUTER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (ready): the parking distance control warning light is not lit,
see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
When dealing with a combination of faults on the sensors:
Check the connection and the status of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Right-hand outer sensor
Track 9 Track 1
Track 16 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF004/AAP_V08_DF004

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 18V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF004
(CONTINUED)
2 connectors:
12-track parking distance control computer
connectorRight-hand outer sensor
Track 11 Track 1
Track 4 Track 2
Track 8 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.

PARKING DISTANCE CONTROL
87F
87F - 19V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF005
PRESENT
OR
STOREDRIGHT-HAND INNER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (READY): the parking distance control warning light is not
lit, see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
If a combination of faults are present on the sensors:
Check the connection and condition of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Right-hand inner sensor
Track 9 Track 1
Track 13 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF005/AAP_V08_DF005

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 20V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF005
(CONTINUED)
2 connectors:
12-track parking distance control computer
connectorRight-hand inner sensor
Track 11 Track 1
Track 2 Track 2
Track 8 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.