sensor RENAULT SCENIC 2009 J84 / 2.G Engine And Peripherals EDC16 User Guide

DIESEL INJECTION
Fault finding – Fault summary table13B
13B-27V3 MR-372-J84-13B250$270.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
Tool
faultDIAGNOSTIC
TOOL
DESCRIPTIONAssociated
DTCLEVEL 1 FAULT
WARNING
LIGHT (Orange
heater plugs On
indicator light)LEVEL 2 FAULT
WARNING
LIGHT (Red
overheating
warning light)NO
FAULT
WARNING
LIGHT ONOBD
WARNING
LIGHT ON
DF038Computer 6066.DEF/8.DEF/
12.DEF1.DEF/2.DEF/
3.DEF/4.DEF/
5.DEF/7.DEF/
10.DEF/11.DEF/
13.DEF/14.DEF... 6.DEF
DF039Inlet air
temperature
sensor circuit110 ... CC.0/CO.1 ... ...
DF040Cylinder 1
injector circuit201 CO CC.1/CC/1.DEF ... CO
DF041Cylinder 2
injector circuit202 CO CC.1/CC/1.DEF ... CO
DF042Cylinder 3
injector circuit203 CO CC.1/CC/1.DEF ... CO
DF043Cylinder 4
injector circuit204 CO CC.1/CC/1.DEF ... CO
DF046Battery voltage 560 ... ...1.DEF/
2.DEF...
DF047Computer feed
voltage615 ... ... 1.DEF ...
DF049Refrigerant
sensor circuit530 ... ... CC.1/CO.0 ...
DF050Brake switch
circuit571 ... ...1.DEF/
2.DEF...
DF051Cruise control/
speed limiter
function575 ... ...1.DEF/
2.DEF/
3.DEF...
DF053Rail pressure
regulation
function89 3.DEFCC.0/CC.1/CO/
1.DEF/2.DEF/
4.DEF/5.DEF/
6.DEF/7.DEF... ..
DF054Turbocharging
solenoid valve
control circuit33CO/CC.0/CC.1/
1.DEF/2.DEF/
3.DEF/4.DEF/
5.DEF... ... CC.0

DIESEL INJECTION
Fault finding – Fault summary table13B
13B-28V3 MR-372-J84-13B250$270.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
Tool
faultDIAGNOSTIC
TOOL
DESCRIPTIONAssociated
DTCLEVEL 1 FAULT
WARNING
LIGHT (Orange
heater plugs On
indicator light)LEVEL 2 FAULT
WARNING
LIGHT (Red
overheating
warning light)NO
FAULT
WARNING
LIGHT ONOBD
WARNING
LIGHT ON
DF055Turbocharging
pressure
regulation circuit243 1.DEF/2.DEF ... ... ..
DF056Air flow sensor
circuit100CO.0/CC.1/
1.DEF/2.DEF... ...CO.0/CC.1/
1.DEF/
2.DEF
DF057Water in diesel
fuel detector
circuit2264 ... ... X ...
DF059Misfiring on
cylinder 1301 ... ... X ...
DF060Misfiring on
cylinder 2302 ... ... X ...
DF061Misfiring on
cylinder 3303 ... ... X ...
DF062Misfiring on
cylinder 4304 ... ... X ...
DF069Impact detected
signal1620 ... 1.DEF ... ...
DF070Clutch switch
circuit830 ... ...1.DEF/
2.DEF...
DF086Coolant pump
relay control
circuit2600 CO.0/CC.1 ... ... ...
DF091Vehicle speed
signal500 ... ...1.DEF/
2.DEF
3.DEF/
4.DEF ...
DF097Camshaft sensor
circuit340 1.DEF/2.DEF ... ... ...
DF118EGR solenoid
valve servo-
control409 2.DEF ... 1.DEF ...
DF195Camshaft/engine
speed sensor
consistency16 1.DEF ... ... ...
DF209EGR valve
position sensor
circuit486 ... ...CO.0/
CC.1/
1.DEFCO.0/CC.1/
1.DEF

DIESEL INJECTION
Fault finding – Fault summary table13B
13B-29V3 MR-372-J84-13B250$270.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
Tool
faultDIAGNOSTIC
TOOL
DESCRIPTIONAssociated
DTCLEVEL 1 FAULT
WARNING
LIGHT (Orange
heater plugs On
indicator light)LEVEL 2 FAULT
WARNING
LIGHT (Red
overheating
warning light)NO
FAULT
WARNING
LIGHT ONOBD
WARNING
LIGHT ON
DF226Damper valve
circuit638CO/CC/CC.0/
CC.1/1.DEF/
2.DEF/3.DEF... ... ...
DF250ESP function C122 ... ...1.DEF/
2.DEF...
DF272EGR valve
control circuit403 1.DEF ... 2.DEF ...
DF276Injector code
programming611 1.DEF/2.DEF ... ... ...
DF485Catalytic
converter fault
finding422 ... ... X ...
DF532Alternator
charge signal2502CC.0/CC.1/
1.DEF/2.DEF... ... ...
DF619EGR valve
jammed open2142 X ... ... ...
DF620EGR valve
fouled2141 X ... ... ...
DF621EGR valve is
jammed open
(OBD fault)2413 ... ... X X
DF652Turbine
upstream
temperature
sensor circuit242A CC.0/CO.1
DF778Turbine
upstream
temperature
control242B 1.DEF/2.DEF
DF1070Cold loop 534

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-30V3 MR-372-J84-13B250$315.mif
DF001
PRESENT
OR
STOREDCOOLANT TEMPERATURE SENSOR CIRCUIT
CC.0 : Short circuit to earth
CO.1 : Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present:
–when an attempt is made to start the engine,
–when the engine is running.
Special notes:
If the fault is present:
–the coolant temperature: PR064 Coolant temperature is fixed at 119˚C,
–the preheating phase is greater than 10 seconds,
–the low speed motor-driven fan assembly (GMV 1) is continuously supplied,
–if there is a fault with GMV 1, then start GMV 2 for vehicles with air conditioning.
–the level 1 warning light is lit,
–the OBD warning light will illuminate after three consecutive driving cycles (starting
+ 5 seconds + switching off the ignition and waiting 1 minute).
Use bornier Ele. 1681 or Ele. 1590 for all operations on the computer connectors.
Check the connections of the coolant temperature sensor 4-track connector.
Check the injection computer connections.
Repair if necessary.
Measure the resistance of the coolant temperature sensor between tracks 2 and 3 of its black connector.
Replace the sensor if its resistance is not approximately:
75780 ± 7000 Ω at - 40˚C
12460 ± 122 Ω at - 10˚C
2252 ± 112 Ω at 25˚C
811 ± 39 Ω at 50˚C
283 ± 8 Ω at 80˚C
115 ± 3 Ω at 110˚C
87 ± 2 Ω at 120˚C
Check the insulation, continuity and the absence of interference resistance on the following connections:
Injection computer brown 48-track connector B
track F2Track 3 coolant temperature sensor
Injection computer brown 48-track connector B
track H1Track 2 coolant temperature sensor
Repair if necessary.
If the fault is still present, replace the coolant temperature sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16
PROGRAM No.: C1
Vdiag No.: 51DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16_V51_DF001

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-31V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF003
PRESENT
OR
STOREDATMOSPHERIC PRESSURE SENSOR CIRCUIT
1.DEF : Signal outside upper limit
2.DEF : Signal outside lower limit
3.DEF : Inconsistent signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present:
–when an attempt is made to start the engine,
–when the engine is running.
Special notes:
The atmospheric pressure sensor is integrated into the injection computer and cannot
be separated.
If the fault is present:
–there is light smoke at the exhaust,
–the atmospheric pressure value changes to safe mode, PR035 Atmospheric
pressure = 750 mbar.
–the level 1 warning light is lit,
–the OBD warning light will come on after three consecutive driving cycles (starting
+ 5 seconds + switching off the ignition and waiting 1 minute).
Use bornier Ele. 1681 or Ele. 1590 for all operations on the computer connectors.
Disconnect the injection computer and check the condition of the contacts and connector.
Repair if necessary.
Display the value of parameter PR041 Turbocharger pressure.
If this value is stuck at 750 mbar, refer to interpretation of fault DF004 Turbocharging pressure sensor circuit.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF003

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-32V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF004
PRESENT
OR
STOREDTURBOCHARGING PRESSURE SENSOR CIRCUIT
CO.0 : Open circuit or short circuit to earth
CC.1 : Short circuit to + 12 V
1.DEF : Inconsistency of the signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present:
–when an attempt is made to start the engine,
–when the engine is running.
Special notes:
If the fault is present:
–the EGR function is inhibited,
–the turbocharging pressure sensor is in defect mode, PR041 = 750 mbar,
–the level 1 warning light is lit.
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
Order of priority in the event of more than one fault:
Deal with fault DF011 Sensor supply voltage no. 1 first if it is present or stored.
CO.0
NOTESNone
Check the turbocharger pressure sensor connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against earth of the following connections:
Injection computer brown 48-track connector B,
track G4Track 3 turbocharging pressure sensor
connector
Injection computer brown 48-track connector B,
track K2Track 4 turbocharger pressure sensor connector
Repair if necessary.
If the fault is still present, replace the turbocharging pressure sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF004

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-33V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF004
CONTINUED 1
CC.1
NOTESNone
Check the turbocharger pressure sensor connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against + 12 volts of the following connections:
Injection computer brown 48-track connector B,
track G4Track 3 turbocharging pressure sensor
connector
Injection computer brown 48-track connector B,
track D4Track 1 turbocharging pressure sensor
connector
Injection computer brown 48-track connector B,
track K2Track 4 turbocharger pressure sensor connector
Repair if necessary.
If the fault is still present, replace the turbocharging pressure sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-34V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF004
CONTINUED 2
1.DEF
NOTESNone
In the event of a combination of faults with DF003 Atmospheric pressure sensor circuit, display parameter
PR041 Turbocharging pressure.
If this value is locked at 750 mbar and PR035 Atmospheric pressure is displaying a different value, replace
the turbocharging pressure sensor.
Check the turbocharger pressure sensor connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and the absence of interference resistance of the following connections:
Injection computer brown 48-track connector B,
track G4Track 3 turbocharging pressure sensor
connector
Injection computer brown 48-track connector B,
track D4Track 1 turbocharging pressure sensor
connector
Injection computer brown 48-track connector B,
track K2Track 4 turbocharger pressure sensor connector
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-35V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF005
PRESENT
OR
STOREDENGINE SPEED SENSOR CIRCUIT
1.DEF : No signal
2.DEF : Inconsistent signal
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present:
–when an attempt is made to start the engine,
–when the engine is running.
Special notes:
Use bornier Ele. 1681 or Ele. 1590 for all operations on the computer connectors.
The engine speed sensor is consistent with the camshaft sensor.
If the fault is present:
–it is impossible to start the engine or the engine stops,
–the level 2 warning light is lit.
Check the engine speed sensor connections.
Check the injection computer connections.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that the sensor is correctly mounted and that the flywheel target is not damaged.
Check that the gap between the engine speed sensor and the flywheel is 0.5 to 1.8 mm.
Measure the resistance of the engine speed sensor between terminals A and B of its black connector.
If the winding resistance is not between 510 Ω and 850 Ω at an engine temperature of 20˚C, replace the engine
speed sensor.
Check for continuity and the absence of interference resistance of the following connections:
Injection computer brown 48-track connector B
track B1Track A engine speed sensor
Injection computer brown 48-track connector B
track C1Track B engine speed sensor
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF005

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-36V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF007
PRESENT
OR
STOREDRAIL PRESSURE SENSOR CIRCUIT
CC.0 : Short circuit to earth
CO.1 : Short circuit or open circuit to + 12 V
1.DEF : Offset at minimum threshold
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after repeated engine starts or with the engine running.
Special notes:
Use bornier Ele. 1681 or Ele. 1590 for all operations on the computer connectors.
If the fault is present:
–the engine will stop immediately,
–it is impossible to restart,
–the level 2 warning light is lit.
Priorities when dealing with a number of faults:
Deal with fault DF013 Sensor supply voltage no. 3 first, if it is present or stored.
CC.0
NOTESNone
Check the rail pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation to earth of the following connections:
Injection computer brown 48-track connector B
track G3Track 2 rail pressure sensor
Brown 48-track connector B injection computer
track A4Track 3 rail pressure sensor
Repair if necessary.
If the fault is still present, replace the rail pressure sensor and tighten to 35 ± 5 Nm.
Follow the recommended safety advice (see cleanliness advice).
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF007