check engine RENAULT SCENIC 2009 J84 / 2.G Engine And Peripherals EDC16 Service Manual

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-94V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF057
PRESENT
OR
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUIT
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Check the conformity of the fuel used by applying test 10 Diesel fuel conformity check.
Check the sealing of the tank and low pressure circuit by applying test 2 Low pressure circuit check.
A) Make sure the water in diesel fuel detection sensor is properly connected.
–If not, clear the fault,
–Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds.
–If the fault does not recur, end the fault finding procedure.
–If the fault does recur, go to step C.
B) If the water detection sensor is absent:
–Insulate the electrical connector not connected to the vehicle (risk of dampness, oxidation, and erratic
appearance of faults).
Check that the configuration reading LC065 Water detected in the diesel is NONE.
If LC065 is WITH, run command RZ005 Programming to reinitialise the vehicle configurations.
–Clear the faults.
–Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds.
–If the fault does not recur, end the fault finding procedure.
C) If the sensor is properly connected:
–Bleed the diesel filter unit (see MR 364, Mechanics, 13A, Fuel supply).
–Clear the fault.
–Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds.
–If the fault does not recur, end the fault finding procedure.
D) If the fault recurs:
–Check for continuity and the absence of interference resistance on the connection between:
Injection computer 32-track grey connector track A2 Track 3 of the water detection sensor
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF057

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-95V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF057
CONTINUED
Check the power supply to the water detection sensor:
+ 12 V after relay track 1 water detection sensor
earth track 2 water detection sensor
Carry out the necessary repairs.
If none of these checks reveal any faults:
–Replace the water detection sensor (see MR 364, Mechanics, 13A, Fuel supply).
–Clear the fault.
–Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds,
to confirm the repair.
Note:
if the level of water in the fuel filter unit is lower than the sensor electrodes, certain driving conditions (on a bend,
hill) may causethe injection warning light to light up erratically.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-96V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF059
PRESENT
OR
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present, engine performance is reduced and engine instabilities may
occur.
Priority when dealing with a number of faults:
Deal with fault DF040 Cylinder 1 injector circuit first, if it is present or stored.
Check that the IMA code of injector no. 1 has been entered correctly and that it matches the code marked on the
corresponding injector.
Enter the code to the unprogrammed/incorrectly programmed injector, if necessary.
Refer to the interpretation of commands, SC002 Entering injector codes.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
When dealing with several combustion misfire faults, check the conformity of the fuel by applying test 10 Diesel
fuel conformity check.
Visually inspect the return pipe of injector no. 1.
Repair if necessary.
If the fault is still present, carry out test 8 INCORRECT INJECTOR OPERATION.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF059

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-97V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF060
PRESENT
OR
STOREDCOMBUSTION MISFIRING ON CYLINDER 2
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present, engine performance is reduced and engine instabilities may
occur.
Priority when dealing with a number of faults:
Deal with fault DF041 Cylinder 2 injector circuit first, if it is present or stored.
Check that the IMA code of injector no. 2 has been entered correctly and that it matches the code marked on the
corresponding injector.
Enter the code to the unprogrammed/incorrectly programmed injector, if necessary.
Consult the interpretation of commands, SC002 Entering injector codes.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
When dealing with several combustion misfire faults, check the conformity of the fuel by applying test 10 Diesel
fuel conformity check.
Visually inspect the return pipe of injector no. 2.
Repair if necessary.
If the fault is still present, carry out test 8 INCORRECT INJECTOR OPERATION.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF060

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-98V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF061
PRESENT
OR
STOREDCOMBUSTION MISFIRING ON CYLINDER 3
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present, engine performance is reduced and engine instabilities may
occur.
Priority when dealing with a number of faults:
Deal with fault DF042 Cylinder 3 injector circuit first, if it is present or stored.
Check that the IMA code of injector no. 3 has been entered correctly and that it matches the code marked on the
corresponding injector.
Enter the code to the unprogrammed/incorrectly programmed injector, if necessary.
Consult the interpretation of commands, SC002 Entering injector codes.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
When dealing with several combustion misfire faults, check the conformity of the fuel by applying test 10 Diesel
fuel conformity check.
Visually inspect the return pipe of injector no. 3.
Repair if necessary.
If the fault is still present, carry out test 8 INCORRECT INJECTOR OPERATION.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF061

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-99V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF062
PRESENT
OR
STOREDCOMBUSTION MISFIRING ON CYLINDER 4
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present, engine performance is reduced and engine instabilities may
occur.
Priority when dealing with a number of faults:
Deal with fault DF043 Cylinder 4 injector circuit first, if it is present or stored.
Check that the injector no. 4 IMA code has been entered correctly and that it matches the code marked on the
corresponding injector.
Enter the code to the unprogrammed/incorrectly programmed injector, if necessary.
Consult the interpretation of commands, SC002 Entering injector codes.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
When dealing with several combustion misfire faults, check the conformity of the fuel by applying test 10 Diesel
fuel conformity check.
Visually inspect the return pipe of injector no. 4.
Repair if necessary.
If the fault is still present, carry out test 8 INCORRECT INJECTOR OPERATION.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF062

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B -100V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF069
PRESENT
OR
STOREDIMPACT DETECTED SIGNAL
1.DEF : Impact stored by the injection computer
NOTESConditions for applying the fault finding procedure to stored faults:
Only apply the procedure if the fault is present and if the vehicle does not start.
Special notes:
The fault appears when the injection computer receives a frontal impact signal from the
Airbag computer via the multiplex network.
As soon as the injection computer receives this signal:
–engine operation is prohibited,
–the level 2 warning light is lit.
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
If the vehicle has been involved in an accident:
Carry out any necessary repairs,
–clear the fault,
–switch off the ignition,
–wait for 1 minute,
–switch on the ignition,
If the fault does not recur, end the fault finding procedure.
If the fault recurs, carry out fault finding on the AIRBAG computer.
If the vehicle has not been involved in an accident:
Run fault finding on the AIRBAG computer
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF069

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B -101V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF070
PRESENT
OR
STOREDCLUTCH SWITCH CIRCUIT
1.DEF : No signal
2.DEF : Inconsistent signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the clutch pedal is depressed, or during a road test.
Special notes:
If this fault is present, the cruise control/speed limiter function will be inhibited.
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
Check the conformity and adjustment of the clutch switch (position, connection).
–display status ET405 Clutch pedal switch:
–when the clutch pedal is engaged, status ET405 should be INACTIVE,
–when the clutch pedal is disengaged, status ET405 should be ACTIVE.
If these checks are not OK, replace the clutch switch.
If the check show the correct results:
Check the connections of the clutch pedal switch.
Check the injection computer connections.
Repair if necessary.
Check continuity and make sure there is no interference resistance on the following connection:
Injection computer black 32-track connector A,
track C4Track 1 clutch pedal switch
Repair if necessary.
Check for the presence of earth on track 2 of the clutch pedal switch.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF070

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B -102V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF086
PRESENT
OR
STOREDCOOLANT PUMP RELAY CONTROL CIRCUIT
CO.0 : Open circuit or short circuit to earth
CC.1 : Short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the ignition is switched off and after a wait of 1
minute, or following a AC195 Electric coolant pump actuator command.
Special notes:
The control relay is located in the engine compartment connection unit.
If the fault is present:
–the EGR function is inhibited,
–the level 1 warning light is lit.
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
CO.0
NOTESNone
Test the electric coolant pump relay (A 20A) and check it is operating correctly.
Check the injection computer connections.
Repair if necessary.
Check the continuity between the following connections: Tracks B1 and B5 of the coolant pump relay mounting.
If the check show the correct results,
Check the continuity and insulation to earth of the following connections:
Injection computer brown 48-track connector B, track H4Track B2 of the coolant pump relay
mounting
Injection supply relay mounting, Track 5Track B1 of the coolant pump relay
mounting
Injection supply relay mounting, Track 5Track B5 of the coolant pump relay
mounting
Turbocharger bearing coolant pump connector, Track 1Track B3 of the coolant pump relay
mounting
Check for the earth on Track 2 of the turbocharger bearing coolant pump connector.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF086

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B -105V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF097
PRESENT
OR
STOREDCAMSHAFT SENSOR CIRCUIT
1.DEF : No signal
2.DEF : Inconsistent signal
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
A drop in engine speed followed by nominal behaviour from the vehicle is possible.
Special notes:
If this fault is present:
–It is impossible to start the vehicle,
–the level 1 warning light is lit.
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
1.DEF
2.DEF
NOTESCheck the conformity of the + 12 V after relay supply line,
from track 2 of the UPC PPM1 connector.
(Use the Wiring Diagrams for the vehicle)
Check the camshaft sensor connections.
Check the injection computer connections.
Check that the camshaft sensor is correctly positioned and mounted.
Also check the general condition, (damaged housing, heating up, etc.)
Carry out the necessary repairs.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF097