fuel RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection User Guide

13B-33
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF007
CONTINUED
CO.1
NOTESNone.
Check the rail pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against + 12 V of the following connections:
Injection computer brown 48-track connector B, track G3 Track 2 rail pressure sensor
Injection computer brown 48-track connector B, track C4 Track 1 rail pressure sensor
Repair if necessary.
if the fault is still present, replace the rail pressure sensor and tighten it to 35±5N.m.
Observe the safety advice in the Introduction.
1.DEF
2.DEF
NOTESNone.
Check the rail pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Check the continuity and the absence of the interference resistance of the following connections:
Injection computer brown 48-track connector B, track G3 Track 2 rail pressure sensor
Injection computer brown 48-track connector B, track A4 Track 3 rail pressure sensor
Injection computer brown 48-track connector B, track C4 Track 1 rail pressure sensor
Repair if necessary.
With the ignition on and the engine stopped for more than one minute:
Display parameter PR038 Rail pressure in the Fuel circuit, Engine management function tab.
– If the value is below 50 bar, the sensor is in order.
In this case, contact the Techline.
– If the pressure is above 50 bar, replace the rail pressure sensor and tighten it to 35 ± 5 N.m.
Observe the safety advice in the Introduction.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-66
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF053
PRESENT
OR
STORED
RAIL PRESSURE REGULATION FUNCTION
CC.1 : Short circuit to + 12 V
CC.0 : Short circuit to earth
CO : Open circuit
1.DEF : Internal electrical fault
2.DEF : Measured pressure too low
3.DEF : Measured pressure too high
4.DEF : Insufficient pressure
5.DEF : Pressure < minimum
6.DEF : Pressure > maximum
7.DEF : Extensive pump command
8.DEF : significant pump control at idle speed
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the engine.
Special notes:
If the fault is present:
– It is not possible to start the engine.
– the level 2 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the rail pressure regulator connectors.
Check the injection computer connections.
Check the low pressure circuit.
Check the conformity of the fuel used, apply test 5 Diesel fuel conformity check.
Check the injector return flow, run test 1 Injector test.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the rail pressure regulator between tracks 1 and 2.
If the resistance is not 3Ω ±1 at 20°C, replace the injection pump.
Check the continuity and insulation from + 12 V on the following connection:
Injection computer brown 48-track connector B, track M4 Track 2 of the fuel flow actuator
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V08_DF053/EDC16_V10_DF053/EDC16_V14_DF053

13B-67
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF053
CONTINUED 1
CC.0
CO
NOTESNone.
Check the fuel flow regulator connections.
Check the injection computer connections.
Check the low pressure circuit.
Check the conformity of the fuel used, apply test 5 Diesel fuel conformity check.
Check the injector return flow, run test 1 Injector test.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the flow regulator between tracks 1 and 2.
If the resistance is not 3Ω ±1 at 20°C, replace the injection pump.
Check the continuity and insulation from earth of the following connection:
Injection computer brown 48-track connector B, track M4 Track 2 of the fuel flow regulator
With the ignition on, check for + 12 V after relay feed on track 1 of the fuel flow regulator.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

13B-68
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
*Opening cyclic ratioDF053
CONTINUED 2
1.DEF
NOTESNone.
Check the rail pressure regulator connectors.
Check the injection computer connections.
Check the low pressure circuit.
Check the conformity of the fuel used, apply test 5 Diesel fuel conformity check.
Check the injector return flow, run test 1 Injector test.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the flow regulator between tracks 1 and 2.
If the resistance is not 3Ω ±1 at 20°C, replace the injection pump.
Check the continuity and absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track M4 Track 2 of the fuel flow regulator
UPC, connector PPM1, track 1 Track 1 of the rail pressure
regulator
Repair if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

13B-69
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF053
CONTINUED 3
2.DEF to
8.DEF
NOTESNone.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
In the event of rail overpressure:
Check that the injectors are operating correctly (see Component test, Test 1, Injector Test).
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator.
Display parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
If these checks do not indicate any abnormality and if the fault is still present, replace the injection pump.
in the event of rail underpressure:
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator.
Display parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
Check the low pressure diesel circuit priming.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check that there are no air bubbles between the filter and the high pressure pump.
Check the low and high pressure diesel fuel circuit sealing (visual inspections, odour, etc.): pump housing,
pressure relief valve, pipes, rail and injector unions, injector wells, etc.
Check that the injectors are operating correctly (see Component test, Test 1, Injector Test).
Carry out the necessary operations.
If the fault is still present, replace the injection pump.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

13B-78
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF057
PRESENT
OR
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUIT
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine is started or following a road test.
A) Make sure the water in diesel fuel detection sensor is properly connected.
– If not, clear the fault,
– carry out a road test (speed > 12 mph (20 km/h) at an engine speed of> 1200 rpm) for more than 30 seconds.
– If the fault does not recur, end the fault finding procedure.
– If the fault does recur, go to step B.
B) If the sensor is properly connected:
– drain the diesel filter unit (seeMR 364, 13A, Fuel supply),
– clear the fault,
– carry out a road test (speed > 12 mph (20 km/h) at an engine speed of> 1200 rpm) for more than 30 seconds.
If the fault does not recur, end the fault finding procedure.
C) If the fault recurs:
–Check the continuity and the absence of unwanted resistance on the connection between:
Injection computer, grey 32-track connector C, track A2 Track 3 of the water detection sensor
–Check the power supply to the water detection sensor:
UPC PPM1 black connector track 2 Track 1 the water detection sensor
Earth Track 2 water detection sensor
– Carry out the necessary repairs.
If none of these checks reveal any faults:
– Replace the water detection sensor (see MR 364, 13A, Fuel supply).
– Clear the fault.
– Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds,
to confirm the repair.
Note:
if the level of water in the fuel filter unit is lower than the sensor electrodes, certain driving conditions (on a bend,
leaning) may causethe injection warning light to light up erratically.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF057/EDC16_V48_DF057/EDC16_V4C_DF057

13B-85
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF097
PRESENT
OR
STOREDCAMSHAFT SENSOR CIRCUIT
1.DEF : no signal
2.DEF : inconsistent signal
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault declared present before an attempt is made to start the engine it will not be
possible to start the engine.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
1.DEF
2.DEF
NOTESPriority when dealing with a number of faults:
In the event of more than one fault:
–DF056 Air flow sensor circuit,
–DF057 Water in diesel fuel detector circuit,
–DF067 Damper control circuit,
Check the conformity of the + 12 V after relay supply line,
from track 2 of the UPC PPM1 connector.
(Use the Wiring Diagrams Technical Note for the vehicle).
Check the camshaft sensor connectors,
Check the injection computer connections.
Check that the camshaft sensor is correctly positioned and mounted.
Also check the general condition (damaged housing, heating up, etc.).
Carry out the necessary repairs.
Check the continuity and absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track D1 Track 2 Camshaft sensor
Injection computer brown 48-track connector B, track A1 Track 1 Camshaft sensor
Repair if necessary.
Check the camshaft sensor resistance between tracks 2 and 3.
If the resistance is not 10250Ω ±500 at 20°C, replace the sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF097/EDC16_V48_DF097/EDC16_V4C_DF097

13B-87
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF098
PRESENT
OR
STOREDFUEL TEMPERATURE SENSOR CIRCUIT
CC.0 : short circuit to earth
CO.1 : open circuit or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to cold start the
engine.
Special notes:
– Use bornier Ele. 1681 for all operations on the injection computer connectors.
– The default value given by the diagnostic tool is 100°C.
CC.0
NOTESNone.
Check the fuel temperature sensor connections.
Check the injection computer connections.
Repair if necessary.
Measure the resistance of the fuel temperature sensor across tracks 1 and 2.
Replace the fuel temperature sensor if the resistance is not: 2050Ω ± 100 at 25°C
810Ω ± 47 at 50°C
309 Ω ± 17 at 80°C
Check the continuity and insulation from earth of the following connections:
Injection computer brown 48-track connector B, track H2 Track 1 fuel temperature sensor
Injection computer grey 32-track connector C, track F1 Track 2 fuel temperature sensor
If the fault is still present, replace the fuel temperature sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF098/EDC16_V48_DF098/EDC16_V4C_DF098

13B-88
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF098
CONTINUED
CO.1
NOTESNone.
Check the fuel temperature sensor connections.
Check the injection computer connections.
Repair if necessary.
Measure the resistance of the fuel temperature sensor across tracks 1 and 2.
Replace the fuel temperature sensor if the resistance is not: 2050Ω ± 100 at 25°C
810Ω ± 47 at 50°C
309 Ω ± 17 at 80°C
Check the continuity and insulation against + 12 V of the following connections:
Injection computer brown 48-track connector B, track H2 Track 1 fuel temperature sensor
Injection computer grey 32-track connector C, track F1 Track 2 fuel temperature sensor
If the fault is still present, replace the fuel temperature sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.

13B-114
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
FUEL CIRCUIT
NOTESOnly carry out this conformity check after carrying out a complete check using
the diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1 Engine speed PR055: Engine speedIndicates the engine's
speed of rotation in
rpm.
Ignition on
PR055= 0rpmIn the event of a fault,
consult the interpretation
of fault DF005 Engine
speed sensor circuit.
2 Temperature PR063: Fuel
temperatureShows the fuel
temperature
Default value: 100°CIn the event of a fault,
consult the interpretation
of fault DF098 Fuel
temperature sensor
circuit.
3 PressurePR008: Rail reference
pressureIndicates the
theoretical pressure
value for optimum
engine operation
X = 250 barIn the event of a fault,
consult the interpretation
of fault DF053 Rail
pressure regulation
function.
PR048: Rail pressure
regulation valve
OCRX= 15%
In the event of a fault,
consult the interpretation
of fault DF007 Rail
pressure sensor circuit.
PR038: Rail pressureX = 0 bar
Default value:
250 bar.
PR213: Rail pressure
loop differenceX = PR008 - PR038The fuel pressure variation is
the difference between the
rail pressure and the rail
pressure setpoint. In the
event of a fault, consult
the interpretation of fault
DF007 Rail pressure
sensor circuit.