sensor RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection Owner's Manual

13B-39
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF011
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE NO. 1
1.DEF : sensor reference voltage too weak
2.DEF : sensor reference voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the
engine several times.
Special notes:
If the fault is present:
– cruise control is deactivated,
– the engine speed is limited,
–the level 1 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
The sensors connected to supply no. 1 are:
–Turbocharging pressure sensor,
–Accelerator pedal potentiometer sensor, gang 1.
To locate a faulty sensor and/or connection, disconnect one of these sensors then check whether the fault
becomes stored.
If the fault is still present, start the operation again with the other sensor.
(wait a few seconds between each disconnection to allow the computer to perform the measurement).
If the fault is stored after a disconnection, replace the faulty sensor or repair its connection.
Clear the faults created by the multiple disconnections.
If the fault is still present when both these sensors have been disconnected:
1. Check the insulation from earth of the following connections:
Injection computer brown 48-track connector B, track K2 Track 3 of the turbocharger pressure
sensor
Injection computer brown 48-track connector B, track G4 Track 1 of the turbocharger pressure
sensor
Injection computer black 32-track connector A, track G2 Track 3 of the accelerator pedal
potentiometer gang 1
Injection computer black 32-track connector A, track H2 Track 4 of the accelerator pedal
potentiometer gang 1
Repair if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF011/EDC16_V48_DF011/EDC16_V4C_DF011

13B-40
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF011
CONTINUED
2. Check the insulation from + 12 V of the following connections:
Injection computer brown 48-track connector B, track K2 Track 3 of the turbocharger pressure
sensor
Injection computer brown 48-track connector B, track D4 Track 2 of the turbocharger pressure
sensor
Injection computer black 32-track connector A, track H3 Track 5 of the accelerator pedal
potentiometer gang 1
Injection computer black 32-track connector B, track H2 Track 4 of the accelerator pedal
potentiometer gang 1
Repair if necessary.
3. Check the insulation between the following connections after disconnecting the sensors:
–tracks3 and 5 of the pedal gang 1 sensor connector.
–tracks1 and 2 of the turbocharging pressure sensor connector.
If these checks do not produce the correct results, replace the faulty sensor(s).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-41
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF012
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE No. 2
1.DEF : sensor reference voltage too weak
2.DEF : sensor reference voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the engine
several times.
Special notes:
If the fault is present:
– the EGR functions and passenger compartment heating resistance functions
are inhibited,
– the engine speed is limited,
–the level 1 warning light is lit.
– The OBD warning light will come on after three consecutive cycles
(starting + 5 seconds + switch off the ignition and wait 40 seconds).
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged. Follow the procedure described in the
Wiring Check in the Introduction. This check enables the condition and the conformity of the engine wiring
harness to be checked.
The sensors connected to supply no.2 are:
–EGR valve position sensor,
–track 2 of the accelerator pedal potentiometer sensor,
–refrigerant pressure sensor.
To locate a faulty sensor and/or connection, disconnect one of these sensors then check whether the fault
becomes stored.
If the fault is still present, repeat the operation with the other sensors.
(wait a few seconds between each disconnection to allow the computer to perform the measurement).
If the fault is stored after a disconnection, replace the faulty sensor or repair its connection.
Clear the faults created by the multiple disconnections.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF012/EDC16_V48_DF012/EDC16_V4C_DF012

13B-42
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF012
CONTINUED
If the fault is still present when the three sensors have been disconnected:
1. Check the insulation from earth of the following connections:
Injection computer brown 48-track connector B, track F4 Track 2 of the EGR valve connector
Injection computer brown 48-track connector B, track J2 Track 6 of the EGR valve connector
Injection computer black 32-track connector A, track F2 Track 2 of the accelerator pedal
potentiometer gang 2
Injection computer black 32-track connector A track F3 Track 1 of the accelerator pedal
potentiometer gang 2
Injection computer, brown 48-track connector B, track F3 Track B of the refrigerant pressure
sensor
Injection computer, brown connector B track F1 Track C of the refrigerant pressure
sensor
Repair if necessary.
2. Check the insulation from + 12 V of the following connections:
Injection computer brown connector B track F4 Track 2 of the EGR valve connector
Injection computer brown connector B, track J2 Track 6 of the EGR valve connector
Injection computer grey connector C track C2 Track 4 of the EGR valve connector
Injection computer black connector A track F2 Track 2 of the accelerator pedal
potentiometer gang 2
Injection computer black connector A track F3 Track 1 of the accelerator pedal
potentiometer gang 2
Injection computer black connector A track F4 Track 6 of the accelerator pedal
potentiometer gang 2
Injection computer brown connector B track F3 Track B of the refrigerant pressure sensor
Injection computer, brown connector B track F1 Track C of the refrigerant pressure sensor
Injection computer grey connector C track C3 Track A of the refrigerant pressure sensor
Repair if necessary.
3. Check the insulation between the following connections after disconnecting the sensors:
–tracks2 and 6 of pedal sensor gang 2 connector.
–tracks2 and 4 of the EGR valve position sensor connector.
–tracksA and B of the refrigerant pressure sensor.
If these checks do not produce the correct results, replace the faulty sensor(s).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-43
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF013
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE No. 3
1.DEF : sensor reference voltage too weak
2.DEF : sensor reference voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the
engine several times.
Special notes:
If the fault is present:
– the EGR function is inhibited,
– the engine speed is limited,
–the level 2 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
The sensors connected to supply no. 3 are:
–Rail Pressure Sensor
–Air flow sensor..
To locate a faulty sensor and/or connection, disconnect one of these sensors then check whether the fault
becomes stored.
If the fault is still present, start the operation again with the other sensor.
(wait a few seconds between each disconnection to allow the computer to perform the measurement).
If the fault is stored after a disconnection, replace the faulty sensor or repair its connection.
Clear the faults created by the multiple disconnections.
If the fault is still present when both these sensors have been disconnected:
1. Check the insulation from earth of the following connections:
Injection computer brown 48-track connector B, track G3 Track 2 of the rail pressure sensor
Injection computer brown 48-track connector B, track A4 Track 3 of the rail pressure sensor
Injection computer brown 48-track connector B, track G1 Track 5 of the air flowmeter
Injection computer brown 48-track connector B, track B4 Track 3 of the air flowmeter
Injection computer brown 48-track connector B, track E2 Track 2 of the air flowmeter
Repair if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF013/EDC16_V48_DF013/EDC16_V4C_DF013

13B-44
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF013
CONTINUED
2. Check the insulation from + 12 V of the following connections:
Injection computer brown 48-track connector B track G3 Track 2 of the rail pressure sensor
Injection computer brown 48-track connector B, track A4 Track 3 of the rail pressure sensor
Injection computer brown 48-track connector B, track C4 Track 1 rail pressure sensor
Injection computer brown 48-track connector B, track G1 Track 5 of the air flowmeter
Injection computer brown 48-track connector B, track B4 Track 3 of the air flowmeter
Injection computer brown 48-track connector B, track E2 Track 2 of the air flowmeter
Injection computer brown 48-track connector B, track L4 Track 6 of the air flowmeter
Repair if necessary.
3. Check the insulation between the following connections after disconnecting the sensors:
–tracks1 and 3 of the rail pressure sensor,
–tracks2 and3 of the air flow sensor connector.
If these checks do not produce the correct results, replace the faulty sensor(s).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-52
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF039
PRESENT
OR
STOREDINLET AIR TEMPERATURE SENSOR CIRCUIT
CO.1 : open circuit or short circuit to + 12 V
CC.0 : short circuit to earth
1.DEF : below minimum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after an attempted start, or with the engine running
following a road test.
Special notes:
If the fault is present:
– The air temperature value enters defect mode, i.e. PR059 Intake air
temperature = 20°C.
– The EGR function is inhibited.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
CO.1
NOTESNone.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity of the following connection:
Air flowmeter black 6-track connector track 4 Track 2 UPC black connector
Repair if necessary.
Check the continuity and insulation against + 12 V of the following connections:
Injection computer brown 48-track connector B, track G2 Track 1 air flowmeter connector
Injection computer brown 48-track connector B, track E2 Track 2 air flowmeter connector
Repair if necessary.
Measure the air temperature sensor resistance between tracks 1 and 2 of the air flow sensor.
Replace the air flowmeter if the resistance is not: 3714Ω ±161 at + 10°C
2488 Ω ± 90 at 20°C
1671 Ω ± 59 at 30°C
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF039/EDC16_V48_DF039/EDC16_V4C_DF039

13B-53
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF039
CONTINUED 1
CC.0
NOTESNone.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against earth of the following connections:
Injection computer brown 48-track connector B, track G2 Track 1 air flowmeter
Air flowmeter black 6-track connector track 4 Track 2 UPC black connector
Injection computer brown 48-track connector B, track B4 Track 3 air flowmeter
Repair if necessary.
Measure the resistance of the air temperature sensor integrated into the flowmeter across tracks 1 and 2.
Replace the air flowmeter if the resistance is not: 3714Ω ±161 at + 10°C
2488 Ω ± 90 at 20°C
1671 Ω ± 59 at 30°C
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-54
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF039
CONTINUED 2
1.DEF
NOTESNone.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track E2 Track 2 air flowmeter
Injection computer brown 48-track connector B, track G2 Track 1 air flowmeter
Repair if necessary.
Measure the resistance of the air temperature sensor integrated into the flow sensor between tracks 1 and 2.
Replace the air flowmeter if the resistance is not: 3714Ω ±161 at + 10°C
2488 Ω ± 90 at 20°C
1671 Ω ± 59 at 30°C
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-61
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF049
PRESENT
OR
STOREDREFRIGERANT SENSOR CIRCUIT
CC.1 : short circuit to + 12 V
CO.0 : open circuit or short circuit to earth
NOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor feed voltage no. 2 first if it is present or stored.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test, or if the air conditioning is
switched on.
Special notes:
If the fault is present, air conditioning is not authorised.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the refrigerant pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Connect an air conditioning filling station (equipped with a high pressure gauge) to the vehicle.
Display parameter PR037 Refrigerant pressure and compare the value displayed by the filling station.
If the values match, carry out a fault finding procedure as described in the fault finding note for that vehicle.
If the values do not match, check the continuity and insulation against + 12 V of the following connections:
Injection computer, brown 48-track connector B, track F1 Track C refrigerant sensor
connector
Injection computer, brown 48-track connector B, track F3 Track B refrigerant sensor
connector
Injection computer grey 32-track connector C, track C3 Track A refrigerant sensor
connector
Repair if necessary.
If the fault is still present, replace the refrigerant pressure sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF049/EDC16_V48_DF049/EDC16_V4C_DF049