RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Workshop Manual

13B-191
MR-372-J84-13B200$504.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET205
ET206
ET207
THERMOPLUNGER NO. 1, 2, 3 RELAY CONTROL
STATUS DEFINITIONACTIVE: This status indicates that the control of thermoplunger relay no. 1, no.2 and
no. 3 is active.
INACTIVE: This status indicates that the control of thermoplunger relay no. 1, no.2 and
no. 3 is not active.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVE
Statuses ET205, ET206, ET207 are ACTIVE when:
– the engine has been started,
– and the engine coolant temperature is low (< 15°),
– and the air temperature is low (< 5°).
This program allows the engine coolant to be heated and to enable the passenger
compartment to be heated.
To control the operation of the thermoplunger relays, run the following commands:
– AC063 Heating element no.1 relay.
– AC064 Heating element no.2 relay.
– AC031 “Heating element relay no.3”.
In the event of a fault, refer to the interpretation of faults:
– DF032 “Thermoplunger no. 1 relay control circuit”
– DF033 “Thermoplunger no. 2 relay control circuit”
– DF034 “Thermoplunger no. 3 relay control circuit”.
INACTIVEStatuses ET205, ET206 and ET207 are INACTIVE with the ignition on and the engine
stopped, or when the engine is warm.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET205/EDC16_V58_ET205/EDC16_V5C_ET205/EDC16_V18_ET205/EDC16_V1C_ET205/EDC16_V20_ET205/
EDC16_V50_ET206/EDC16_V58_ET206/EDC16_V5C_ET206/EDC16_V18_ET206/EDC16_V1C_ET206/EDC16_V20_ET206/
EDC16_V50_ET207/EDC16_V58_ET207/EDC16_V5C_ET207/EDC16_V18_ET207/EDC16_V1C_ET207/EDC16_V20_ET207 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C

13B-192
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET238
SYNCHRONISATION
STATUS DEFINITIONCompleted: This status indicates that synchronisation has been carried out.
Not completed: This status indicates that synchronisation is not complete.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
WARNING
Synchronisation is carried out during the engine starting phase. This is established between the camshaft position
sensor and the Top Dead Centre sensor.
Once this synchronisation has been carried out, it enables the computer to identify cylinder no. 1 and to calculate
the precise position of the cylinder's Top Dead Centre.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
COMPLETED
Synchronisation is carried out during the engine starting phase.
Cylinder no.1 is indicated and the synchronisation will be performed once the engine is
started.
Status ET238 is COMPLETED.
If after several attempts to start the engine, status ET238 remains NOT COMPLETED,
refer to the interpretation of the following faults:
– DF005 Engine speed sensor circuit.
– DF097 Camshaft sensor circuit.
If the engine does not start, consult ALP2 Starting faults (see Fault finding chart).
NOT PERFORMEDWhen the engine is stopped but the ignition switched on, cylinder no. 1 is no longer
indicated.
Status ET238 is NOT PERFORMED: synchronisation between the crankshaft and the
camshaft has not been carried out.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET238/EDC16_V58_ET238/EDC16_V5C_ET238/EDC16_V18_ET238/EDC16_V1C_ET238/EDC16_V20_ET238

13B-193
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET341
IMMOBILISER CODE PROGRAMMED
STATUS DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
YES
Status ET341 becomes YES if dialogue is established between the UCH and the
injection computer and the card code is recognised.
Engine starting authorisation is only given if the code is recognised by the UCH
computer, and status ET003 Engine immobiliser is INACTIVE.
NOThe code remains NO if dialogue between the UCH and the injection computer is not
possible. Status ET003 Engine immobiliser is ACTIVE.
The cause of the malfunction may be incorrect card programming (see 87B,
Passenger compartment connection unit); in this case, refer to the Technical Note
for the UCH and follow the card programming procedure.
If it is not caused by the card codes, carry out a multiplex network test (if the previous
fault finding check was by function), and check that dialogue is established between the
UCH, the Protection and Switching Unit and the injection computer.
If dialogue is not established, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET341/EDC16_V58_ET341/EDC16_V5C_ET341/EDC16_V18_ET341/EDC16_V1C_ET341/EDC16_V20_ET341

13B-194
MR-372-J84-13B200$540.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET405
CLUTCH PEDAL SWITCH
STATUS DEFINITION"Inactive": this status indicates that the switch is released.
"Active": this status indicates that the switch is pressed.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
The clutch pedal is present depending on the gearbox type.
ACTIVE and clutch
pedal released
INACTIVE and
clutch pedal
depressed
Check the condition and fitting of the clutch pedal switch,
Remove the clutch pedal switch and check that it is functioning correctly.
Continuity between
connectionsInsulation between
connections
Switch pressed (Clutch
pedal released)MAM and 86D
Switch released (Clutch
pedal depressed)MAM and 86D
Replace the switch if necessary.
Check the condition and fitting of the clutch pedal switch,
Check the continuity and the absence of interference resistance on connection 86D
between components 120 and 675.
If the connection or connections are defective and there is a repair method (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check for an earth on connection MAM of the clutch switch.
Repair if necessary.
Remove the clutch pedal switch and check that it is functioning correctly.
Continuity between
connectionsInsulation between
connections
Switch pressed (Clutch
pedal released)MAM and 86D
Switch released (Clutch
pedal depressed)MAM and 86D
Replace the clutch pedal switch if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET405/EDC16_V58_ET405/EDC16_V5C_ET405/EDC16_V18_ET405/EDC16_V1C_ET405/EDC16_V20_ET405 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$540.mif

13B-195
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CRUISE CONTROL/SPEED LIMITER DEACTIVATION
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system operation
programming.
Note:
Cruise control can be activated when the vehicle speed exceeds 20 mph (30 km/h).
Status ET415 shows various factors that cause deactivation of the cruise control/speed limiter function, due to a
driver request or the external environment (eg. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ007 Fault memory, to reset this status to WITHOUT.
NONE
This status is present on the diagnostic tool if:
the computer has been reinitialised,
the computer has been reprogrammed.
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving, with cruise control active (ET042:
Cruise control/Speed limiter: CRUISE CONTROL) and upon a traction control
request.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 1 without a traction control request (see38C, ABS).
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes "STATUS 2" when driving with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No 1 and No 2.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET415/EDC16_V58_ET415/EDC16_V5C_ET415/EDC16_V18_ET415/EDC16_V1C_ET415/EDC16_V20_ET415

13B-196
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 1
STATUS 3
Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405: "Clutch pedal".
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical definition and, in particular, the automatic gearbox
computer configuration (see 88B, Multiplex).
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button is
pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active
– and the driver presses the 0 button.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 4 without pressing the 0 button, refer to the
interpretation of status ET703 Cruise control/speed limiter buttons and test the R/0
control button located on the right-hand side of the steering wheel.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-197
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 2
STATUS 5
Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal indicating that the brake pedal switch has been
pressed.
If status ET415 is STATUS 5, refer to the interpretation of:
– of status ET042 Cruise control/speed limiter,
– of status ET703 Cruise control/speed limiter buttons,
– of status ET704 Brake contact no. 1,
– and status ET705 Brake contact No 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check for any faults on the
diagnostic tool relating to this component. Deal with them if necessary.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 changes to "STATUS 5", deal with present faults or those stored in the
injection computer.
If the fault is still present, contact Techline.
STATUS 6Gear lever in neutral (manual gearbox) or the neutral position (automatic
gearbox)
Status ET415 becomes STATUS 6 when driving with cruise control active (ET042
"Cruise control/speed limiter": CRUISE CONTROL) and:
– If the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is in neutral on an automatic gearbox.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on a
manual gearbox without declutching, or into neutral on an automatic transmission, test
the ABS computer and check the configuration of the tyre size stored in the computer. If
the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-198
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 3
STATUS 7
Inconsistency between the request and the vehicle speed
Status ET415 changes to STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/ speed
limiter: CRUISE CONTROL) and when there is a significant difference.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 changes to STATUS 7 where there is no significant difference in the
levels, contact the Techline.
STATUS 8Automatic transmission in defect mode.
Status ET415 becomes STATUS 8 when driving with the cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the automatic transmission is
in defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the automatic transmission
computer.
Deal with any present or stored faults (see 23A, Automatic transmission,
interpretation of faults).
Clear the automatic transmission computer fault memory by running command RZ007
"Fault memory".
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If STATUS 8 is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-199
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 9
Vehicle speed monitoring
Status ET415 changes to STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the ABS computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system,
interpretation of faults).
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 9 continues, contact the Techline.
STATUS 10Monitoring by injection computer
Status ET415 becomes "STATUS 10" when driving with cruise control active (ET042
"Cruise control/speed limiter": CRUISE CONTROL) if the injection computer detects
a fault anywhere in the engine management system, or an engine speed that is too high
or too low.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection computer.
Deal with present or stored faults.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 10 continues, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-200
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
EGR PROGRAMMING CUT-OFF
STATUS DEFINITIONThis status indicates the EGR valve programming cut-off.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
NONE
No EGR cut-off, the EGR valve is working properly in accordance with the
computer programs.
STATUS 1, 5, 6, 7, 9,
10, 12, 13, 15, 19
23, 24Switch off the ignition and wait 1 minute.
Switch the ignition on and check for faults.
Check the engine battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much and reach an engine speed that is too high.
STATUS 3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal (ET405 "Clutch pedal switch") is not pressed and that the
vehicle has stopped completely.
STATUS 4, 17Test the present and stored faults and repair.
STATUS 8Reset the EGR offsets by referring to the interpretation of command SC036
"Reinitialise programming" and select "EGR valve".
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET651/EDC16_V58_ET651/EDC16_V5C_ET651/EDC16_V18_ET651/EDC16_V1C_ET651/EDC16_V20_ET651