oil temperature RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 User Guide

13B-387
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP4
CONTINUED
is the engine running on all cylinders?
Check the operation of the injectors, run test 10 Poor injector operation.
If the fault is still present
Check the conformity of the accelerator pedal position sensor, the brake pedal sensor, the atmospheric pressure
sensor, the exhaust gas recirculation valve, and the damper valve (see Interpretation of statuses and
Interpretation of parameters).
Check the consistency of the signal for the air flowmeter, the engine coolant temperature sensor, the fuel
temperature sensor and the engine speed.
Check the connectors, the continuity, and the absence of interference resistance of the air flowmeter (apply DF056
Air flow sensor circuit), the engine coolant temperature sensor (apply DF001 Coolant temperature circuit), the
fuel temperature sensor (apply DF098 Fuel temperature sensor circuit), and the engine speed (apply DF195
Camshaft sensor - engine speed consistency).
Check:
– That the diesel filter is not clogged.
– That there are no leaks on the high and low pressure diesel circuits: run test 3 Low pressure circuit check.
– The connection of the oil vapour rebreathing circuit.
– The rail pressure regulator (MPROP) (jammed - stuck), apply the interpretation of command AC011 Rail
pressure regulator.
Check the engine timing (and the position of the high pressure pump sprocket). See the procedure in the
Workshop Repair Manual if necessary.
Test the high pressure fuel circuit:
Run the scenario SC035 High pressure fuel circuit fault finding (see Interpretation of commands).
If the fault is still present, contact the techline.
A
NO
YES
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-414V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST8 Temperature upstream of turbine too low
Perform a complete fault finding of the injection
computer using the diagnostic tool.
Is a stored or present fault indicated by the diagnostic
tool?Apply the procedure for dealing with the
associated faults.
Run test 4 Turbocharged air inlet circuit check
Is the inlet circuit in order?
Repair then carry out another particle filter
regeneration.
Check that there are no leaks or blockages
in the exhaust pipe,
Repair if necessary
Run command SC017 Regenerate
particle filter (see Interpretation of
commands).
– If the second regeneration is successful,
it is essential to change the engine oil
and replace the oil filter.
– If the second regeneration fails, contact
the Techline. Apply test 5 Air flowmeter
Is the air flow sensor correct?
Run test 6 Turbocharger control solenoid valve
check,
If the turbocharger control solenoid valve is correct, run
test 7 Turbocharger.
Is the turbocharger in order?
Apply test 10 Poor injector operation.
Are the injectors correct?
Apply test 1 Exhaust pipe check
Is the exhaust pipe in order?
Contact the Techline.
YES
NO
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
EDC16C36_V48_TEST8/EDC16C36_V50_TEST8/EDC16C36_V58_TEST8
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-417V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST10
CONTINUED 1
CASE No. 2: If at least one of the values is less than or equal to - 5 mg/st
– Check the valve clearance.
– Check the level and condition of the engine oil.
– Remove the injector with the largest adjustment.
– If there is contamination via the diesel, check the condition of the cylinder concerned (cylinder, piston, valves).
Use an endoscope if possible.
– Replace only the removed injector, and modify the IMA code using the command SC002 Enter injector codes
(see Interpretation of commands).
–Apply Part B Confirmation of flow correction fault finding for each injector (individual correction) to
confirm the fault finding.
CASE No. 3: If at least one of these values does not stabilise (20 seconds after starting)
– Check the low pressure circuit with test 3: Low pressure circuit check.
– Check the conformity of the fuel by running test 11 Diesel fuel conformity check.
Apply Part B Confirmation of flow correction fault finding for each injector (individual correction) to confirm
the fault finding.
CASE No. 4: If the fuel flow correction values are all correct (between - 5 mg/st and + 5 mg/st)
Apply Part C Measure return fuel flow.
IMPORTANT
When removing/refitting an injector, follow the cleanliness guidelines and safety advice (see MR 364 (Mégane II)
or 370 (Scénic II), Mechanical systems 13B, Diesel injector: Removal - Refitting).
Section B: Confirmation of flow correction fault finding for each injector (individual correction):
Clear the faults and perform a test with the engine idling during at least 5 min, fuel temperature> 50°C.
Check that no fault appears on the CLIP diagnostic tool and that the correction values do not reach ±5 mg/st to
confirm the repair.
If the customer complaint is still present and the fuel flow correction values are between -5 mg/st and +5 mg/st,
apply part A Fuel regulation balance check for each injector (individual), CASE No. 4.
If one or more cylinders has a flow correction value per injector that reaches ±5 mg/st, apply Part A Fuel
regulation balance check for each injector (individual) because one or more injectors might be defective.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-427V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST11
CONTINUED 1
Weigh the diesel fuel and note the fuel weight after subtracting the weight of the empty plastic cup and its cover.
Does the fuel weight fall between the minimum and maximum weights given in the table below?
Calculated weight (g.)
Fuel temperature
(°C)
Min. weight Max. weight
821 846 13
821 846 14
820 845 15
819 844 16
819 844 17
818 843 18
817 842 19
816 841 20
816 841 21
815 840 22
814 839 23
814 839 24
813 838 25
Check the fuel temperature by immersing a thermometer in the plastic cup.
End of test. The fuel is not correct.
If the fuel weight is less than the minimum value then there is petrol in the diesel fuel.
If the fuel weight is greater than the maximum value then there is oil in the diesel fuel.
Drain the fuel circuit, including the tank (see MR 364 (Mégane II ph2), Mechanical,
19C, Tank, Fuel tank: Draining, or MR 370 (Scénic II ph2), Mechanical, 19C,
Tank, Draining the fuel tank).
YESNO
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.