particle filter replacement RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 User Guide

13B-363
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC036REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the injectors
– the EGR valve,
– the damper valve,
– after particle filter replacement (Vdiag 48, 50 only),
– after particle filter regeneration with the diagnostic tool (VDiag 48, 50 only),
– after replacing the injection computer with no save option (VDiag 48, 50 only).
Ignition on and engine stopped.
To run this command, in the CLIP tool, select scenario SC036 Reinitialise programming.
Procedure to be followed:
– on the main screen, select the component to reinitialise after a mechanical operation (removal - refitting or
replacement of component),
–select YES then OK to begin reinitialisation,
–select end on the configuration completed screen to return to the main screen,
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16 C36, check the tool connection and the computer supply. before switching on
the ignition again.
End of procedure.
EDC16C36_V44_SC036/EDC16C36_V4C_SC036/EDC16C36_V48_SC036/EDC16C36_V50_SC036/EDC16C36_V54_SC036/
EDC16C36_V58_SC036EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-364
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC036
CONTINUED
Features of the selections: After particle filter regeneration with diagnostic tool and After replacement of the
particle filter:
After using one of these 2 commands:
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
–Then switch on the ignition again and clear the present or stored faults from the computer memory
(operation to be carried out within 3 minutes of switching on the ignition).
– Check the weight of soot: PR383 Weight of soot in the particle filter.
– If PR383
≥ 1 g. Apply test procedure 12 Manual clearing of the weight of soot.
IMPORTANT
When reinitialising injectors, do not forget that cylinder no. 1 is located at the flywheel end.

13B-429V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST12 Manual clearing of weight of soot
Note: In certain cases, this procedure is to be carried out only after replacement of the particle filter or after an
After-sales regeneration of the particle filter.
– Start the engine.
– Raise the engine coolant temperature.
– Read the coolant temperature with the PR064 Coolant temperature until a value greater than 65ºC is obtained.
– Accelerate the engine to 4000 rpm and maintain this speed for 5 minutes.
–After 5 minutes, release the accelerator and stop the engine.
– Switch on the ignition.
– Run command SC036 Reinitialise programming and select After particle filter replacement or After particle
filter regeneration (as appropriate).
– Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
– Then switch on the ignition again and clear the present or stored faults from the computer memory (operation
to be carried out within 3 minutes of switching on the ignition).
EDC16C36_V44_TEST12/EDC16C36_V4C_TEST12/EDC16C36_V48_TEST12/EDC16C36_V50_TEST12/EDC16C36_V54_TEST12/
EDC16C36_V58_TEST12EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.