warning RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Repair Manual

13B-183
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF647
PRESENT
OR
STOREDEGR VALVE POSITION REGULATION1.DEF: Inconsistent EGR 1 offset
2.DEF: Offset too high: valve clogged, stuck open or abnormal
3.DEF: Inconsistent EGR 3 offset
4.DEF: Above maximum threshold
5.DEF: Valve jammed closed
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the engine is started,
– a road test.
Special notes:
If the fault is present:
–the level 1 warning light is illuminated for 1.DEF, 3.DEF and 5.DEF,
–the European On Board Diagnostic warning light is illuminated for 2.DEF and
4.DEF,
– the EGR function and turbocharging are inhibited by the engine management
computer,
– engine torque is limited.
Use bornier Ele. 1681 for all operations on the engine management computer
connector.
If faults DF647 and DF038 Computer are displayed at the same time, deal with DF038
Computer first. Then check that the EGR valve is open during idling to make sure that
the programming has not been lost. If the valve does not open, carry out the
programming phase.
Priorities when dealing with a number of faults:
– DF209 EGR valve position sensor circuit,
– DF046 Battery voltage,
– DF012 Sensor supply voltage no. 2,
– DF272 EGR valve control circuit,
if they are present or stored.
For EGR valves with a flat connector, it is not possible to check the sensor resistance.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF647/EDC16C36_V4C_DF647/EDC16C36_V48_DF647/EDC16C36_V50_DF647/EDC16C36_V54_DF647/
EDC16C36_V58_DF647EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-187
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF778
PRESENT
OR
STOREDTURBINE UPSTREAM TEMPERATURE REGULATION
1.DEF: Positive loop deviation
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present after starting the engine.
Priorities when dealing with a number of faults:
Deal with faults DF652 Turbine upstream temperature sensor circuit and DF226
Damper valve circuit first, if they are present or stored.
Special notes:
If the fault is present:
–The level 1 warning light is illuminated.
– A loss of engine performance will be perceived.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V48_DF778/EDC16C36_V50_DF778/EDC16C36_V58_DF778EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-190
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF891
PRESENT
OR
STOREDGROUP 1 INJECTORS FEED
1.DEF: Faulty connections
2.DEF: Short-circuit on earth or short-circuit on +12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault becomes present after:
– the ignition is switched on,
– the engine is started.
Priority when dealing with a number of faults:
Deal with faults DF026 Cylinder 1 injector control circuit, DF027 Cylinder 2
injector control circuit, DF028 Cylinder 3 injector control circuit and DF029
Cylinder 4 injector control circuit first, if they are present or stored.
Special notes:
If the fault is present:
–the level 2 injection warning light is illuminated,
– the engine stops.
Use bornier Elé. 1681 for all operations on the engine management computer
connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF891/EDC16C36_V4C_DF891/EDC16C36_V48_DF891/EDC16C36_V50_DF891/EDC16C36_V54_DF891/
EDC16C36_V58_DF891EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-192
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF892
PRESENT
OR
STOREDGROUP 2 INJECTORS FEED
1.DEF: Faulty connections
2.DEF: Short-circuit on earth or short-circuit on +12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault becomes present after:
– the ignition is switched on,
– the engine is started.
Priority when dealing with a number of faults:
Deal with faults DF026 Cylinder 1 injector control circuit, DF027 Cylinder 2
injector control circuit, DF028 Cylinder 3 injector control circuit and DF029
Cylinder 4 injector control circuit first if they are present or stored.
Special notes:
If the fault is present:
–the level 2 injection warning light is illuminated,
– the engine stops.
Use bornier Elé. 1681 for any operations on the connectors of the engine management
computer.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF892/EDC16C36_V4C_DF892/EDC16C36_V48_DF892/EDC16C36_V50_DF892/EDC16C36_V54_DF892/
EDC16C36_V58_DF892EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-195
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
* diff: differential
DF953
PRESENT
OR
STOREDPARTICLE FILTER ABSENT
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– blue/white smoke and black particles coming from the exhaust,
the OBD warning light will illuminate after three consecutive driving cycles (start + 5
seconds, switch off the ignition and wait 40 seconds).
Priorities when dealing with a number of faults:
– DF315 Particle filter diff.* pressure sensor if present or stored
IMPORTANT
In the long term, this fault may lead to premature wear and a greater risk of
turbocharger failure.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V48_DF953/EDC16C36_V50_DF953/EDC16C36_V58_DF953EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-201
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
*ADAC: Trip Computer
DF1020
PRESENT
OR
STOREDENGINE OIL DILUTION
1. DEF: Above maximum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the engine is started.
– a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited.
Use bornier Elé. 1681 for any operations on the injection computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Note:
This fault is activated in case of considerable oil dilution due to a significant number of particle filter regenerations.
Carry out the following:
– An oil change (see MR 364 (Mégane II) or MR 370 (Scénic II), Mechanical, 10A Engine and peripherals,
Engine oil: Draining – Filling),
– reset the oil wear meter,
– clear the faults.
Reset the oil wear meter after the oil change:
It will be necessary to reinitialise the display of the trip computer.
With the ignition on:
– hold down the TC* button for 5 s.
Re-initialisation has worked when the on-board computer no longer displays the key.
If this is not the case, restart the procedure.
Specific case:
If an oil change is performed before the oil service interval warning is exceeded, reinitialise the display.
EDC16C36_V50_DF1020/EDC16C36_V58_DF1020EDC16 C36
Program No.: 91
Vdiag No.: 50, 58

13B-217V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042CRUISE CONTROL/SPEED LIMITER
STATUS DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the main On/Off switch of the cruise control/speed
limiter is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
INACTIVENo button has been pressed.
SPEED LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROL
The cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
EDC16C36_V44_ET042/EDC16C36_V4C_ET042/EDC16C36_V48_ET042/EDC16C36_V50_ET042/EDC16C36_V54_ET042/
EDC16C36_V58_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-257V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
* Regen: regeneration
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751STORED REGEN. REQUEST STATUS No. 1
STORED REGEN. REQUEST STATUS No. 2
STORED REGEN. REQUEST STATUS No. 3
STORED REGEN. REQUEST STATUS No. 4
STORED REGEN. REQUEST STATUS No. 5
STORED REGEN. REQUEST STATUS No. 6
STORED REGEN. REQUEST STATUS No. 7
STORED REGEN. REQUEST STATUS No. 8
STORED REGEN. REQUEST STATUS No. 9
STORED REGEN. REQUEST STATUS No. 10
STATUS DEFINITIONStatuses ET742 to ET751 correspond to the causes for the regeneration request. They
are connected to parameters PR816 Stored regeneration start No. 1 to PR825
Stored regeneration start No. 10 which contains the stored mileage of the vehicle at
the start of the regeneration (for example, PR745 Store regeneration start No. 4 is
related to ET709 Store regen.* request status No. 4).
NOTESSpecial notes:
For Vdiag 48:
These statuses should only be interpreted for ALP11 Particle filter warning light
comes on too frequently.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS 1Request by weight of soot
Regeneration has been requested after the maximum weight of soot has been
reached and measured in the particle filter, without the particle filter warning light
coming on.
EDC16C36_V48_ET742/EDC16C36_V48_ET743/EDC16C36_V48_ET744/EDC16C36_V48_ET745/EDC16C36_V48_ET746/
EDC16C36_V48_ET747/EDC16C36_V48_ET748/EDC16C36_V48_ET749/EDC16C36_V48_ET750/EDC16C36_V48_ET751/
EDC16C36_V50_ET742/EDC16C36_V50_ET743/EDC16C36_V50_ET744/EDC16C36_V50_ET745/EDC16C36_V50_ET746/
EDC16C36_V50_ET747/EDC16C36_V50_ET748/EDC16C36_V50_ET749/EDC16C36_V50_ET750/EDC16C36_V50_ET751/
EDC16C36_V58_ET742/EDC16C36_V58_ET743/EDC16C36_V58_ET744/EDC16C36_V58_ET745/EDC16C36_V58_ET746/
EDC16C36_V58_ET747/EDC16C36_V58_ET748/EDC16C36_V58_ET749/EDC16C36_V58_ET750/EDC16C36_V58_ET751
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-258V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
* Regen: regeneration
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751
CONTINUED
STATUS 2
Request by estimated weight of soot
Regeneration has been requested following an estimate of the maximum weight of
soot in the particle filter, without the particle filter warning light coming on.
STATUS 3Request by distance travelled
Regeneration has been requested because the distance travelled since the last
successful regeneration has reached the maximum authorised value (the particle filter
warning light has not illuminated).
STATUS 4Request by number of regeneration failures or weight of soot
This status corresponds to the appearance of DF312 Speed request.
This corresponds to the maximum number of failed regenerations or to the maximum
weight of soot in the particle filter, with illumination of the particle filter warning light.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-341V9 MR-372-J84-13B450$152.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR784
PR785
PR786
PR787
PR788
PR789
PR790
PR791
PR792
PR793DF312 RECORD NO. 1
DF312 RECORD NO. 2
DF312 RECORD NO. 3
DF312 RECORD NO. 4
DF312 RECORD NO. 5
DF312 RECORD NO. 6
DF312 RECORD NO. 7
DF312 RECORD NO. 8
DF312 RECORD NO. 9
DF312 RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
These parameters must only be interpreted for DF312 Speed request if it is present
or stored.
These parameters exist only in Vdiag48.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C, without electrical consumers
In the event of a fault, consult the interpretation of fault DF312 Speed request.
These parameters are used for looking up the history of the last ten particle filter warning light activations
Each parameter from PR784 to PR793 contains a record of the vehicle mileage when the particle filter warning
light illuminates. The appearance of fault DF312 Speed request is associated with each of these parameters.
PR784 to PR793 operate through successive copying (when the particle filter warning light comes on, the value of
PR784 is copied to PR785, the value of PR785 is copied to PR786 and so on).
When there are more than ten records, the value of PR793 DF312 record no. 10 is cleared. The new mileage is
allocated to PR784.
If none of the parameters between PR784 and PR793 is available in the sub-function, this means that no data has
been saved. The parameters appear in the sub-function when they have a value above zero.
EDC16C36_V48_PR784/EDC16C36_V48_PR785/EDC16C36_V48_PR786/EDC16C36_V48_PR787/EDC16C36_V48_PR788/
EDC16C36_V48_PR789/EDC16C36_V48_PR790/EDC16C36_V48_PR791/EDC16C36_V48_PR792/EDC16C36_V48_PR793/
EDC16C36_V58_PR784/EDC16C36_V58_PR785/EDC16C36_V58_PR786/EDC16C36_V58_PR787/EDC16C36_V58_PR788/
EDC16C36_V58_PR789/EDC16C36_V58_PR790/EDC16C36_V58_PR791/EDC16C36_V58_PR792/EDC16C36_V58_PR793
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58