display RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Workshop Manual

13B-230
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR364
PR405
PR406
PR365CYLINDER NO. 1 FUEL FLOW CORRECTION
CYLINDER NO. 2 FUEL FLOW CORRECTION
CYLINDER NO. 3 FUEL FLOW CORRECTION
CYLINDER NO. 4 FUEL FLOW CORRECTION
PARAMETER
DEFINITIONThis parameter indicates the cylinder fuel flow correction.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
If the value of these parameters is not equal to 1 (tolerance - 0.7 /+ 0.9) when the engine is running, apply test
7 Incorrect injection quantity.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR364/SID304_V45_PR364/SID301_V48_PR364/SID304_V49_PR364/SID304_V4D_PR364/SID301_V4C_PR364
SID301_V44_PR405/SID304_V45_PR405/SID301_V48_PR405/SID304_V49_PR405/SID304_V4D_PR405/SID301_V4C_PR405
SID301_V44_PR406/SID304_V45_PR406/SID301_V48_PR406/SID304_V49_PR406/SID304_V4D_PR406/SID301_V4C_PR406
SID301_V44_PR365/SID304_V45_PR365/SID301_V48_PR365/SID304_V49_PR365/SID304_V4D_PR365/SID301_V4C_PR365

13B-231
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR381
PARTICLE FILTER DOWNSTREAM TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the particle filter downstream temperature in °C.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
The particle filter downstream temperature sensor only measures temperatures above 50°C.
The measurement ranges are between 150°C and 1000°C.
Measure the resistance of the particle filter downstream temperature sensor, component code 1288, between
connections 3TG and 3XU.
If the resistance of the particle filter downstream temperature sensor is not:
6886Ω 2565Ω 1192Ω replace the particle filter downstream temperature sensor (see MR 385, 364, 370
and 417 Mechanical, 19B,
Exhaust, Particle filter temperature sensors: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR381/SID304_V45_PR381/SID304_V49_PR381/SID301_V4C_PR381

13B-232
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR382
PARTICLE FILTER UPSTREAM TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the particle filter upstream temperature in °C.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
The particle filter upstream temperature sensor only measures temperatures above 50°C.
The measurement ranges are between 150°C and 1000°C.
Measure the resistance of the particle filter upstream temperature sensor, component code 1287, between
connections 3TD and3XT.
If the resistance of the particle filter upstream temperature sensor is not:
6886Ω 2565Ω 1192Ω replace the particle filter downstream temperature sensor (see MR 385, 364, 370
and 417 Mechanical, 19B,
Exhaust, Particle filter temperature sensors: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR382/SID304_V45_PR382/SID304_V49_PR382/SID301_V4C_PR382

13B-233
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR383
WEIGHT OF SOOT IN PARTICLE FILTER
PARAMETER
DEFINITIONThis parameter indicates the weight of soot in the particle filter in grams.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
The weight of the soot contained in the filter must not be greater than 31 g.
If the particle filter warning light is illuminated or if the message Regenerate catalytic converter is displayed,
carry out a special type of driving (see Technical Note 6507, Particle filter fault finding).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR383/SID304_V45_PR383/SID304_V49_PR383/SID301_V4C_PR383

13B-234
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR391
MILEAGE SINCE PARTICLE FILTER REPLACEMENT
PARAMETER
DEFINITIONThis parameter indicates the number of miles (km) since replacement of the particle
filter.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
This parameter determines the distance since the particle filter was last changed.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR391/SID304_V45_PR391/SID304_V49_PR391/SID301_V4C_PR391

13B-235
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR400
NEW EGR VALVE OFFSET
PARAMETER
DEFINITIONThis parameter indicates the new EGR valve offset.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Approximately 850 mV
In the event of a fault, run commands RZ019 and RZ002 Reinitialise programming and EGR Adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR400/SID304_V45_PR400/SID301_V48_PR400/SID304_V49_PR400/SID304_V4D_PR400/SID301_V4C_PR400

13B-236
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR412
DISTANCE VALUE AT LAST SUCCESSFUL REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the last successful regeneration in miles (km).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Mileage counter since last dynamic regeneration (when driving).
After all procedures have been carried out on the particle filter, use RZ030 Particle filter adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR412/SID304_V45_PR412/SID304_V49_PR412/SID301_V4C_PR412

13B-237
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR414
PARTICLE FILTER PRESSURE SENSOR
PARAMETER
DEFINITIONThis parameter indicates the particle filter differential pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
The differential pressure monitors the status of the particle weight in the filter.
The differential pressure of the particle filter is given in mbar.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR414/SID304_V45_PR414/SID304_V49_PR414/SID301_V4C_PR414

13B-238
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR415
TIME SINCE LAST REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the time since the last regeneration in days.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Time counter since last active regeneration (when driving) in days.
After all procedures have been carried out on the particle filter, use RZ030 Particle filter adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR415/SID304_V45_PR415/SID304_V49_PR415/SID301_V4C_PR415

13B-239
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR513
LEVEL 1 WARNING LIGHT DISTANCE COUNTER
PARAMETER
DEFINITIONThis parameter indicates the number of miles (km) travelled since the Level 1 warning
light was last activated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
PR513 = X km
Check the consistency of this parameter with the first appearance of possible faults associated with the Level 1
warning light.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR513/SID304_V45_PR513/SID301_V48_PR513/SID304_V49_PR513/SID304_V4D_PR513/SID301_V4C_PR513