ESP RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Repair Manual

13B-164
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 1
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when driving with the cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is
pressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If status ET415 becomes STATUS 2 with no application of the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact no. 1 and no. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and the clutch pedal is
pressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If status ET415 becomes STATUS 3 without the clutch pedal being pressed, consult the
interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation to
the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-169
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET613
FUEL PRESSURE REGULATOR
STATUS DEFINITIONINACTIVE: This status indicates that the fuel pressure regulator is not active.
ACTIVE: This status indicates that the fuel pressure regulator is active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Note:
This solenoid valve regulates the output pressure of the high pressure pump.
Conformity check with engine stopped and ignition on
INACTIVE
Conformity check with engine running, engine coolant temperature > 80 °C
– Engine stopped.
ACTIVEIf the status is ACTIVE, consult the interpretation of fault DF773 Pressure regulator
circuit.
INACTIVE– Engine stopped.
– Engine under load.
ACTIVEThe status is ACTIVE under low engine loads or when the engine is running at idle
speed.
If the status is INACTIVE with the engine at idle speed, consult the interpretation of fault
DF773 Pressure regulator circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET613/SID304_V45_ET613/SID301_V48_ET613/SID304_V49_ET613/SID304_V4D_ET613/SID301_V4C_ET613

13B-170
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET638
FUEL FLOW REGULATOR
STATUS DEFINITIONINACTIVE: This status indicates that the fuel pressure regulator is INACTIVE.
ACTIVE: This status indicates that the fuel pressure regulator is ACTIVE.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
This solenoid valve regulates the flow of fuel entering the high pressure pump and enables an optimum quantity
of fuel to be pressurised according to operating phase; this improves the output of the Common Rail pump and
thereby the output of the engine as well.
Conformity check with engine stopped and ignition on
ACTIVE
Conformity check with engine running, engine coolant temperature > 80 °C
If the status is ACTIVE, consult the interpretation of fault DF770 Flow regulator
circuit.
INACTIVE– Engine stopped.
– Engine running at idle speed.
ACTIVEThe status is ACTIVE when there is a high engine load.
If the status is INACTIVE with the engine at idle speed, consult the interpretation of fault
DF770 Flow regulator circuit.
INACTIVE– Engine running at idle speed.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET638/SID304_V45_ET638/SID301_V48_ET638/SID304_V49_ET638/SID304_V4D_ET638/SID301_V4C_ET638

13B-171
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET648
FAN UNIT
STATUS DEFINITIONINACTIVE: This status indicates that the cooling fan assembly is INACTIVE.
LOW SPEED: This status indicates that the cooling fan assembly is at LOW SPEED.
HIGH SPEED: This status indicates that the cooling fan assembly is at HIGH SPEED.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVE
The fan assembly is inactive when the coolant temperature does not exceed 96°C.
LOW SPEEDThe injection computer requests the activation of the low speed GMV when:
– the engine coolant temperature is above 96°C,
– the injection computer has system faults that could lead to the engine
overheating,
– the air conditioning is switched on by the driver.
When the high speed fan is supplied:
–status ET022 Low speed fan request becomes activated.
The low-speed fan assembly stops when:
– the engine coolant temperature is below 94°C,
– no fault which could cause engine overheating is present in the injection
system.
– the air conditioning is not switched on by the driver.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET648/SID304_V45_ET648/SID301_V48_ET648/SID304_V49_ET648/SID304_V4D_ET648/SID301_V4C_ET648

13B-173
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET649
WATER IN DIESEL FUEL DETECTOR
STATUS DEFINITIONWITH: This status indicates that the water in diesel fuel detector has detected water in
the diesel fuel.
WITHOUT: This status indicates that the water in diesel fuel detector has not detected
water in the diesel fuel.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
WITH
In the event of a fault, consult the interpretation of fault DF886 Water present in diesel
fuel.
WITHOUTThe status is WITHOUT if no water is detected.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET649/SID304_V45_ET649/SID301_V48_ET649/SID304_V49_ET649/SID304_V4D_ET649/SID301_V4C_ET649

13B-176
MR-372-J84-13B050$624.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
*elec: electric
**circ: circuitET701
PARTICLE FILTER PRESSURE SENSOR
STATUS DEFINITIONACTIVE: This status indicates that the particle filter electric fuel pump is active.
INACTIVE: This status indicates that the particle filter electric fuel pump is not active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Only for vehicles equipped with a particle filter.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVE
INACTIVE
The status is ACTIVE during the particle filter regeneration phase.
If there is a fault, consult the interpretation of fault DF1004 Electric fuel pump control
relay circ**.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID304_V4D_ET701/SID304_V45_ET701/SID304_V49_ET701/SID301_V44_ET701/SID301_V4C_ET701
Siemens Injection
SID304
Vdiag No.: 44-45-49-4D-4C
Program No.: B2

13B-177
MR-372-J84-13B050$624.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET703
CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS DEFINITIONINACTIVE: This status indicates that no button has been pressed.
INCREASE: This status indicates that the increase button is pressed.
DECREASE: This status indicates that the decrease button is pressed.
SUSPEND: This status indicates that the 0 button is pressed.
RESUME: This status indicates that the R button is pressed.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Use the Wiring Diagram Technical Note for Mégane II ph2, Scénic II ph2, CLIO III,
MODUS and Kangoo II.
INACTIVE
Status ET703 becomes INACTIVE when the cruise control/speed limiter button is not
pressed. These buttons are located on the steering wheel.
Refer to the airbag technical note for the vehicle for details on removal of the driver's
airbag and carrying out the checks in complete safety (see 88C, Airbag and
pretensioners).
If status ET703 does not display INACTIVE,
●check the condition of the cruise control/speed limiter +/- button and the
condition of its connector.
●check the condition of the cruise control/speed limiter "R/0" button and the
condition of its connector,
If the connectors are faulty and if there is a repair procedure (see Te c h n i c a l N o t e
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the
connector(s), otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET703/SID304_V45_ET703/SID301_V48_ET703/SID304_V49_ET703/SID304_V4D_ET703/SID301_V4C_ET703
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2

13B-181
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
BRAKE SWITCH NO. 1
BRAKE SWITCH NO. 2
STATUS DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE This status indicates that the brake pedal is released.
NOTESSpecial note:
Only perform these tests if the status does not correspond with the system
programming functions.
Use the Wiring Diagram Technical Note for Mégane II ph2, Scénic II ph2, CLIO III,
MODUS and Kangoo II.
Note:
Statuses ET704 and ET705 should change status at the same time. If they do not, consult the interpretation of
faults DF008 Pedal potentiometer circuit gang 1 and DF009 Pedal potentiometer circuit gang 2.
ACTIVE
If the brake lights are working:
– check the continuity and make sure there is no interference resistance on the
following connection:
Connection code 5A between components 160 and 120, 645 and 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
Continuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
or
INACTIVE
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET704/SID304_V45_ET704/SID301_V48_ET704/SID304_V49_ET704/SID304_V4D_ET704/SID301_V4C_ET704
SID301_V44_ET705/SID304_V45_ET705/SID301_V48_ET705/SID304_V49_ET705/SID304_V4D_ET705/SID301_V4C_ET705

13B-183
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET706
ET707
ET708
ET709
ET710
ET711
ET712
ET713
ET714
ET715STORED ENGINE STATUS NO. 1
STORED ENGINE STATUS NO. 2
STORED ENGINE STATUS NO. 3
STORED ENGINE STATUS NO. 4
STORED ENGINE STATUS NO. 5
STORED ENGINE STATUS NO. 6
STORED ENGINE STATUS NO. 7
STORED ENGINE STATUS NO. 8
STORED ENGINE STATUS NO. 9
STORED ENGINE STATUS NO. 10
STATUS DEFINITIONRUNNING: This status indicates that the stored engine status is engine running.
STOPPED: This status indicates that the stored engine status is engine stopped.
NOTESSpecial note:
Check the interpretation of these parameters only on ALP21 Particle filter warning
light illuminated.
Vdiag 4D and 49 only.
Each STATUS between ET706 and ET715 corresponds to regeneration failures for which the mileage is recorded
by the parameters PR794 Regeneration failure record No. 1 to PR803 Regeneration failure record No. 10
(for example: PR797 Regeneration failure record No. 4 is linked to ET709 Stored engine status no. 4).
"RUNNING"
The status is ACTIVE as soon as the ignition is switched on.
"STOPPED"If the status is STOPPED, regeneration failure due to the engine being switched off.
+ APCDo not interpret this engine status.
"NONE"Do not interpret this engine status.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID304_V4D_ET706/SID304_V4D_ET707/SID304_V4D_ET708/SID304_V4D_ET709/SID304_V4D_ET710/SID304_V4D_ET711/
SID304_V4D_ET712/SID304_V4D_ET713/SID304_V4D_ET714/SID304_V4D_ET715/SID304_V49_ET706/SID304_V49_ET707/
SID304_V49_ET708/SID304_V49_ET709/SID304_V49_ET710/SID304_V49_ET711/SID304_V49_ET712/SID304_V49_ET713/
SID304_V49_ET714/SID304_V49_ET715/SID301_V4C_ET707/SID301_V4C_ET708/SID301_V4C_ET709/SID301_V4C_ET710/
SID301_V4C_ET711/SID301_V4C_ET712/SID301_V4C_ET713/SID301_V4C_ET714/SID301_V4C_ET715

13B-184
MR-372-J84-13B050$624.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET741
OPTIONAL VEHICLE SPEED RESTRICTION
STATUS DEFINITIONACTIVE: This status indicates that the speed restriction is activated.
INACTIVE: This status indicates that the speed restriction is deactivated.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
This status indicates whether the vehicle speed restriction is a customer option, using
the command SC040 Speed limiter.
Kangoo II only.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVE
INACTIVE
Vehicle speed restricted using command SC040 Speed limiter.
See the interpretation of parameter PR879 Maximum speed authorized to find the
configured speed restriction.
Optional speed restriction function deactivated.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V48_ET741/SID304_V4D_ET741/SID301_V4C_ET741
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2