ESP RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Owners Manual

13B-223
MR-372-J84-13B050$741.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR130
CRUISE CONTROL SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the cruise control speed setpoint in mph (km/h).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults must be present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
Indicates the cruise control cruising speed.
Cruise control can only be activated for a speed.
V > 18 mph (30 km/h)
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR130 / SID304_V45_PR130 / SID301_V48_PR130 / SID304_V49_PR130 / SID304_V4D_PR130 / SID301_V4C_PR130

13B-224
MR-372-J84-13B050$741.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR132
AIR FLOW
PARAMETER
DEFINITIONThis parameter indicates the inlet air flow in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults must be present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
Diagrams Technical Notes.
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold, run test 10 Air line at the turbocharger):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, use ALP2 The engine does not start or starts with difficulty,
– oil vapour recirculation circuit connected correctly,
–absence of leaks or blockages in the low and high pressure air circuits: ducts, presence and tightness
of the mounting clips, mounting of the turbocharging pressure sensor, exchanger, etc.
– check that the damper valve is not jammed shut (except Vdiag 4C).
Carry out the necessary repairs.
Check the electrical conformity of the air flow sensor:
Check the + 5 V supply to the air flowmeter.
– connection 3KJ of component 799.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR132 / SID304_V45_PR132 / SID301_V48_PR132 / SID304_V49_PR132 / SID304_V4D_PR132 / SID301_V4C_PR132

13B-226
MR-372-J84-13B050$741.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR171
AIR FLOW SETPOINT FOR EGR
PARAMETER
DEFINITIONThis parameter indicates the flow of air required by the EGR valve in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Indicates the air flow required by the EGR valve
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR171 / SID304_V45_PR171 / SID301_V48_PR171 / SID304_V49_PR171 / SID304_V4D_PR171 / SID301_V4C_PR171

13B-227
MR-372-J84-13B050$741.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR190
IDLE SPEED SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the engine's rotational speed in rpm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
With the ignition on, the value is 0 rpm.
In the event of a fault, consult the interpretation of faults DF195 Engine speed / camshaft sensor consistency,
DF097 Camshaft sensor circuit and DF005 Engine speed sensor circuit.
Conformity check with engine running, engine coolant temperature > 80°C
With the engine idling, the value is approximately 800 rpm.
In the event of a fault, consult the interpretation of faults DF195 Engine speed / camshaft sensor consistency,
DF097 Camshaft sensor circuit and DF005 Engine speed sensor circuit.
The difference between the engine idle speed and its setpoint must be less than 50 rpm.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR190 / SID304_V45_PR190 / SID301_V48_PR190 / SID340_V49_PR190 / SID304_V4D_PR190 / SID301_V4C_PR190

13B-228
MR-372-J84-13B050$741.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of parameters
PR224
TURBOCHARGING PRESSURE SENSOR VOLTAGE
STATUS DEFINITIONThis parameter indicates the turbocharging pressure sensor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
0 V < PR224 < 5 V
In the event of a fault, refer to the interpretation of fault DF012 Sensor supply voltage no. 2.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V48_PR224 / SID301_V44_PR224 / SID301_V4C_PR224Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4C
Program No.: B1 and B2

13B-229
MR-372-J84-13B050$780.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of parameters
PR228
INJECTION CONTROL CAPACITOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the injector control capacitor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
49 V < PR228 < 96 V
In the event of a fault, refer to the interpretation of faults DF026, DF027, DF028, DF029 Cylinder 1, 2, 3, 4
injector control circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR228/SID304_V45_PR228/SID301_V48_PR228/SID304_V49_PR228/SID304_V4D_PR228/SID301_V4C_PR228
MR-372-J84-13B050$780.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2

13B-235
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR400
NEW EGR VALVE OFFSET
PARAMETER
DEFINITIONThis parameter indicates the new EGR valve offset.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Approximately 850 mV
In the event of a fault, run commands RZ019 and RZ002 Reinitialise programming and EGR Adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR400/SID304_V45_PR400/SID301_V48_PR400/SID304_V49_PR400/SID304_V4D_PR400/SID301_V4C_PR400

13B-236
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR412
DISTANCE VALUE AT LAST SUCCESSFUL REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the last successful regeneration in miles (km).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Mileage counter since last dynamic regeneration (when driving).
After all procedures have been carried out on the particle filter, use RZ030 Particle filter adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR412/SID304_V45_PR412/SID304_V49_PR412/SID301_V4C_PR412

13B-237
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR414
PARTICLE FILTER PRESSURE SENSOR
PARAMETER
DEFINITIONThis parameter indicates the particle filter differential pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
The differential pressure monitors the status of the particle weight in the filter.
The differential pressure of the particle filter is given in mbar.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR414/SID304_V45_PR414/SID304_V49_PR414/SID301_V4C_PR414

13B-238
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR415
TIME SINCE LAST REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the time since the last regeneration in days.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Time counter since last active regeneration (when driving) in days.
After all procedures have been carried out on the particle filter, use RZ030 Particle filter adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR415/SID304_V45_PR415/SID304_V49_PR415/SID301_V4C_PR415