Mr 392 RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Repair Manual

13B-120
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF1008
PRESENT
OR
STOREDTURBINE UPSTREAM TEMPERATURE REGULATION
1. DEF: Parameter at maximum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present after a road test with particle filter regeneration.
Special notes:
If the fault is present:
The level 1 fault warning light is lit on the instrument panel.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Check the condition of the air circuit upstream of the turbine.
Check that circuit is not leaking and does not have cracks.
Check the connection and condition of the connector of the turbine upstream temperature sensor, component
code 1589.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the turbine upstream temperature sensor, component code 1589 between
connections 3B
and 3JQ.
If the resistance is not:
5910Ω < X < 5930Ω at 300°C,
1760Ω < X < 1780Ω at 400°C,
714Ω < X < 734Ω at 500°C,353Ω < X < 373Ω at 600°C,
177Ω < X < 227Ω at 700°C,
106Ω < X < 156Ω at 800°C,
replace the turbine upstream temperature sensor.
With the ignition on, check the continuity, insulation and absence of interference resistance on the following
connections:
–3JQ between components 1589 and 120,
–3B between components 1589 and 120.
If the connection(s) are faulty and there is a repair method (see
Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the turbine upstream temperature sensor.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF1008 / SID304_V45_DF1008 / SID301_V48_DF1008 / SID304_V49_DF1008 / SID304_V4D_DF1008 / SID301_V4C_DF1008

13B-121
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF1009
PRESENT
OR
STOREDCATALYTIC CONVERTER 1 DOWNSTREAM TEMPERATURE
REGULATION
1. DEF: Signal outside lower limit
2. DEF: Signal outside upper limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present after a road test with particle filter regeneration.
Special notes:
If the fault is present:
The level 1 fault warning light is lit on the instrument panel.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Check the connection and condition of the connector of the catalytic converter 1 downstream temperature
sensor, component code 1765.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
With the ignition on, check the continuity, insulation and absence of interference resistance on the following
connections:
–3AGX between components 1765 and 120,
–3AGY between components 1765 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the turbine upstream temperature sensor.
While the engine is idling, check the return flow rate at the injectors.
After 5minutes the return volume must be between 16 mland 24 ml per injector.
If this tolerance is incorrect, replace the faulty injector(s).
Check the temperature of the catalytic converter; check that it is not too low.
Check that the exhaust system is not pierced.
Replace any faulty components.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF1009 / SID304_V45_DF1009 / SID301_V48_DF1009 / SID304_V49_DF1009 / SID304_V4D_DF1009 / SID301_V4C_DF1009

13B-123
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF1070
PRESENT
OR
STOREDCOLD LOOP
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present with the engine running and an air conditioning request.
Order of priority in the event of more than one fault:
Deal with fault DF049 Refrigerant sensor circuit first if it is present or stored.
Use the CLIO III, MODUS, MEGANE II ph2 and SCENIC II ph2 Wiring Diagrams
Technical Note.
When the fault is present or stored, the heating and air conditioning system is inhibited. There is no longer any air
conditioning.
Check the air conditioning fuse and check the air conditioning compressor connector, component code 171.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
– 38R between components 171 and 1337,
– Mbetween the earth and component 171.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Manually check if the compressor is jammed (turn the clutch plate manually to check that there is no point of
resistance).
In the event of jamming, replace the air conditioning compressor (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), Mechanical, 62A, Air conditioning, Compressor:
Removal - Refitting)
Charge the air conditioning circuit, check for any leaks and repair if necessary (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), Mechanical, 62A, Air conditioning, Air conditioning: Check
and air conditioning:
Draining - Filling).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF1070 / SID304_V45_DF1070 / SID301_V48_DF1070 / SID304_V49_DF1070 / SID304_V4D_DF1070 / SID301_V4C_DF1070

13B-162
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET405
CLUTCH PEDAL SWITCH
STATUS DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
"INACTIVE"
Check the condition and the fitting of the clutch pedal switch (see MR 392, 385, 364,
370 and 417 Mechanical, 37A, Mechanical component controls, Clutch pedal
position sensor: Removal - Refitting).
Remove the clutch pedal switch and check the insulation between connections MAM
and 86D (for Mégane II ph 2, Scénic II ph2 and Kangoo II) and between connections
MAS and 86D (for Clio III and Modus) of component675 with the switch in the rest
position.
– Repeat this operation with the switch engaged, and check the continuity between
the two connections.
If these two checks are not correct, replace the clutch pedal switch (see MR 392, 385,
364, 370 and 417 Mechanical, 37A, Mechanical component controls, Clutch pedal
position sensor: Removal - Refitting).
Then check the continuity and absence of interference resistance of the following
connection:
– connection code 86D between components 120 and 675.
– Check that the earth is correct on connectionMAM (for Mégane II ph 2, Scénic II
ph2 and Kangoo II) or on connectionMAS (for Clio III and Modus) of
component675.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
"ACTIVE"Check the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch and check the insulation between connections MAM
and 86D (for Mégane II ph 2, Scénic II ph2 and Kangoo II) and between connections
MAS and 86D (for Clio III and Modus) of component675 with the switch in the rest
position.
– Repeat this operation with the switch engaged, and check the continuity between
the two connections.
If these two checks are not correct, replace the clutch pedal switch (see MR 392, 385,
364, 370 and 417 Mechanical, 37A, Mechanical component controls, Clutch pedal
position sensor: Removal - Refitting).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET405/SID304_V45_ET405/SID301_V48_ET405/SID304_V49_ET405/SID304_V4D_ET405/SID301_V4C_ET405

13B-174
MR-372-J84-13B050$624.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET673
JAMMED ACCELERATOR PEDAL
STATUS DEFINITIONYES: This status indicates that the accelerator pedal is detected to be jammed.
NO: This status indicates that the accelerator pedal is not detected to be jammed.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
NOTESSpecial notes:
Apply this procedure only if the status is YES.
Use the Wiring Diagram Technical Note for Mégane II ph2, Scénic II ph2, CLIO III,
MODUS and Kangoo II.
Check the condition of the connector for the brake switch, component code160.
Check the condition of the connector for the accelerator potentiometer, component code921.
Check the condition of the connector for the engine management computer, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Measure the resistance of the pedal potentiometer gang 1 between connections 3LR and 3LT.
If the resistance of the pedal potentiometer is not between 0.8 kΩ and
2.6 kΩ, replace the pedal potentiometer
(see MR 392, 385, 364, 370 and 417 Mechanical, 13B, Diesel injection, Accelerator pedal potentiometer:
Removal - Refitting).
Measure the resistance of the pedal potentiometer on gang 2 between connections 3LU and 3LV.
If the resistance of the pedal potentiometer is not between 0.8 kΩ and
4.9 kΩ, replace the pedal potentiometer
(see MR 392, 385, 364, 370 and 417 Mechanical, 13B, Diesel injection, Accelerator pedal potentiometer:
Removal - Refitting).
YES or NOThis status varies when the ignition is on or the engine is running depending on the
status of the accelerator pedal.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET673/SID301_V48_ET673/SID301_V4C_ET673
Siemens Injection
SID304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2

13B-178
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 1
INCREASE
Status ET703 becomes INCREASE when the cruise control/speed limiter + button is
pressed. This button is on the steering wheel, on the left-hand side.
Refer to the airbag technical note for the vehicle for details on removal of the driver's
airbag and carrying out the checks in complete safety (see 88C, Airbag and
pretensioners).
If status ET703 does not display INCREASE, check the status of the cruise control/
speed limiter +/- button, and the condition of its connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, wiring: Precautions for repair), repair the connector(s);
otherwise replace the wiring.
Measure the resistance on the following connections while pressing the + button
(on the button tracks):
●Connection code86G of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 300Ω, check the continuity of the connection for
the button when the button is in the rest position.
If there is continuity, replace the +/- control button (see MR 392, 385, 364, 370 and 417
Mechanical, 83D, Cruise control, Switch on the steering wheel: Removal -
Refitting).
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-182
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
CONTINUED
INACTIVE
CONTINUED
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the values obtained are not correct, replace the brake switch (see MR 392, 385, 364,
370 and 417 Mechanical, 37A, Mechanical component controls, Brake light
switch: Removal - Refitting).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-197
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR030
CONTINUED
Pedal sensor connected, vehicle ignition on and engine stopped:
– check that the value of PR030 Accelerator pedal position:
0% no load,
100% full load,
138% full load after pedal kickdown point.
– If the value is not correct, replace the accelerator pedal sensor (see MR 392, 385, 364, 370
and 417
Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.

13B-200
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR038
RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the fuel pressure in the rail in bars.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after an inconsistency appears on the Parameter screen,
– following the activation of command AC003 Fuel pressure solenoid valve,
– following a customer complaint (starting problems, poor performance, stalling, etc.).
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
Diagrams Technical Notes.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3LX between components 1032 and 120,
–3LY between components 1032 and 120,
–3LZ between components 1032 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If all these connections are correct, check for the fuel pressure sensor supply:
+ 5 V on connection code 3LX between components 1032 and 120,
Earth on connection code 3LZ between components 1032 and 120.
If the connection(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the low and high pressure diesel circuit sealing (visual checks, odours): on pump body, pressure release
valve, pipes, rail and injector unions, injector wells, etc.
If all the above checks are correct:
With the vehicle ignition on, and engine stopped for over 1 minute:
Display PR038; if the value is lower than 30 bar, the sensor is correct.
Otherwise replace the rail pressure sensor (see MR 392, 385, 364, 370
and 417 Mechanical, 13B, Diesel
injection, Rail pressure sensor: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR038/SID304_V45_PR038/SID301_V48_PR038/SID304_V49_PR038/SID304_V4D_PR038/SID301_V4C_PR038

13B-205
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR059
INLET AIR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the air inlet temperature in °C.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Check the condition of the air flowmeter connections, component code 799.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3ABQ and 3DW of component 799.
If the resistance is not:
(theoretical values)
3553 Ω < X < 3875 Ω at 10°C,
2353 Ω < R < 2543 Ω at 20°C,
1613 Ω < R < 1729 Ω at 30°C,
replace the air flowmeter (see MR 392, 385, 364, 370 and 417, Mechanical, 12A, Fuel mixture, Air flowmeter:
Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR059/SID304_V45_PR059/SID301_V48_PR059/SID304_V49_PR059/SID304_V4D_PR059/SID301_V4C_PR059