pressure RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Repair Manual

13B-224
MR-372-J84-13B050$741.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR132
AIR FLOW
PARAMETER
DEFINITIONThis parameter indicates the inlet air flow in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults must be present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
Diagrams Technical Notes.
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold, run test 10 Air line at the turbocharger):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, use ALP2 The engine does not start or starts with difficulty,
– oil vapour recirculation circuit connected correctly,
–absence of leaks or blockages in the low and high pressure air circuits: ducts, presence and tightness
of the mounting clips, mounting of the turbocharging pressure sensor, exchanger, etc.
– check that the damper valve is not jammed shut (except Vdiag 4C).
Carry out the necessary repairs.
Check the electrical conformity of the air flow sensor:
Check the + 5 V supply to the air flowmeter.
– connection 3KJ of component 799.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR132 / SID304_V45_PR132 / SID301_V48_PR132 / SID304_V49_PR132 / SID304_V4D_PR132 / SID301_V4C_PR132

13B-228
MR-372-J84-13B050$741.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of parameters
PR224
TURBOCHARGING PRESSURE SENSOR VOLTAGE
STATUS DEFINITIONThis parameter indicates the turbocharging pressure sensor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
0 V < PR224 < 5 V
In the event of a fault, refer to the interpretation of fault DF012 Sensor supply voltage no. 2.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V48_PR224 / SID301_V44_PR224 / SID301_V4C_PR224Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4C
Program No.: B1 and B2

13B-237
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR414
PARTICLE FILTER PRESSURE SENSOR
PARAMETER
DEFINITIONThis parameter indicates the particle filter differential pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
The differential pressure monitors the status of the particle weight in the filter.
The differential pressure of the particle filter is given in mbar.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR414/SID304_V45_PR414/SID304_V49_PR414/SID301_V4C_PR414

13B-244
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*sens: sensor
*Circ: circuit
*diff: differential
*Press: PressurePR669
PARTICLE FILTER DIFF* PRESS* SENS* VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the particle filter differential pressure sensor in
volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
PR669 ≈5V
In the event of a fault, consult the interpretation of DF1003 Particle filter differential pressure sensor circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR669/SID304_V45_PR669/SID304_V49_PR669/SID301_V4C_PR669

13B-258
MR-372-J84-13B050$819.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of commands
SPECIAL COMMAND
SC001: Enter saved data.
SC003: Save computer data.
SC013: Enter VIN.
SC017: Particle filter regeneration (Only for vehicles equipped with a particle filter).
SC040: Speed limiter (Kangoo II only).
SC041: Modification of the commercial vehicle idle speed (Kangoo II only).
CLEARING
RZ001: Fault memory.
Enables the faults to be cleared from the computer memory.
RZ002: EGR adaptives.
Use this command at the time of replacement or when cleaning the EGR valve.
RZ004: Pressure regulation adaptives.
This mode initialises the variables related to the regulation function.
RZ005: Programming (except Kangoo II).
This command enables you to reinitialise all the computer data (engine adaptives, EGR, rail, etc.).
RZ019: Reinitialise programming.
This mode initialises all of the programming contained in EEPROM.
RZ030: Particle filter adaptives (Vdiag 45, 49 and 4D only).
This mode initialises the variables related to the particle filter function.
ACTUATION
AC003: Fuel pressure solenoid valve.
AC005 to AC008: Injectors for cylinders 1 to 4.
Running this lets you listen to the operation of the injector on the cylinder in question.
AC012: Damper valve (except Vdiag 4C).
Activating this lets you listen to the operation of the damper valve.
AC029: High-pressure circuit seal check.
Running this lets you check the high pressure circuit sealing after an operation has been carried out.
Run this command with the engine running and the engine coolant temperature above 60°C.
MR-372-J84-13B050$819.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4CProgram No.: B1 and B2

13B-262
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC017
PARTICLE FILTER REGENERATION
NOTESCarry out this command only under the following conditions:
– DF308 Clogged particle filter present.
Ignition on and engine stopped.
Vdiag 45, 49 and 4D only.
WARNING:
–It is essential to carry out the next procedure in accordance with the safety and cleanliness guidelines,
(see MR 364 (Mégane II), 370 (Scénic II), 417 (Kangoo II), 385 (Modus), 392 (Clio III), Mechanical, 19B,
Exhaust, Particle filter: Cleaning).
– do not run command AC029 High pressure circuit seal test until regeneration has finished.
– before each regeneration, check the fuel level,
– before and after each regeneration, check the oil level.
With the engine running and the vehicle stopped, this function allows the particle filter to be regenerated.
Safety instructions to be followed:
The regeneration causes exhaust fumes and high temperatures.
The vehicle must be outside during regeneration.
If it is not possible to carry out regeneration outside, check that the extractor fan can withstand the very high
regeneration temperatures.
Perform regeneration on a surface free from fire risks (oil, dry leaves, etc.).
Nothing should be left in the vicinity of the exhaust pipe.
Before regeneration:
– Respect After-Sales recommendations for particle filter regeneration.
– Check the oil level to prevent the engine from racing.
– Check the fuel level.
– Check the sealing on the 5th particle filter injector circuit using actuator AC237 Fuel pump relay.
– Check that there are no leaks or blockages in the exhaust pipe,
To perform regeneration:
– Vehicle stopped and in neutral.
– Engine running and warm.
– No pedal depressed (accelerator and clutch).
– No faults present preventing regeneration from being carried out on the system.
– No leak in the 5th particle filter injector circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V45_SC017 / SID304_V49_SC017 / SID304_V4D_SC017 / SID301_V4C_SC017

13B-263
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC017
CONTINUED
After-Sales regeneration comprises 4 important stages:
– Heating of the engine and checking for a small quantity of soot in the particle filter by measuring the differential
pressure.
– The system changes from combustion mode and starts to regenerate the particle filter. Gradual cooling of the
particle filter.
– End of After-Sales regeneration.
Stopping conditions:
– Dialogue with the diagnostic tool has been lost.
– Vehicle movement detected by speed sensor.
– Brake or clutch pedal depressed.
– Stop regeneration requested by the diagnostic tool.
– End of test.
The procedure lasts 30 minutes.
– At the end of regeneration, a message announces whether the regeneration has been successful or which
operations to carry out.
CONFIRMING THE REGENERATION PROCESS:
At the end of regeneration, a message appears to announce whether the regeneration was successful:
particle filter regeneration successful: regeneration completed correctly.
weight of soot too high - run command SC017 again: regeneration failed because the weight of soot at
the end of regeneration was too high and the temperature upstream of the particle filter was too low. Check
the oil level before starting another regeneration.
weight of soot too high: regeneration failed because the weight of soot at the end of regeneration was
too high in spite of the correct temperature upstream of the particle filter. The particle filter is full of residue
(regeneration impossible), refer to the fault finding chart ALP21 Particle filter warning light lit.
present or stored fault: regeneration failed because faults were declared.
Refer to the interpretation of faults, after resolving the faults, run command SC017 again.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
.

13B-274
MR-372-J84-13B050$897.mif
V17
DIESEL INJECTION
Fault finding – Fault Finding Chart
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ALP 2 The engine does not start or starts with difficulty
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check the presence and conformity of the fuel by running Test 13 Diesel fuel conformity check.
Carry out fault finding on the charge circuit (See Technical Note 6014A, Checking the charging circuit or 87G,
Engine compartment connection unit).
Check the starter and the starter relay (see Technical Note 3632A, Starter fault finding).
Check the injection computer main relay (refer to the interpretation of fault DF015 Main relay control circuit).
Check the injection computer: that the connections and wiring are in good condition, that earths and feeds are
present.
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the camshaft sensor and TDC sensor, as well as their wiring (refer to the interpretation of faults DF005
Engine speed sensor circuit and DF097 Camshaft sensor circuit).
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, if not replace it.
Check the air inlet circuit (refer to the interpretation of fault DF301 Air inlet circuit).
Check that the damper valve operates correctly (refer to the interpretation of fault DF641 Damper valve circuit).
Check the low pressure fuel supply system by performing test 1 Low pressure supply check and test 2
Internal fuel transfer pump (ITP) check.
Check the high pressure fuel supply system by performing test 3 High pressure fuel pressure solenoid valve
check, test 4 High pressure pump (HPP) and fuel flow solenoid valve check and test 5 Rail high pressure
regulation circuit check.
Check the injectors by performing test 6 Major leak in injectors/injectors open and test 7 Incorrect injection
amount.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_ALP2 / SID304_V45_ALP2 / SID301_V48_ALP2 / SID304_V49_ALP2 / SID304_V4D_ALP2 / SID301_V4C_ALP2

13B-275
MR-372-J84-13B050$897.mif
V17
DIESEL INJECTION
Fault finding – Fault Finding Chart
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ALP 3 Starting difficult with cold engine
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check the grade of the engine oil and that the engine oil level is correct.
Perform fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Check the starter (see Technical Note 3632A, Starter fault finding).
Check the coolant temperature sensor, fuel sensor and air inlet sensor (refer to the interpretation of faults DF001
Coolant temperature sensor circuit, DF098 Fuel temperature sensor circuit and DF301 Air inlet circuit).
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the preheating system (refer to the interpretation of fault DF025 Preheating unit diagnostic line).
Check the low pressure fuel supply system by performing test 1 Low pressure supply check and test 2
Internal fuel transfer pump (ITP) check.
Check compression values.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_ALP3 / SID304_V45_ALP3 / SID301_V48_ALP3 / SID304_V49_ALP3 / SID304_V4D_ALP3 / SID301_V4C_ALP3

13B-278
MR-372-J84-13B050$897.mif
V17
DIESEL INJECTION
Fault finding – Fault Finding Chart
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ALP 6 Engine idle speed too low or unstable
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check the presence and conformity of the fuel by running Test 13 Diesel fuel conformity check.
Check the injection computer: that the connections and wiring are in good condition, that earths and feeds are
present.
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the air inlet circuit (refer to the interpretation of fault DF301 Air inlet circuit).
Check that the damper valve operates correctly (refer to the interpretation of fault DF641 Damper valve circuit).
Check the air flowmeter (refer to the interpretation of faults DF039 Inlet air temperature sensor circuit, DF129
Air flow requested and DF056 Air flow sensor circuit).
Check the air conditioning pressure sensor (refer to the interpretation of fault DF049 Refrigerant sensor circuit).
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If fault DF308 Particle filter clogged is present, replace the particle filter.
Run command RZ030 Particle filter adaptives after replacing the particle filter.
Check the low pressure fuel supply system by performing test 1 Low pressure supply check and test 2
Internal fuel transfer pump (ITP) check.
Check the high pressure fuel supply system by performing test 3 High pressure fuel pressure solenoid valve
check, test 4 High pressure pump (HPP) and fuel flow solenoid valve check and test 5 Rail high pressure
regulation circuit check.
Check the injectors by performing test 6 Major injector leak/injectors open and test 7 Incorrect injection
amount.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_ALP6 / SID304_V45_ALP6 / SID301_V48_ALP6 / SID304_V49_ALP6 / SID304_V4D_ALP6 / SID301_V4C_ALP6