ignition RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals User Guide

13B-36
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF016
STOREDEGR VALVE CONTROL CIRCUITCO.0: Open circuit or short circuit to earth.
CC.1: Short circuit to +12 volts.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Special notes:
If fault DF016 is present: the engine is unstable and may even stall.
Starting difficult or even impossible when cold.
See Technical Note Wiring Diagrams of the vehicle concerned.
Check the connection and condition of the exhaust gas recirculation solenoid valve connector, component code
169.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component code
120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for the supply: 13 V < X < 14 V (with the engine running), 11.5 V < X < 12.5 V (with the ignition on and
the engine stopped) on connection 3FB2 of component 169.
Check the insulation and continuity of the following connections:
–3GB between components 169 and 120,
–3FB2 between components 169 and 120.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Measure the resistance of the EGR valve, component code 169:
– with the engine stopped, the EGR valve will be closed (unless there is a fault),
– wait for the ambient temperature around the valve to stabilise (approximately 20°C),
– measure the resistance between connections 3FB2 and 3GB of component 169. The resistance must be
between
7.5 Ω
< R < 8.5 Ω (at 20°C),
– measure the resistance between connections 3GC and 3JM of component 169. The resistance must be between
2.4 KΩ < R < 5.6 KΩ (at 20°C),
– measure the resistance between connections 3JM and 3EL of component 169. The resistance must be between
800 Ω < R < 3.6 KΩ (ατ 20°C),
if the value is not correct, replace the EGR valve (see MR 364 (Mégane II), MR 370
(Scénic II), Mechanical, 14A, Emission control, Exhaust gas recirculation solenoid valve: Removal -
Refitting). If the EGR valve was replaced, use command RZ002 EGR adaptives to reinitialise the EGR valve
offsets.
If the fault is still present, contact the Techline.
DDCR_V44_DF016M/DDCR_V48_DF016M

13B-37
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF017
PRESENTPRE-POSTHEATING UNIT CONTROL CIRCUITCO.0: Open circuit or short circuit to earth.
CC.1: Short circuit to +12 volts.
NOTESSpecial notes: If DF017 is present, starting difficult (or impossible when cold). If
CO.0: the plugs are permanently switched on with risk of damage or even engine
failure.
Check the connection and condition of the preheating unit connector.
Repair if necessary.
Check the connection and condition of the computer's 32-track grey connector C.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
+12 V after ignition feed Track 3 preheating unit
Computer connector C track D3 Track 9 preheating unit
Computer connector C track F2 Track 8 preheating unit
Repair if necessary
DDCR_V44_DF017P/DDCR_V48_DF017P

13B-40
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF026
PRESENT
OR
STOREDCYLINDER 1 INJECTOR CONTROL CIRCUIT
CO: Open circuit.
CC: Short circuit.
1.DEF: At minimum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present with the engine at idle speed.
Special notes: When this fault appears, the idle speed is stuck at 1000 rpm, there is
engine noise, the engine speed is unsteady, the engine performance is reduced, and the
level 1 warning light illuminates along with the message Faulty injection.
CO - CC
NOTESNone.
Switch off the ignition and wait 15 seconds.
Check the connection and condition of the injector connector.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Run command AC005 Cylinder 1 injector.
If a cycle of 5 actuations of injector 1 cannot be heard working, connect the cylinder 2 injector wire to the cylinder
1 injector and run command AC006 Cylinder 2 injector.
Does this injector actuation cycle work?
Note:
If the wires cannot be swapped, continue the procedure by replying YES to the previous question.
DDCR_V44_DF026/DDCR_V48_DF026

13B-42
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF027
PRESENT
OR
STOREDINJECTOR CYLINDER 2 CONTROL CIRCUIT
CO: Open circuit.
CC: Short circuit.
1.DEF: At minimum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present with the engine idling.
Special notes: When this fault appears, the idle speed is stuck at 1000 rpm, there is
engine noise, the engine speed is unsteady, the engine performance is reduced, and the
level 1 warning light illuminates along with the message Faulty injection.
CO - CC
NOTESNone.
Switch off the ignition and wait 15 seconds.
Check the connection and condition of the injector connector. Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B. Repair if necessary.
Run command AC006 Cylinder 2 injector.
If a cycle of 5 actuations of injector 2 cannot be heard working, connect the cylinder 3 injector wire to the cylinder
2 injector and run command AC007 Cylinder 3 injector.
Does this injector actuation cycle work?
Note:
If the wires cannot be swapped, continue the procedure by replying YES to the previous question.
DDCR_V44_DF027/DDCR_V48_DF027

13B-44
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF028
PRESENT
OR
STOREDCYLINDER 3 INJECTOR CONTROL CIRCUIT
CO: Open circuit.
CC: Short circuit.
1.DEF: At minimum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Special notes: When this fault appears, the idle speed is stuck at 1000 rpm, there is
engine noise, the engine speed is unsteady, the engine performance is reduced, and the
level 1 warning light illuminates along with the message Faulty injection.
CO - CC
NOTESNone.
Switch off the ignition and wait 15 seconds.
Check the connection and condition of the injector connector. Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B. Repair if necessary.
Run command AC007 Cylinder 3 injector.
If 5 actuation cycles of injector 3 cannot be heard working, connect the cylinder 4 injector wire to the cylinder 3
injector and use command AC008 Cylinder 4 injector.
Does this injector actuation cycle work?
Note:
If the wires cannot be swapped, continue the procedure by replying YES to the previous question.
DDCR_V44_DF028/DDCR_V48_DF028

13B-46
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF029
PRESENT
OR
STOREDCYLINDER 4 INJECTOR CONTROL CIRCUIT
CO: Open circuit.
CC: Short circuit.
1.DEF: At minimum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present with the engine idling.
Special notes: When this fault appears, the idle speed is stuck at 1000 rpm, there is
engine noise, the engine speed is unsteady, the engine performance is reduced, and the
level 1 warning light illuminates along with the message Faulty injection.
CO - CC
NOTESNone.
Switch off the ignition and wait 15 seconds.
Check the connection and condition of the injector connector. Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B. Repair if necessary.
Run command AC008 Cylinder 4 injector.
If 5 actuation cycles of injector 4 cannot be heard working, connect the cylinder 3 injector wire to the cylinder 4
injector and use command AC007 Cylinder 3 injector.
Does this injector actuation cycle work?
Note:
If the wires cannot be swapped, continue the procedure by replying YES to the previous question.
DDCR_V44_DF029/DDCR_V48_DF029

13B-50
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF038
CONTINUED
4.DEFNOTESNone.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check that the individual injector correction (C2I) matches the injector. If not, write the C2I (see Configurations
and programming).
If the C2I does match the injectors, contact the Techline.
1.DEF
5.DEF
6.DEF
8.DEF
NOTESNone.
Contact the Techline.
2.DEF
3.DEF
NOTESNone.
Deal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Switch off the ignition and wait 30 seconds.
Switch on the ignition again and run a new check using the diagnostic tool. If the fault is still present, clear the
computer's fault memory for a second time.
If the fault is still present, contact the Techline.

13B-52
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF047
STOREDCOMPUTER SUPPLY VOLTAGE1.DEF: Above maximum threshold.
2.DEF: Below minimum threshold.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine running above 1000 rpm.
Measure the battery voltage when the ignition is switched on.
If the battery voltage < 10 V recharge the battery.
Check the condition and connection of the battery terminals.
Repair if necessary.
Check the vehicle's charging circuit.
Repair if necessary.
Check the connection and condition of the black 32-track computer connector A.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
+ after ignition feed. Track D1 computer connector A
Chassis earth Tracks G4 and H4 computer connector A
Repair if necessary.
DDCR_V44_DF047M/DDCR_V48_DF039P

13B-54
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF050
PRESENT
OR
STOREDBRAKE SWITCH CIRCUIT
1.DEF: No signal.
2.DEF: Inconsistency.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present when the ignition is switched on, when decelerating or when
the brake pedal is depressed.
Deal with the fault even if it is stored.
Check the connection and condition of the switch connector.
Repair if necessary.
Check for the +12 V feed on the switch supply.
Repair if necessary.
Check the connection and condition of the black 32-track connector A and grey 32-track connector C of the
computer.
Repair if necessary.
Check that the switch is working.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Brake light switch track 1 and 3 + after ignition feed.
Brake light switch track 4Track E4 computer connector A
Repair if necessary.
DDCR_V44_DF050/DDCR_V48_DF050

13B-55
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF051
PRESENTCRUISE CONTROL/SPEED LIMITER FUNCTION1.DEF: inconsistency.
2.DEF: On/off switch.
NOTESNone.
Check the connection and condition of the black 32-track computer connector A.
Repair if necessary.
Check the connection and condition of the connections of the on - off control switch of the cruise control - speed
limiter function.
Repair if necessary.
Check for the 12 V after ignition feed on track A2 of the on - off switch of the cruise control - speed limiter
function.
Repair if necessary.
Carry out an operating check on the cruise control/speed limiter function on/off switch (consult the
interpretation of ET042 Cruise control/speed limiter).
If the fault is still present, contact the Techline.
DDCR_V44_DF051P/DDCR_V48_DF051P