fuse RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Owner's Manual

13B-267V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET007PRE-POSTHEATING UNIT CONTROL
STATUS
DEFINITIONACTIVE: when the heater plugs are activated according to the engine coolant
temperature.
INACTIVE: after the engine has been running for a certain period
In the event of a fault, consult the interpretation of fault DF017 Preheating unit
control circuit.
NOTESSpecial notes:
This status is specific to slow heater plugs (black ring).
Conformity check with engine stopped and ignition on.
"ACTIVE"When the ignition is switched on, status ET007 should be ACTIVE for a time that varies
according to the engine coolant temperature. Both the relay and the heater plugs are
supplied.
After starting, the status should remain ACTIVE for a time that varies according
to the engine temperature. This is the postheating phase.
If ET007 is INACTIVE when the ignition is switched on, check:
– Supply fuse FM12 (70A) of component 597 (engine fuse and relay box) or F2 (70A)
of component 777 for Mégane II and Scénic II
–The supply to the heater plugs after relay actuation, and the connections of the
heater plugs.
Important: on this engine, the plug supply voltage is variable.
– Check the continuity and absence of interference resistance of the following
connections:
•37AB between components 257 and 683,
•37AA between components 257 and 680,
•37Z between components 257 and 681,
•37AC between components 257 and 682.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
EDC16CP33_V18_ET007 / EDC16CP33_V1C_ET007 / EDC16CP33_V54_ET007 / EDC16CP33_V20_ET007 / EDC16CP33_V58_ET007 /
EDC16CP33_V5C_ET007 / EDC16CP33_V24_ET007 / EDC16CP33_V04_ET007 / EDC16CP33_V08_ET007 / EDC16CP33_V44_ET007 /
EDC16CP33_V4C_ET007 / EDC16CP33_V34_ET007 / EDC16CP33_V38_ET007 / EDC16CP33_V74_ET007 / EDC16CP33_V28_ET007 /
EDC16CP33_V26_ET007
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-287V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET143
CONTINUED 1
Conformity check with the engine running and engine coolant temperature > 80°C
INACTIVE or ACTIVE, depending on the engine temperature (air conditioning switched off).
In the event of a fault, refer to the interpretation of fault DF018.
Sensor electrical conformity
"ACTIVE"When the coolant reaches 99°C, the injection computer actuates the low-speed fan
assembly relay, and status ET143 becomes ACTIVE. The relay then supplies the
fan assembly and the cooling fan begins to turn.
If status ET143 is ACTIVE, but the cooling fan is not running, perform the following
operations:
Check the condition of fuse FM15 (60 A) in the engine fuse and relay box (see MR364
(Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis
ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List and location of
components).
Disconnect the low speed and high speed relays, check that they are operating
correctly and check the condition of the relay mounting connectors (see Wiring
Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II
ph2, Scénic II ph2, component code 597).
If one of the connectors is faulty and there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair, wiring: precautions for repair), repair the
connector, otherwise replace the wiring.
Check the + 12 V after relay supply to the low speed fan assembly relay on the
following connection:
•3FB of component 700.
Check the continuity and absence of interference resistance of the following
connections:
•49L between components 700 and 321,
•49B between components 262 and 321,
•3JN between components 700 and 120.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-290V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET144
CONTINUED 1
Sensor electrical conformity
"ACTIVE"When the coolant reaches 102°C, the injection computer actuates the fan assembly
relay and status ET144 becomes ACTIVE. The relay then supplies the cooling fan.
If status ET144 is ACTIVE, but the cooling fan is not running, perform the following
operations:
Check the condition of fuse FM15 (60 A) in the engine fuse and relay box (see MR364
(Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis
ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List and location of
components).
Disconnect the low speed and high speed relays, check that they are operating
correctly and check the condition of the relay mounting connectors (see Wiring
Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II
ph2, Scénic II ph2, component code 597).
If one of the connectors is faulty and there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair, wiring: precautions for repair), repair the
connector, otherwise replace the wiring.
Check the + 12 V after relay supply to the high-speed fan assembly relay on the
following connection:
•3FB of component 234.
Check the continuity and absence of interference resistance of the following
connections:
•3JP between components 234 and 120,
•49B between components 234 and 262.
Check that the earth is in order on connection MAS of component 262.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-316V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
CONTINUED 1
Sensor electrical conformity
"ACTIVE"
or
"INACTIVE"If the brake lights are working:
– check the continuity and the absence of interference resistance on the
following connection:
•5A between components 160 and 120 / 645 / 119.
If there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
For MEGANE II ph2 and SCENIC II ph2 with ESP:
Continuity between
connections:Insulation between
connections:
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
For MEGANE II ph2 and SCENIC II ph2 without ESP:
Continuity between
connections:Insulation between
connections:
Switch engaged
(Brake pedal released)5A BPT 65A SP17
Switch released
(Brake pedal depressed)65A SP17 5A BPT
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-442V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC031THERMOPLUNGER No. 3 RELAY
NOTESCheck that the computer is correctly configured using command LC056
Thermoplungers
There must be no present or stored faults:
Perform this fault finding procedure if there is a fault with the passenger compartment
heating - demisting.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
If the Thermoplunger no. 3 relay or the additional heater interface unit does not function when command
AC031 is run.
Check the condition of the thermoplunger 3 relay mounting on the engine fuse box or the additional heater
interface unit (see Wiring Diagram Technical Note, Vehicle, component code 1069 or 1550).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Vehicle, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
if the fault is still present, check as follows that this relay is controlled by the engine management computer:
Disconnect the thermoplunger no. 3 relay and fit a 50 Ω to 100Ω resistor on its mounting instead of the coil and
connect a voltmeter as follows:
– positive terminal to + 12 V battery,
– negative terminal to connection 3JAB of component 1069 or 1550.
Run command AC031.
If the voltmeter indicates the battery voltage (4 ON-OFF cycles of 10 seconds), replace the thermoplunger no. 3
relay.
If the voltmeter does not show the battery voltage (4 ON-OFF cycles of 10 seconds), contact the Techline.
EDC16CP33_V18_AC031 / EDC16CP33_V1C_AC031 / EDC16CP33_V54_AC031 / EDC16CP33_V20_AC031 / EDC16CP33_V58_AC031 /
EDC16CP33_V5C_AC031 / EDC16CP33_V24_AC031 / EDC16CP33_V04_AC031 / EDC16CP33_V08_AC031 / EDC16CP33_V44_AC031 /
EDC16CP33_V4C_AC031 / EDC16CP33_V34_AC031 / EDC16CP33_V38_AC031 / EDC16CP33_V74_AC031 / EDC16CP33_V28_AC031 /
EDC16CP33_V62_AC031 / EDC16CP33_V26_AC031 / EDC16CP33_V60_AC031
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-443V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
* supplier: Champion: the load resistance is between: 547 mΩ < X < 669 mΩ.
AC031
CONTINUED
If the thermoplunger no. 3 relay or the additional heater interface unit functions using command AC031,
but there is still a passenger compartment heating/demisting problem, use the wiring diagram to check:
– The conformity of the thermoplungers maxi-fuse.
– Check for + 12 V battery feed on connection BP9 of component 1069 or 1550.
– Check the conformity of heating element no. 3 relay.
– Check the continuity of connection 3JAC or 3JC between components 1069 or 1550 and 1074.
– Measure the resistance of the thermoplunger*.
– The presence of earth on the water chamber (thermoplunger mounting).
– Also check the level of the cooling circuit and that there are no leaks.
Carry out the necessary repairs.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-445V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC037
CONTINUED
STEP 2:
Check the connections of the preheating unit, component code 257, the heater plugs, component codes 680, 681,
682 and 683 and the injection computer, component code 120.
Measure the resistance of the heater plugs. If the resistance value is > 2 Ω, replace the faulty plug or plugs,
making sure that the correct plug type, slow or fast, is fitted on the vehicle.
Check the continuity and absence of interference resistance of the following connections:
•37AB between components 257 and 683,
•37AA between components 257 and 680,
•37Z between components 257 and 681,
•37AC between components 257 and 682.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition of the preheating unit supply fuse (70 A) (see MR 364 (Mégane II ph2), MR 370 (Scénic II
ph2), MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List
and location of components).
Check the + 12 V battery supply to the preheating unit on the following connection:
•BP35 of component 257.
Check the continuity and absence of interference resistance of the following connections:
•3FY between components120 and 257,
•3FF between components120 and 257.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the preheating unit.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-446V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC063THERMOPLUNGER No. 1 RELAY
NOTESThere must be no present or stored faults:
Perform this fault finding procedure if there is a fault with the passenger compartment
heating - demisting.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
If the Thermoplunger no. 1 relay or the additional heater interface unit does not function when command
AC063 is run.
Check the condition of the thermoplunger no. 1 relay mounting connector on the engine fuse box (see Wiring
Diagram Technical Note, Vehicle, component code 1067 or 1550).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Vehicle, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
if the fault is still present, check as follows that this relay is controlled by the engine management computer:
Disconnect thermoplunger no. 1 relay, and fit a 50 Ω to 100 Ω resistor on the mounting instead of the coil and
connect a voltmeter as follows:
– positive terminal to + 12 V battery,
– negative terminal to connection 3JA of component 1067 or 1550.
Run command AC063.
If the voltmeter shows the battery voltage (4 ON-OFF cycles of 10 seconds), replace the thermoplunger no. 1
relay.
If the voltmeter does not show the battery voltage (4 ON-OFF cycles of 10 seconds), contact the Techline.
EDC16CP33_V18_AC063 / EDC16CP33_V1C_AC063 / EDC16CP33_V54_AC063 / EDC16CP33_V20_AC063 / EDC16CP33_V58_AC063 /
EDC16CP33_V5C_AC063 / EDC16CP33_V24_AC063 / EDC16CP33_V04_AC063 / EDC16CP33_V08_AC063 / EDC16CP33_V44_AC063 /
EDC16CP33_V4C_AC063 / EDC16CP33_V34_AC063 / EDC16CP33_V38_AC063 / EDC16CP33_V74_AC063 / EDC16CP33_V28_AC063 /
EDC16CP33_V62_AC063 / EDC16CP33_V26_AC063 / EDC16CP33_V60_AC063
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-447V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
* supplier: Champion: the load resistance is between: 547 mΩ < X < 669 mΩ.
AC063
CONTINUED
If the Thermoplunger no. 1 relay or the additional heater interface unit functions using command AC063,
but there is still a passenger compartment heating/demisting problem, check using the wiring diagram:
The conformity of the thermoplunger maxi-fuse.
Check for + 12 V battery on connection BP9 of component 1067 or 1550.
Check the conformity of the thermoplunger no. 1 relay or the additional heater interface unit.
Check the continuity of connection 3JB between components 1067 or 1550 and 998.
Measure the resistance of the thermoplunger*.
The presence of earth on the water chamber (thermoplunger mounting).
Also check the level of the cooling circuit and that there are no leaks.
Carry out the necessary repairs.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-448V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC064THERMOPLUNGER No. 2 RELAY
NOTESThere must be no present or stored faults.
Perform this fault finding procedure if there is a fault with the passenger compartment
heating - demisting.
Consult the "Wiring diagrams" Technical Note to locate the relevant fuses and relays.
Special notes:
The thermoplunger no. 2 relay or the additional heater interface unit supplies
thermoplungers 2 and 3 in parallel.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
If the thermoplunger no. 2 relay does not operate during command AC064.
Check the condition of the thermoplunger 2 relay mounting on the engine fuse box or the additional heater
interface unit (see Wiring Diagram Technical Note, Vehicle, component code 1068 or 1550).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Vehicle, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
if the fault is still present, check as follows that this relay is controlled by the engine management computer:
Disconnect the thermoplunger no. 2 relay, fit a 50 Ω to 100 Ω resistor on its mounting instead of the coil, and
connect a voltmeter as follows:
– positive terminal to + 12 V battery,
– negative terminal on connection 3JAA of component 1068 or 1550.
Run command AC064.
If the voltmeter shows the battery voltage (4 ON-OFF cycles of 10 seconds), replace the thermoplunger no. 2
relay.
If the voltmeter does not show the battery voltage (4 ON-OFF cycles of 10 seconds), contact the Techline.
EDC16CP33_V18_AC064 / EDC16CP33_V1C_AC064 / EDC16CP33_V54_AC064 / EDC16CP33_V20_AC064 / EDC16CP33_V58_AC064 /
EDC16CP33_V5C_AC064 / EDC16CP33_V24_AC064 / EDC16CP33_V04_AC064 / EDC16CP33_V08_AC064 / EDC16CP33_V44_AC064 /
EDC16CP33_V4C_AC064 / EDC16CP33_V34_AC064 / EDC16CP33_V38_AC064 / EDC16CP33_V74_AC064 / EDC16CP33_V28_AC064 /
EDC16CP33_V62_AC064 / EDC16CP33_V26_AC064 / EDC16CP33_V60_AC064
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.