sensor RENAULT TWINGO 2009 2.G Air Conditioning User Guide

62A-33
AIR CONDITIONING
Compressor - condenser connecting pipe: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the refrigerant circuit using a refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the pressure sensor connector (1) . Equipment required
refrigerant charging station
compressed air nozzle
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair:
- (see 62A, Air conditioning, Air conditioning:
Precautions for the repair, page 62A-1) ,
- (see Vehicle: Precautions for the repair) (01D,
Mechanical introduction).
Note:
Use blanking plugs for the fuel circuits with part no.
77 01 208 229 or 77 01 476 857 to plug any open-
ings exposed to the open air. They must be clean.
Do not use any which have already been used to
plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
121174

62A-34
AIR CONDITIONING
Compressor - condenser connecting pipe: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
aRemove the bolt (2) from the « compressor -
condenser » connecting pipe on the condenser.
aSeparate the « compressor - condenser » connect-
ing pipe from the condenser.
aFit plugs into the openings.aRemove the bolt (3) from the « compressor -
condenser » connecting pipe on the compressor.
aSeparate the « compressor - condenser » connect-
ing pipe from the compressor.
aFit plugs into the openings.
aRemove the « compressor - condenser » connect-
ing pipe.
aRemove the pressure sensor on the « compressor -
condenser » connecting pipe.
121312
WARNING
In order to avoid any refrigerant leaks, do not
damage (deform, twist, etc.) the pipe.
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which
are open to the air.
121175
WARNING
In order to avoid any refrigerant leaks, do not
damage (deform, twist, etc.) the pipe.
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which
are open to the air.

62A-35
AIR CONDITIONING
Compressor - condenser connecting pipe: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
REFITTING
I - REFITTING PREPARATION OPERATION
a
aClean the surface and seal of the pipe using EN-
GINE CLEANER (see Vehicle: Parts and con-
sumables for the repair) (04B, Consumables -
Products).aUse a compressed air nozzle to blow on the sur-
face and the seal of the connecting pipe.
aLubricate the surface of the connecting pipe and the
seal with air conditioning oil (see 62A, Air condi-
tioning, Air conditioning: Parts and consum-
ables for the repair, page 62A-2) .
aRemove the blanking plugs.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the pressure sensor on the « compressor -
condenser » connecting pipe.
aFit:
-the « compressor - condenser » connecting pipe
on the compressor,
-the « compressor - condenser » connecting pipe
on the condenser.
aRefit:
-the bolt on the « compressor - condenser » con-
necting pipe on the compressor,
-the bolt on the « compressor - condenser » con-
necting pipe on the condenser.
aConnect the pressure sensor connector.
III - FINAL OPERATION
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection), WARNING
Do not remove the blanking plugs from each
component until the last moment.
Also, do not remove the components from their
packaging until they are to be fitted to the vehi-
cle.
143880
143882

62A-40
AIR CONDITIONING
Pressure sensor: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the pressure sensor connector (1) .
aRemove the pressure sensor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the pressure sensor.
aConnect the pressure sensor connector.
II - FINAL OPERATION.
aRemove:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
121174
Note:
An automatic shut-off valve isolates the circuit
from the outside during removal; do not drain the
refrigerant from the circuit.

62A-41
AIR CONDITIONING
Exterior air temperature sensor: Removal - Refitting
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the right-hand door mirror glass (see Door mirror
glass: Removal - Refitting) (MR 412, 56A, Exteri-
or equipment),
-the right-hand door mirror cover (see Door mirror
casing: Removal - Refitting) (MR 412, 56A, Exte-
rior equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the exterior air temperature sensor from its
mounting using a flat-blade screwdriver.
aCut the exterior air temperature sensor wires (see
Wiring: Repair) (Technical Note 6015A, 88A, Wir-
ing).
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aSolder the exterior air temperature sensor feed
wires (see Wiring: Repair) (Technical Note 6015A,
88A, Wiring).
aClip the external air temperature sensor onto its sup-
port.II - FINAL OPERATION.
aRefit:
-the right-hand door mirror cover (see Door mirror
casing: Removal - Refitting) (MR 412, 56A, Exte-
rior equipment),
-the right-hand door mirror glass (see Door mirror
glass: Removal - Refitting) (MR 412, 56A, Exteri-
or equipment).
101624