brake pads RENAULT TWINGO 2009 2.G Chasiss Owner's Manual

31A-23
FRONT AXLE COMPONENTS
Front driveshaft hub carrier: Removal - Refitting
31A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the front wheel on the side in question (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front brake pads of the side in question (see
31A, Front axle components, Front brake pads:
Removal - Refitting, page 31A-1) ,
aRemove:
-the front brake calliper mounting (see 31A, Front
axle components, Front brake calliper mount-
ing: Removal - Refitting, page 31A-14) ,
-the front brake disc (see 31A, Front axle compo-
nents, Front brake disc: Removal - Refitting,
page 31A-19) ,
-the front wheel speed sensor on the hub carrier
(see 38C, Anti-lock braking system, Front wheel
speed sensor: Removal - Refitting, page 38C-
15) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aPosition the (Rou. 604-01).
aRemove the hub nut (1) .
aRemove:
-the nut (2) from the track rod end,
-the bolt (3) from the lower ball joint. Special tooling required
Rou. 604-01Hub locking tool.
Tav. 476Ball joint extractor.
Tav. 1420-01Screw jack for tools Tav.
1420, Tav.1050-04 , Tar.
1454, Tar. 1850.
Tightening torquesm
shock absorber lower
bolts105 Nm
front driveshaft lower
arm ball joint bolt105 Nm
ABS wiring bracket bolt8 Nm
track rod end nut37 N.m
hub nut280 Nm
guide pin upper bolt29 Nm
119543
119222

31A-25
FRONT AXLE COMPONENTS
Front driveshaft hub carrier: Removal - Refitting
31A
aCheck that the bush (6) is correctly fitted on the front
driveshaft lower arm ball joint.
aRefit the front driveshaft lower arm ball joint bolt.
aTorque tighten the front driveshaft lower arm ball
joint bolt (105 Nm).
aRefit:
-the ABS wiring bracket,
-the ABS wiring bracket bolt.
aTorque tighten the ABS wiring bracket bolt (8 Nm).
aPosition the track rod.
aRefit the track rod end nut.
aTorque tighten the track rod end nut (37 N.m).
aRefit the hub nut using the (Rou. 604-01).
aTorque tighten the hub nut (280 Nm).
II - FINAL OPERATION
aRefit:
-the front wheel speed sensor on the hub carrier,
-the front brake disc (see 31A, Front axle compo-
nents, Front brake disc: Removal - Refitting,
page 31A-19) ,
-the front brake calliper mounting (see 31A, Front
axle components, Front brake calliper mount-
ing: Removal - Refitting, page 31A-14) .
aFit the front brake calliper.
aRefit the upper bolt on the guide pin while holding
the nut.aTorque tighten the guide pin upper bolt (29 Nm).
aRefit:
-the front brake pads (see 31A, Front axle compo-
nents, Front brake pads: Removal - Refitting,
page 31A-1) ,
-the wheel (see 35A, Wheels and tyres, Wheel:
Removal - Refitting, page 35A-1) .
119223

31A-26
FRONT AXLE COMPONENTS
Front hub carrier bearing: Removal - Refitting
31A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRemove:
-the front wheel on the side in question (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front brake pads (see 31A, Front axle compo-
nents, Front brake pads: Removal - Refitting,
page 31A-1) ,
-the calliper mounting (see 31A, Front axle com-
ponents, Front brake calliper mounting: Re-
moval - Refitting, page 31A-14) ,
-the brake disc (see 31A, Front axle components,
Front brake disc: Removal - Refitting, page 31A-
19) ,
-the front driveshaft hub carrier (see 31A, Front
axle components, Front driveshaft hub carrier:
Removal - Refitting, page 31A-23) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the hub (1) using a hydraulic press, applying force
with a pipe 65 mm (2) in diameter,
-the circlip (3) .
aRemove the internal bush (4) from the hub using an
extractor with jaws (5) . WARNING
In order to prevent irreversible damage to the front
hub bear ing:
-Do not loosen or tighten the driveshaft nut when
the wheels are on the ground.
-Do not place the vehicle with its wheels on the
ground when the driveshaft has been loosened or
removed.
WARNING
To ensure that the wheel speed sensor works prop-
erly, do not mark the sensor target on the bearing.20786
101230

31A-28
FRONT AXLE COMPONENTS
Front hub carrier bearing: Removal - Refitting
31A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the bearing using a hydraulic press, taking hold
of the outer bush with a pipe with an outer diame-
ter of 70 mm (8) .
aRefit the circlip.aRefit the hub (9) using a hydraulic press, taking hold
of the bearing's internal bush with a pipe with an
outer diameter of 50 mm (10) .
III - FINAL OPERATION.
aRefit:
-the front driveshaft hub carrier (see 31A, Front
axle components, Front driveshaft hub carrier:
Removal - Refitting, page 31A-23) ,
-the brake disc (see 31A, Front axle components,
Front brake disc: Removal - Refitting, page 31A-
19) ,
-the calliper mounting (see 31A, Front axle com-
ponents, Front brake calliper mounting: Re-
moval - Refitting, page 31A-14) ,
-the front brake pads (see 31A, Front axle compo-
nents, Front brake pads: Removal - Refitting,
page 31A-1) ,
-the front wheel on the side in question (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
114182
WARNING
Do not press the bearing's inner bush so as to
avoid damaging the bearing (very high shrink-fit-
ting force).
Note:
the black side of the bearing must be fitted on the
circlip side.
114183

33A-1
REAR AXLE COMPONENTS
Rear brake pads: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
When replacing brake pads, be sure to replace the
pads on the opposite side.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRelease the parking brake.
aRemove the rear wheels (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the parking brake cable from the brake calli-
per at (1) .
aMove aside the parking brake cable.
aRemove the lower bolt (2) of the brake calliper guide
pin.
aTilt the brake calliper over.
aRemove the brake pads (3) from the brake calliper
mounting. Special tooling required
Fre. 1190-01Brake calliper piston return
tool.
Tightening torquesm
new lower bolts of the
calliper guide pins35 N.m
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468
132466

33A-2
REAR AXLE COMPONENTS
Rear brake pads: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
aRemove the noise-reducing blades (4) from the
brake calliper mounting.
REFITTING
I - REFITTING PREPARATION OPERATION
aClean using a wire brush and BRAKE CLEANER
(see Vehicle: Parts and consumables for the re-
pair) (04B, Consumables - Products):
-the calliper supports,
-the callipers.
aAlways replace the brake calliper guide pin bolts.aPush the piston to the bottom of its housing using
the (Fre. 1190-01).
aRemove the protective film from the brake pad.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the noise-reducing fins onto the brake calliper
mountings,
-the brake pads onto the brake calliper mountings.
132464106309
127485

33A-3
REAR AXLE COMPONENTS
Rear brake pads: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
aFit:
-the brake callipers,
-the parking brake cables.
aTorque tighten the new lower bolts of the calliper
guide pins (35 N.m).
aClip on the handbrake cables.
III - FINAL OPERATION
aRefit the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
IMPORTANT
To avoid any accident, bring the pistons, brake
pads and brake discs into contact by depressing
the brake pad several times.

33A-8
REAR AXLE COMPONENTS
Rear brake calliper: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
aPush the piston to the bottom of its housing using
the (Fre. 1190-01).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the brake calliper on the calliper mounting.
aTorque tighten:
-the new bolts on the brake calliper guide pins
(35 N.m),
-the brake pipe union on the calliper (13 N.m).
aFit the parking brake cable.
aClip the handbrake on the brake calliper.
III - FINAL OPERATION
aRefit the rear wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aRemove the pedal press from the brake pedal.
aBleed the brake circuit (see 30A, General informa-
tion, Braking circuit: Bleed, page 30A-4) .
106309
IMPORTANT
To avoid any accident, bring the pistons, brake
pads and brake discs into contact by depressing
the brake pad several times.

33A-9
REAR AXLE COMPONENTS
Rear brake calliper mounting: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRelease the parking brake.
aRemove:
-the rear wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the rear brake pads (see 33A, Rear axle compo-
nents, Rear brake pads: Removal - Refitting,
page 33A-1) .aRemove:
-the brake calliper guide pin bolts (1) ,
-the brake calliper from the mounting.
aAttach the brake calliper to the suspension spring.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the brake calliper mounting bolts (2) ,
-the brake calliper mounting. Special tooling required
Fre. 1190-01Brake calliper piston return
tool.
Tightening torquesm
bolts of the brake calli-
per mountingXXX
new bolts of the brake
calliper guide pins105 N.m
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468
132465

33A-10
REAR AXLE COMPONENTS
Rear brake calliper mounting: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
REFITTING
I - REFITTING PREPARATION OPERATION
aClean using a wire brush and BRAKE CLEANER
(see Vehicle: Parts and consumables for the re-
pair) (04B, Consumables - Products):
-the calliper supports,
-the callipers.
aAlways replace:
-the calliper mounting bolts,
-the calliper guide pin bolts.
aPush the piston to the bottom of its housing using
the (Fre. 1190-01).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the brake calliper mounting.
aTorque tighten the bolts of the brake calliper
mounting (XXX).
III - FINAL OPERATION.
aRefit:
-the brake calliper,
-the brake pads (see 33A, Rear axle components,
Rear brake pads: Removal - Refitting, page 33A-
1) .
aTorque tighten the new bolts of the brake calliper
guide pins (105 N.m).aRefit the rear wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
106309
IMPORTANT
To avoid any accident, bring the pistons, brake
pads and brake discs into contact by depressing
the brake pad several times.