Valve RENAULT TWINGO 2009 2.G Electrical Equipment - Petrol Injection Manual PDF

17B-335V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC117UPSTREAM O2 SENSOR HEATING
NOTESThere must be no present or stored faults.
Run command AC117.
Using a multimeter, check for 10 earthings on connection 3GH of the upstream O2 sensor.
SIM32_V44_AC117 / SIM32_V4C_AC117 / SIM32_V50_AC117 / SIM32_V54_AC117
AFTER REPAIRIf the throttle valve has been replaced, reinitialise the RZ005 programming.
Carry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-336V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC118DOWNSTREAM O2 SENSOR HEATING
NOTESThere must be no present or stored faults.
Run command AC118.
Using a multimeter, check for 10 earthings on connection 3GJ of the downstream O2 sensor.
SIM32_V44_AC118 / SIM32_V4C_AC118 / SIM32_V50_AC118 / SIM32_V54_AC118
AFTER REPAIRIf the throttle valve has been replaced, reinitialise the RZ005 programming.
Carry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-337V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
AC180AIR CONDITIONING COMPRESSOR RELAY CONTROL
NOTESSpecial notes:
There must be no present or stored faults.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Check the condition of the connectors of the air conditioning compressor clutch relay (component code 584) and
of the engine management computer (component code 120).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
With the ignition, check for + 12 V on connection 3FB of the air conditioning compressor clutch relay and the
earthing of connection 38K on the injection computer connector.
Use the universal bornier to check the insulation and continuity of the following connections:
●3FB between components 584 and 238,
●38K between components 584 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the control still does not operate, run a diagnostic check on the Heating system.
(see 62A, Heating, 62B, Climate control or 62C, Manual air conditioning).
SIM32_V44_AC180 / SIM32_V4C_AC180 / SIM32_V50_AC180 / SIM32_V54_AC180
AFTER REPAIRIf the throttle valve has been replaced, reinitialise the RZ005 programming.
Carry out a road test, then check with the diagnostic tool.

17B-338V7 MR-413-X44-17B000$190.mif
PETROL INJECTION
Fault finding – Interpretation of commands17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
Only Vdiag 4C
AC199CONTROLLED COOLANT THERMOSTAT
NOTESThere must be no present or stored faults.
Run command AC199.
Using a multimeter, check for 10 earthings on connection 3VL of the controlled coolant thermostat.
SIM32_V4C_AC199
AFTER REPAIRIf the throttle valve has been replaced, reinitialise the RZ005 programming.
Carry out a road test, then check with the diagnostic tool.

17B-339V7 MR-413-X44-17B000$200.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
NOTESOnly refer to the customer complaints after performing a complete check using the
diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle valve
faults.
NO DIALOGUE WITH THE COMPUTER ALP1
THE ENGINE WILL NOT START ALP2
IDLING SPEED FAULTSALP3
FAULTS WHILE DRIVINGALP4
Noise when cold (K4M)Technical
Note 6506A
ALP 1
Oil leak from the camshaft dephaser Technical
Note 6506A
ALP 7
Oil leak from the camshaft dephaser solenoid valveTechnical
Note 6506A
ALP 8
PETROL INJECTION
Fault finding – Customer complaints

17B-344V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP3 Idle speed faults
NOTESApply ALP3 after a complete check using the diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle
valve faults.
Check that the oil level is not too high.
Check the inlet system sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery circuit (manifold - cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Measure the electrical resistance of the quadruple ignition module.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP03 / SIM32_V4C_ALP03 / SIM32_V50_ALP03 / SIM32_V54_ALP03
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-345V7 MR-413-X44-17B000$210.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ALP4 Faults occurring while driving
NOTESApply ALP4 after a complete check using the diagnostic tool.
WARNING:
Never drive the vehicle without checking first that there are no throttle
valve faults.
Check that the oil level is not too high.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Check inlet line sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery system (manifold/cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the tank vent is not blocked.
Check the conformity of the fuel in the tank, apply test 1 Petrol conformity check.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
SIM32_V44_ALP04 / SIM32_V4C_ALP04 / SIM32_V50_ALP04 / SIM32_V54_ALP04
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.