airbag RENAULT TWINGO 2009 2.G Trim And Upholstery Workshop Manual

71A-1
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) .
aRemove:
-the front seats completely (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) ,
-the rear seats completely (depending on equip-
ment level) (see 76A, Rear seat frames and me-
chanisms, Complete rear seat: Removal -
Refitting, page 76A-1) ,
-the rear bench seat base (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seat base: Removal - Refit-
ting, page 76A-6) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) ,
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment),-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the front door sill lining (see 71A, Body internal
trim, Front door sill lining: Removal - Refitting,
page 71A-7) .
aRemove:
-the bolt (1) ,
-the storage compartment under the front seat. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121608

71A-2
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
71A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the centring pin (2) from the centre console,
-the clip (3) ,
-the floor carpet.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the seat wiring.
aRefit:
-the floor carpet,
-the clip (3) ,
-the centre console centring pin (2) .II - FINAL OPERATION.
aRefit:
-the storage compartment under the front seat,
-the bolt (1) ,
-the front door sill lining (see 71A, Body internal
trim, Front door sill lining: Removal - Refitting,
page 71A-7) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment),
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) ,
-the rear bench seat base (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seat base: Removal - Refit-
ting, page 76A-6) ,
-the rear seats completely (depending on equip-
ment level) (see 76A, Rear seat frames and me-
chanisms, Complete rear seat: Removal -
Refitting, page 76A-1) ,
-the front seats completely (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) .
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
121162

71A-4
BODY INTERNAL TRIM
Headlining: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aPartially remove the front side door and tailgate
seals.aUnclip the trim piece (1) from the sun visor shutter
cross member mounting.
aRemove:
-the finishing seal (2) from the sunroof
-the sunroof switch plate (see Sunroof switch: Re-
moval - Refitting) (MR 411, 87D, Electric window
winders - Sunroof).
aRemove:
-the interior lights (see Interior light: Removal -
Refitting) (MR 411, 81B, Interior lights),
-the sun visors (see Sun visor: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-9) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) (MR 412, 76A, Rear seat frame
and runners),
-the rear parcel shelf side trim panels (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) ,
-the rear panel trims (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) , Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
OPENING ROOF
121712

71A-6
BODY INTERNAL TRIM
Headlining: Removal - Refitting
71A
aRefit the headlining (this operation requires two peo-
ple).
aRefit clips (4) .
III - FINAL OPERATION.
aRefit the interior light and sunroof wiring harnesses
(depending on equipment level).
aConnect the interior light and sunroof connectors (3)
(depending on equipment level).
aRefit:
-the interior lights (see Interior light: Removal -
Refitting) (MR 411, 81B, Interior lights),
-the sun visors (see Sun visor: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-9) ,
-the rear quarter panel trims (see 71A, Body inter-
nal trim, Quarter panel trim: Removal - Refit-
ting, page 71A-12) .
-the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-10) ,
-the rear panel trims (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim panels (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) (MR 412, 76A, Rear seat frame
and runners),aRefit:
-the sunroof switch plate (see Sunroof switch: Re-
moval - Refitting) (MR 411, 87D, Electric window
winders - Sunroof),
-the sunroof finishing seal (2) .
aFit the sun visor headlining cross member mounting
trim piece (1) .
aRefit the front side door and tailgate seals.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners). OPENING ROOF
OPENING ROOF

75A-1
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the front seatback frame (see 75A, Front seat fra-
mes and mechanisms, Front seatback frame:
Removal - Refitting, page 75A-2) ,
-the front seat runners (see 75A, Front seat frames
and mechanisms, Front seat runner: Removal -
Refitting, page 75A-6) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seatback frame (see 75A, Front seat fra-
mes and mechanisms, Front seatback frame:
Removal - Refitting, page 75A-2) ,
-the front seat runners (see 75A, Front seat frames
and mechanisms, Front seat runner: Removal -
Refitting, page 75A-6) .
II - FINAL OPERATION.
aRefit:
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners),
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the entire front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Remo-
val - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners). Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.

75A-2
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners).aRemove:
-the bolts (1) ,
-the lumbar support. Equipment required
Diagnostic tool
Tightening torquesm
front seatback frame
bolts46 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121033

75A-5
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
75A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the front seatback frame bolts (5) ,
-the front seatback frame.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the front seatback frame bolts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seatback frame,
-the front seatback frame bolts (5) .
aTorque tighten the front seatback frame bolts (46
Nm).III - FINAL OPERATION.
aRefit:
-the unlocking cables to the front seat runners,
-the casing (4) .
-the rivets (3) ,
-the mounting for the control accessing the rear
seats (depending on the equipment level).
-the rivets (2) ,
-the seat back inclination control cable(s) (depen-
ding on the equipment level).
-the seat back inclination control cable upper
stop(s) (depending on the equipment level),
aClip on the various seat back inclination control ca-
ble lower stops (depending on the equipment level).
aRefit:
-the lumbar support,
-the bolts (1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the complete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).
120849

75A-6
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (88C, Airbags
and pretensioners).aRemove the unlocking cable from the front seat run-
ners.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the nuts (1) from the front seat runner,
-the front seat runners.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the front seat runner nuts. Equipment required
Diagnostic tool
Tightening torquesm
front seat runner nuts25 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120852
120850

75A-7
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting
75A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seat runners without tightening them,
-the front seat runner control (2) .
aObserve the tightening order:
-the runner on the vehicle interior side (3) ,
-the runner on the vehicle exterior side (4) .
aTighten:
-the runners, holding them towards the interior of
the seat at (5) and (6) ,
-to torque the front seat runner nuts (25 Nm) (1) .
III - FINAL OPERATION.
aRefit:
-the unlocking cable of the front seat runners,
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (88C, Airbags
and pretensioners),
-the entire front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Remo-
val - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents)(88C, Airbags and pretensioners).
127773

75A-8
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).aUnclip the cover (1) located under the front seat.
aDisconnect the connector (2) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the blanking covers (3) ,
-the front seat nuts (3) . Equipment required
Diagnostic tool
Tightening torquesm
front seat nuts35 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120814
121326