lights RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Owner's Manual

87B-55
MR-413-X44-87B000$432.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
With automatic headlighting:DF109
PRESENT
OR
STORED
REAR FOG LIGHTS CONTROL CIRCUIT
CC.1: Short circuit to + 12 volts
CC.0: Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
The ignition is switched on and the rear fog lights are activated.
OR
Running AC009 Rear fog lights.
Note:
This fault only appears on vehicles fitted with automatic daytime running lights. Check
the presence of the rain/light sensor (component code 1415), then:
Check that the vehicle is configured with a rain/light sensor (component code 1415):
–Check that LC044 Rain/light sensor displays Present. If not, perform CF035
Rain/light sensor.
–Check that LC096 Automatic wiper function displays With. If not, carry out
CF194 "Automatic wiper function".
–Check that LC095 Automatic headlight function displays With. If not, carry out
CF193 "Automatic headlight function".
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), F39 (10 A) in the passenger
compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the presence and condition of the rear fog lights relay (component code 230) (20A).
Replace the rear fog lights relay (component code 230) if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
connection of the UCH PE2 connector (component code 645) (tabs bent, oxidised, broken).
Check the condition and connection of the control stalk connector (component code 209) (tabs bent, oxidised,
broken).
Check for + 12 V (when there is a rear fog lights request) on connection 9P of components 172 and 173.
Check for earth on connection MF of component 172 and connection MYH on component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF109
MR-413-X44-87B000$432.mif
UCH
Vdiag No.: 44

87B-56
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF109
CONTINUED
Rear fog lights and rear fog light relay check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
Right-hand rear fog light:
●Connection code 9P between components 172 and 230.
Left-hand rear fog light:
●Connection code 9P between components 173 and 230.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V (when there is a rear fog lights request) on connection 9W of component 230. Check for + 12 V
on connection BP16 of component 230.
Rear fog lights relay check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 9W between components 230 and 645.
●Connection code BP16 between components 230 and 1016.
Control stalk check (component code 209):
Check the insulation, continuity and the absence of interference resistance of the following connections:
Check between the control stalk (component code 209) and the UCH (component code 645):
●Connection code 9B between components 645 and 209.
Check between the control stalk (component 209) and the passenger compartment fuse and relay box
(component code 1016):
●Connection code BPA2 between components 209 and 1016.
●Connection code BPA3 between components 209 and 1016.
Connection code MAM (for right-hand drive vehicles) or MAN (for left-hand drive vehicles) between component
209 and earth MAM (for right-hand drive vehicles) or MAN (for left-hand drive vehicles).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connections BPA2 and BPA3 of component 209.
Check for earth on connection MAM (for right-hand drive vehicles) or MAN (for left-hand drive vehicles) of
component 209.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supplies and connections of the control stalk (component code 209) are correct, replace the control stalk
(component code 209). (See MR 411 Mechanical 84A, Control - Signals, Lighting - signals switch: Removal
- Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

87B-60
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF134
PRESENT
OR
STOREDHAZARD WARNING LIGHTS INDICATOR LIGHT CIRCUIT
CC.0: Short circuit to earth or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
Switching on the ignition and pressing the hazard warning lights button.
OR
Activating AC52 Hazard warning lights indicator light.
Note: If the hazard warning lights do not light up during emergency braking, check
that LC018 Illumination of hazard warning lights by ABS is definitely With.
Otherwise, run CF024 Illumination of hazard warning lights by ABS.
Check the presence and condition of fuse F42 (10 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the central door locking/warning switch connector (component code
1391) (tabs broken, bent, oxidised).
Check the condition and connection of connectors PE1 and PE2 of the UCH (component code 645) (tabs bent,
oxidised, broken).
Check for + 12 V on connection LPD of the locking/warning switch (component code 1391).
Check for earth on connection MAN of the locking/warning switch (component code 1391).
If the connector or connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Switch check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 64F between components 1391 and 645.
●Connection code 64Q between components 1391 and 645.
●Connection code MAN between component 1391 and earth MAN.
●Connection code LPD between components 1391 and 1016.
●Connection code 20AM between components 1391 and 645.
●Connection code 20AW between components 1391 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supply, earth and connections are correct, replace the door locking/warning switch (component code
1391) (see MR 411 Mechanical 84A, Control - Signals, Hazard warning lights and central door locking:
Removal - Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF134

87B-61
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF135
DF136
PRESENT
OR
STOREDRAIN DETECTOR
LIGHT SENSOR
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
Switching on the ignition, activating automatic headlight lighting by moving the control
stalk twice in quick succession as follows: control stalk (component code 209) to
position zero ΑΕ control stalk (component code 209) to side lights position.
Status ET114 "Wiper request from rain sensor" should be "Low speed" or "High
speed" when the water runs over the position of the rain/light sensor on the
windscreen or status ET115 "Request for lights to be switched on from light
sensor" should be "Present" when an opaque cover is placed over the rain/light
sensor.
Note:
If there is an open circuit on connection BPT, there will be a malfunction on the
electric window winders, on the rain/light sensor, on the interior lights and the boot
lighting.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the vehicle is configured with a rain/light sensor (component code 1415).
Check that LC044 Rain/light sensor is Present. If not, perform CF035 Rain/light sensor.
Check that LC096 Automatic wiper function displays With. If not, carry out CF194 "Automatic wiper
function".
Check that LC095 Automatic headlight function displays With. If not, carry out CF193 "Automatic headlight
function".
Check the condition and position of supply fuses F2 (15 A), F8 (15 A), F19 (5 A), F27 (5 A) according to the
equipment, F29 (15 A) of the rain/light sensor (component code 1415) on the passenger compartment fuse and
relay box (component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 3-track connector of the rain/light sensor (component 1415) (tabs
bent, broken or oxidised).
Check the condition and connection of the PE2 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF135 / UCH_V44_DF136

87B-65
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF139
PRESENT
OR
STOREDCOURTESY LIGHT
CC.1: Short circuit to + 12 volts
NOTESThe fault is declared present after:
Opening at least one door.
OR
Running AC063 Switching the interior lights on and off.
Check the correct operation of status ET463 Door(s) or tailgate.
Check the condition and connection of the 6-track connector of the front interior lighting (component code 213)
and connector PE1 of component 645 (tabs bent, oxidised, broken).
Check for + 12 V on connection BPT of component 213.
Check the continuity and insulation of the following connections:
●Connection code BTP, between components 213 and 645.
●Connection code 13E between components 213 and 645.
●Connection code MAM between component 213 and earth MAM.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the operation of the rabbet switches using ET463 Door(s) and tailgate.
If the supply, earths and connections are correct, replace the courtesy light (component code 213).
(See MR 411, Mechanical 81B, Interior lighting, courtesy light: Removal - Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF139

87B-74
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: USER SELECTION
* CPE: Electric central door locking.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
User selectionET028:Heated rear screen
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET028.
ET029:Air conditioning
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET029.
ET015:Passenger
compartment blowerRUNNING
STOPPEDIn the event of a fault, refer to
the interpretation of status
ET015.
AC015:Air conditioning
button indicator lightThis command is used to test
the operation of the air
conditioning button indicator
light.In the event of a fault, refer to
the interpretation of DF042.
AC019:Heated rear screen
indicator lightThis command is for testing
operation of the heated rear
screen indicator light.In the event of a fault, refer to
the interpretation of DF041.
AC020:CPE* button
indicator lightThis command is used to
operate the electric central
locking button.In the event of a fault, refer to
the interpretation of DF082.
AC052:Hazard warning
lights indicator lightThis command is used to
activate the hazard warning
lights.In the event of a fault, refer to
the interpretation of DF134.

87B-77
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
LIGHTING FUNCTION
SUB-FUNCTION: LIGHTING CONTROL
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Lighting controlET081:Lighting switch
positionSIDE
DIPPED
MAIN BEAM
HEADLIGHTS
HAZARD LIGHTSIn the event of a fault, refer to the
interpretation for status ET081.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASEDIn the event of a fault, refer to the
interpretation for status ET085.
Lighting requestET115:Request to switch on
lights by light sensorPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET115.
ET111:Front fog lights
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET082.
ET083:Left-hand indicator
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation of statuses
ET083 and ET084.
ET084:Right-hand indicator
requestPRESENT
ABSENT
TailgateET463:Door(s) or tailgateOPEN
CLOSEDIn the event of a fault, consult the
interpretation of status ET463.
Vehicle speedPR008:Vehicle speed0 mphIn the event of a fault, run fault
finding on the ABS system (see
38C, Anti-lock braking system).

87B-78
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: LIGHTING OUTPUT
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Front fog lightsAC008:Front fog lightsThis command is used to
activate the front fog
light.In the event of a fault, apply the
interpretation of DF108.
Rear fog lightsAC009:Rear fog lightsThis command is used to
activate the rear fog light.In the event of a fault, apply the
interpretation of DF109.
Direction indicatorsAC022:Left-hand
direction
indicatorsThis command is used to
activate the left-hand
direction indicators.In the event of a fault, refer to the
interpretation for fault DF013
Left-hand direction indicator
circuit.
AC023:Right-hand
direction
indicatorsThis command is used to
activate the right-hand
direction indicators.In the event of a fault, refer to the
interpretation for fault DF012
Right-hand direction indicator
circuit.
LightsAC055:Side lightsThis command enables the
side lights to be activated.In the event of a fault, apply the
interpretation of DF087.
AC054:Dipped
headlightsThis command enables the
dipped beam headlights to
be activated.In the event of a fault, apply the
interpretation of DF088.

87B-79
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: LIGHTING OUTPUT (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Lights (continued)AC062:Main beam
headlightsThis command enables the
headlights to be activated.In the event of a fault, apply the
interpretation of DF098.
AC063:Progressive
switching on and off
of the courtesy lightThis command is used to
check that the gradual
courtesy light activation and
deactivation function is
operating correctly.In the event of a fault, apply the
interpretation of DF139.
Temperature
displayAC110:Temperature display Controls the display.In the event of a fault, apply the
interpretation of command
AC110.

87B-84
MR-413-X44-87B000$528.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
*CPE: Electric central door locking
*RF: radio frequencyTool status Diagnostic tool title
ET008Blank UCH
ET015Passenger compartment blower
ET027Windscreen wiper park position
ET028Heated rear screen button
ET029Air conditioning button
ET030Air conditioning request 2
ET044CPE* button
ET045RF* signal. received
ET046Engine immobiliser
ET047Brake pedal position
ET061Open tailgate request
ET077Wiper stalk position
ET078Windscreen washer request
ET079Rear screen washer request
ET080Rear screen wiper request
ET081Lighting switch position
ET082Rear fog lights request
ET083Left-hand indicator request
MR-413-X44-87B000$528.mif
UCH
Vdiag No.: 44