lights RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Service Manual

87B-117
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET085
CONTINUED
Lights check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
Front right-hand lights:
●Connection code 64D between components 255 and 645.
●Connection code MAR between component 1391 and earth MAR.
Front left-hand lights:
●Connection code 64D between components 256 and 645.
●Connection code MAS between component 1391 and earth MAS.
Right-hand repeater:
●Connection code 64D between components 267 and 645.
●Connection code MAR between component 1391 and earth MAR.
Left-hand repeater:
●Connection code 64D between components 268 and 645.
●Connection code MAN between component 1391 and earth MAN.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supplies, earths and connections are correct, replace the component concerned.
Check for + 12 V on connection LPD of component 1391.
Check for earth on connection MAN of component 1391.
Switch check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 64F between components 1391 and 645.
●Connection code 64Q between components 1391 and 645.
●Connection code MAN between component 1391 and earth MAN.
●Connection code LPD between components 1391 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supply, earth and connections are correct, replace the door locking/warning switch (component code
1391). (see MR 411 Mechanical 84A, Control - Signals, Hazard warning lights and central door locking:
Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B -124
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET109
REVERSE GEAR ENGAGED
NOTESThere must be no present or stored faults.
Check the presence and condition of fuse F6 (15 A) on the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 2-track connector on the switch connector (component code 155) of
the reversing lights (component code 155) (tabs bent, broken, oxidised).
Check the condition and connection of the PE1 40-track UCH connector, (component code 645) (tabs bent,
broken, oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection AP3 of the reversing lights switch connector.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the switch pressed, check the continuity between connections AP3 and H66P of component 155.
With the switch released, check the insulation between connections AP3 and H66P of component 155.
If these checks are not correct, replace the reverse gear switch (component code 155) if necessary.
If these checks are correct, check the insulation, continuity and the absence of interference resistance on
the following connections:
●Connection code AP3 between components 155 and 1016.
●Connection code HP66P between components 155 and 172.
●Connection code HP66P between components 155 and 173.
●Connection code HP66P between components 1222 and 155.
●Connection code HP66P between components 645 and 155.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring or replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET109

87B -125
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
With automatic headlighting:ET111
FRONT FOG LIGHTS REQUEST
NOTESThere must be no present or stored faults.
Check that the LC015 Front fog lights is definitely With. Otherwise, use command
CF021 Front fog lights.
Note:
The signal can only be interpreted if the function is managed by the UCH (component
code 645) (vehicle equipped with one-touch fog light control).
SPECIFICATIONSPRESENT
ABSENT
Use AC008 Front fog lights to check that the front fog lights operate correctly.
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), in the passenger compartment fuse
and relay box (component code 1016).
Replace the fuse if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the front fog light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the PE2 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
Check the condition and connection of the control stalk connector (component code 209) (tabs bent, oxidised,
broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V (when there is a rear fog lights request) on connection 8B of components 176 and 177. Check
for earth on connection MAR of component 176 and connection MAS of component 177.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET111

87B -126
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET111
CONTINUED 1
Front fog lights check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
Right-hand light and front right-hand fog light relay:
●Connection code 8B, between components 176 and 231.
Front left-hand light and front left-hand fog light relay:
●Connection code 8B, between components 177 and 231.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V (when there is a front fog lights request) on connection 8M of component 231. Check for + 12 V
on connection BP16 of component 231.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Front fog lights relay check:
Check the insulation, continuity and the absence of interference resistance of the following connections:
●Connection code 8M between components 231 and 645.
●Connection code BP16 between components 231 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B -128
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET114
ET115
WIPER REQUEST BY RAIN SENSOR
LIGHT ACTIVATION REQUEST BY LIGHT SENSOR
NOTESThere must be no present or stored faults.
Make sure that the vehicle is fitted with the rain and light sensor.
The status should change to LOW SPEED or HIGH SPEED if there is water on the
windscreen where the sensor is positioned.
The status should change to PRESENT when the light intensity requires the lights to
be switched on with the engine running.
Make sure that the other positions of the wiper control are working properly
Check the following configurations:
–Check that LC008 Daytime running lights is "With". Otherwise run CF014
Daytime running lights.
–Check that LC044 Rain/light sensor displays "Present". If not, run CF035 Rain/
light sensor.
–Check that LC095 Automatic headlight function displays "With". If not, run
CF193 Automatic headlight function.
–Check that LC096 Automatic wiper function displays With. If not, run CF194
Automatic wiper function.
SPECIFICATIONSET114: ABSENT/LOW SPEED/HIGH SPEED
ET115: PRESENT/ABSENT
Conditions:
Check that the switch stalk (component code 209) is in the intermittent position so that automatic operation can
be activated.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the function is not deactivated, perform the following cycle twice to activate the automatic headlight
function: Switch stalk (component code 209) OFF → Σωιτχη σταλκ (χοµπονεντ χοδε 209) to side lights ON
position.
Check the condition and connection of the 3-track connector of the rain/light sensor (component 1415) (tabs
bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET114 / UCH_V44_ET115

87B -141
MR-413-X44-87B000$624.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
Special feature: Depending on the vehicle equipment, an additional fuse and diode are present on the
wiring: ET463
CONTINUED 2
Check the insulation, continuity and the absence of interference resistance of the following connections:
Central door locking/warning switch check (component code 1391):
●Connection code 20AW between components 645 and 1391.
●Connection code 20M between components 645 and 1391.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the central door locking/warning switch (component code 1391).
(See MR 411 Mechanical 84A, Control - Signals, Hazard warning lights and central door locking:
Removal - Refitting).
With the engine running, check that the door
open warning (buzzer) is active when the driver
door is open and the lights are on.
Is the warning active?
NO
Check the continuity of connection H24 between
components 140 and 1016 and between
components 119 and 1016.
Is the continuity correct?
NO
C
YESB

87B -143
MR-413-X44-87B000$624.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
ET463
CONTINUED 4
Check that the diode is fitted the right way
round (in accordance with the foolproofing
device).
Is the diode fitted the wrong way round?
Fit a diode the right way round in the correct
location in the passenger compartment fuse
box.
(see MR 411 Mechanical, 81C, Fuses,
Fuses: List and location of components)
A disconnected earth causes damage to
the fuse. If the diode and/or the fuse are
damaged, the tailgate earth (MYH) and the
passenger door earth (MAN and MAM)
should be checked.
If the earths are correct, replace the
diode and/or the fuse in the passenger
compartment fuse box (see MR 411
Mechanical, 81C, Fuses, Fuses: List and
location of components)Check the continuity of connection 86H between
components 1016 and 645.
If the connection or connections are faulty and there is
a repair procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the wiring is in order, replace the driver's door switch
(component code 140) (see MR 411 Mechanical
systems, 81B, Interior lights, Door switch:
Removal - Refitting)
A
YES
NO
B
DB
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B -155
MR-413-X44-87B000$816.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
UCH
Vdiag No.: 44
87B
AC004
AC005
CONTINUED 3
Check the insulation, continuity and the absence of interference resistance on the following connections:
Central door locking/warning switch check:
●Connection code 20AW between components 645 and 1391.
●Connection code 20M between components 645 and 1391.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the central door locking/hazard warning lights switch (Component code
1391). (See MR 411 mechanical systems 84A, Controls - Signals, Hazard warning lights and central door
locking: Removal - Refitting).
If the fault is still present, replace the door lock affected (passenger door lock (component code 141) or
passenger door lock (component code 140)).
AFTER REPAIRCarry out another fault finding check on the system.

87B -164
MR-413-X44-87B000$864.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
NOTESSpecial notes:
This summary corresponds to the complete list of customer complaints for a UCH.
These customer complaints are divided by function in the section corresponding to the
function concerned.
DIALOGUE FAULT87B
NO DIALOGUE WITH THE COMPUTER ALP 1
LIGHTING80D
NO REAR FOG LIGHTS ALP 2
NO RIGHT-HAND DIRECTION INDICATOR ALP 3
NO LEFT-HAND DIRECTION INDICATOR ALP 4
NO SIDE LIGHTS ALP 5
NO DIPPED BEAM HEADLIGHTS ALP 6
NO HEADLIGHTS ALP 7
NO FRONT FOG LIGHTS ALP 8
LIGHTS DO NOT SWITCH OFF AFTER + AFTER IGNITION
FEED IS CUT AND DRIVER'S DOOR IS OPENEDALP 9
LIGHTS DO NOT SWITCH ON AT NIGHT ALP 10
NO SEE-ME-HOME LIGHTING ALP 11
NO COURTESY LIGHTS ALP 12
MR-413-X44-87B000$864.mif
UCH
Vdiag No.: 44