interior lights RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Workshop Manual

87B-7
MR-413-X44-87B000$096.mif
V5
87B
ENGINE HARNESS
FRONT ENGINE WIRING & ADDITIONAL HEADLIGHTS
DOOR WIRING
CEILING WIRING
PASSENGER COMPARTMENT WIRING
REAR BUMPER WIRING
TAILGATE WIRING
1UCH
2Passenger Compartment Relay/Fuse Box
3Electric power-assisted steering.
4Transponder ring.
5Air conditioning panel.
6One touch window/anti-pinch module.
7Exterior temperature sensor.
8Rain/light sensor & interior temperature sensor.
9Anti-pinch/sunroof.
2ABS computer.
2Injection computer.
3Preheating unit.
4Sequential gearbox computer.
5Engine fuse and relay box.
6Alternator.
7
2
61
2
3
5
4
8
5
7
43
1
6
9
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding
- List and location of components
MR-413-X44-87B000$096.mif
UCH
Vdiag No.: 44

87B-12
MR-413-X44-87B000$192.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Role of components87B
CONTINUED (Functions managed by the different UCH ranges on the New Twingo):
L1
Entry levelL2
Mid-rangeL3
Top of the
range
Lighting
Exterior lighting
Side, dipped beam, headlightsX
Direction indicators and hazard warning lightsXX X
One-touch front fog lightsX
One-touch rear fog lightsX
Lights on warning lightXX X
Hazard warning lights when decelerating hardXX X
Illumination of hazard warning lights when airbag triggeredXX X
Illumination of indicators when locking/unlockingXX
Automatic lighting when driving and stationaryX
Delayed extinction of headlights when stationary X
Daytime running lights onX
Lights switch off when driver's door openedX
Interior lighting
Interior lights supply (no gradual dimming function)X
Interior lights supply (gradual dimming)XX
Wipers
Windscreen wipers managementXX X
Automatic management of front wipers with rain sensorX
Rear wipersXX X
Windscreen and rear screen washersXX X
Energy management
Starter managementXX X
Controlled alternator (BSS connection)XX X

87B-21
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Functions available and operating mode
–Deadlocking (CF009)
This function enables you to disable the interior door opening control. This function is activated by a second locking
request from the key or the electric central locking switch.
This function is only available on vehicles fitted with a top of the range UCH.
–Hazard warning lights activated by ABS (CF024)
This function is available for all countries except Brazil, Finland, Great Britain, Japan and Sweden.
For Brazil, Great Britain, Japan, Sweden and Finland configure NONE.
For other countries, configure WITH.
In the event of braking causing rapid deceleration, the ABS computer transmits an activate hazard warning lights
request via the multiplex network to the UCH.
–New vehicle storage mode (LC041 New vehicle storage mode)
If this mode is activated, consult the command, see LC041 "New vehicle storage mode" and contact the Techline.
–Daytime running lights
This configuration automatically activates the side lights and dipped beam headlights when the engine is running,
without the driver using the lighting controls.
To be used in accordance with legislative requirements.
CF031 Calibration:
When replacing the UCH computer, perform this configuration.
This command lasts approximately 30 seconds.

87B-24
MR-413-X44-87B000$336.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
Summary of sensors and actuators on which the UCH can carry out fault finding (with the corresponding
engineering office codes).
Tool fault Associated DTC Diagnostic tool title
DF0019510 UCH
DF0119522 Rain/light sensor circuit
DF01295D1 Right-hand direction indicator circuit
DF01395D0 Left-hand direction indicator circuit
DF0279550 External temperature sensor circuit
DF04095A0 Rear screen wiper park position
DF0419560 Heated rear screen warning light circuit
DF0429558 Air conditioning warning light circuit
DF0549501 Computer
DF0629580 Starter relay control circuit
DF06595F0 Electric window authorisation connection
DF0829570 Door locking button indicator light circuit
DF08795C2 Side lights relay control circuit
DF08895C3 Dipped beam headlights relay control circuit
DF09795 A1 Windscreen wiper park position control
DF09895C4 Main beam headlight relay control circuit
DF10895C5 Front fog lights control circuit
DF10995C6 Rear fog lights control circuit
DF1339574 Deadlocking motor(s) circuit
DF13495D2 Hazard warning lights indicator light circuit
DF1359520 Rain detector
DF1369521 Light sensor
DF13796B1 UCH - Alternator connection
DF13896B2 Alternator
DF1399660 Interior lights
DF14096B3 Voltage regulator
DF21295B0 Alarm circuit
MR-413-X44-87B000$336.mif
UCH
Vdiag No.: 44

87B-26
MR-413-X44-87B000$384.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF011
PRESENT
OR
STOREDRAIN/LIGHT SENSOR CIRCUIT
1.DEF : Open circuit or short circuit
NOTESConditions for applying the fault finding procedure to stored faults:
Switch on the ignition, activate automatic headlighting by quickly performing the
following manipulation twice: control stalk (component code 209) on zero position →
control stalk (component code 209) in Side light position.
Status ET114 “Wiper request by rain sensor” should be “Low speed” or “High
speed” when the water runs over the rain/light sensor on the windscreen or
status ET115 “Request for lights to be switched on by light sensor” should be
“Present” by placing an opaque cover over the rain/light sensor.
Note:
If there is an open circuit on connection BPT, there is a malfunction on the
electric windows, rain/light sensor, interior light(s) and luggage compartment
light.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the function is not deactivated, quickly perform the following cycle twice to activate the automatic
headlighting function: Monolever (component code 209) OFF → Monolever (component code 209) in Side light
ON position.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that LC044 "Rain/light sensor" displays "Present". If not, carry out CF035 "Rain/light sensor".
Check that LC096 "Automatic wiper function" displays "With". If not, carry out CF194 "Automatic wiper
function".
Check that LC095 "Automatic headlight function", displays "With". If not, carry out CF193 "Automatic
headlight function".
Check the condition and the positioning of fuses F2 (15A), F8 (15A), F19 (5A), F27 (5 A) depending on the
equipment and F29 (15A) on the passenger compartment fuse and relay box (component code 1016).
Replace the fuse(s) or repair if necessary.
Check the condition and connection of the PE1, PE2 and PE3 connectors of the UCH (component code 645)
(tabs pushed back, oxidised, broken).
Check for + after ignition feed on connection AP43 of component 645.
Check for + accessories feed on connection SP2 (for vehicles fitted with a manual gearbox) or SP15
(for vehicles fitted with a sequential gearbox) of component 645.
Check for earth on connection NAM of component 645. Check the earth on connection MAM of component 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF011

87B-61
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF135
DF136
PRESENT
OR
STOREDRAIN DETECTOR
LIGHT SENSOR
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
Switching on the ignition, activating automatic headlight lighting by moving the control
stalk twice in quick succession as follows: control stalk (component code 209) to
position zero ΑΕ control stalk (component code 209) to side lights position.
Status ET114 "Wiper request from rain sensor" should be "Low speed" or "High
speed" when the water runs over the position of the rain/light sensor on the
windscreen or status ET115 "Request for lights to be switched on from light
sensor" should be "Present" when an opaque cover is placed over the rain/light
sensor.
Note:
If there is an open circuit on connection BPT, there will be a malfunction on the
electric window winders, on the rain/light sensor, on the interior lights and the boot
lighting.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the vehicle is configured with a rain/light sensor (component code 1415).
Check that LC044 Rain/light sensor is Present. If not, perform CF035 Rain/light sensor.
Check that LC096 Automatic wiper function displays With. If not, carry out CF194 "Automatic wiper
function".
Check that LC095 Automatic headlight function displays With. If not, carry out CF193 "Automatic headlight
function".
Check the condition and position of supply fuses F2 (15 A), F8 (15 A), F19 (5 A), F27 (5 A) according to the
equipment, F29 (15 A) of the rain/light sensor (component code 1415) on the passenger compartment fuse and
relay box (component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 3-track connector of the rain/light sensor (component 1415) (tabs
bent, broken or oxidised).
Check the condition and connection of the PE2 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF135 / UCH_V44_DF136

87B-65
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF139
PRESENT
OR
STOREDCOURTESY LIGHT
CC.1: Short circuit to + 12 volts
NOTESThe fault is declared present after:
Opening at least one door.
OR
Running AC063 Switching the interior lights on and off.
Check the correct operation of status ET463 Door(s) or tailgate.
Check the condition and connection of the 6-track connector of the front interior lighting (component code 213)
and connector PE1 of component 645 (tabs bent, oxidised, broken).
Check for + 12 V on connection BPT of component 213.
Check the continuity and insulation of the following connections:
●Connection code BTP, between components 213 and 645.
●Connection code 13E between components 213 and 645.
●Connection code MAM between component 213 and earth MAM.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the operation of the rabbet switches using ET463 Door(s) and tailgate.
If the supply, earths and connections are correct, replace the courtesy light (component code 213).
(See MR 411, Mechanical 81B, Interior lighting, courtesy light: Removal - Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF139

87B -143
MR-413-X44-87B000$624.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
ET463
CONTINUED 4
Check that the diode is fitted the right way
round (in accordance with the foolproofing
device).
Is the diode fitted the wrong way round?
Fit a diode the right way round in the correct
location in the passenger compartment fuse
box.
(see MR 411 Mechanical, 81C, Fuses,
Fuses: List and location of components)
A disconnected earth causes damage to
the fuse. If the diode and/or the fuse are
damaged, the tailgate earth (MYH) and the
passenger door earth (MAN and MAM)
should be checked.
If the earths are correct, replace the
diode and/or the fuse in the passenger
compartment fuse box (see MR 411
Mechanical, 81C, Fuses, Fuses: List and
location of components)Check the continuity of connection 86H between
components 1016 and 645.
If the connection or connections are faulty and there is
a repair procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the wiring is in order, replace the driver's door switch
(component code 140) (see MR 411 Mechanical
systems, 81B, Interior lights, Door switch:
Removal - Refitting)
A
YES
NO
B
DB
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.