Crankshaft pulley RENAULT TWINGO RS 2009 2.G Engine And Peripherals Owner's Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 652
Page 148 of 652

11A-31
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) .aSet up the engine support tool (Mot. 1379), shifting
the engine forwards.
aLift the engine slightly using the (Mot. 1379).
aRemove:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) .
aRefit the crankshaft accessories pulley bolt.
aUnclip the fuel pipe from the upper timing cover. Special tooling required
Mot. 1379Engine suppor t tool for cylin-
der head oper ations.
Mot. 1054TDC setting pin.
Tightening torquesm
tensioning roller nut24 N.m
lower timing cover bolt10 N.m
intermediate timing
cover bolts10 N.m
upper timing cover bolts37 N.m
10267
Page 151 of 652

11A-34
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aMake sure that the mark on the camshaft sprocket
and the mark on the crankshaft sprocket are aligned
with their fixed markings.
2 - Removing the timing belt
aRemove:
-the nut (4) from the tensioning roller,
-the tensioning roller,
-the timing belt (5) .
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: Timing belt,
parts always to be replaced: Timing belt tension-
ing roller,
parts always to be replaced: Crankshaft acces-
sories pulley bolts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the new tensioning roller, making sure:
-that the cylinder head ribbing is between the two
tensioning roller lugs,
-that the tensioning roller pin is properly positioned,
-that the tensioning roller is positioned as in the dia-
gram.
aDo not remove the pin from the new tensioning roller
before refitting the timing belt.
aScrew on the tensioning roller nut without tightening
it.
109738
109738
109761
Page 154 of 652

11A-37
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aCheck that the tensioning roller does not come into
contact with the cylinder head.
aIf the tensioning roller is in contact with the cylinder
head:
-set the engine to Top Dead Centre,
-remove the tensioning roller and the timing belt,
-insert the tensioning roller pin,
-repeat the timing belt refitting method from the be-
ginning, step by step.
III - FINAL OPERATION
aRefit:
-the lower timing cover,
-the lower timing cover bolt,
-the timing intermediate housing,
-the intermediate timing cover bolts,
-the upper timing cover,
-the upper timing cover.
aTorque tighten:
-the lower timing cover bolt (10 N.m),
-the intermediate timing cover bolts (10 N.m),
-the upper timing cover bolts (37 N.m)aFit the oil pressure sensor connector.
aClip the oil pressure sensor wiring on the upper tim-
ing cover.
aConnect the oil pressure sensor connector.
aFit the flexible heat shield on the oil pressure sensor
connector.
aClip the fuel pipe on to the upper timing cover.
aRefit:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) .
aRemove the tool (Mot. 1379).
aRefit:
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
109765
D4F, and 780 or 782
Page 155 of 652

11A-38
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).aRemove:
-the engine cover,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (80B, Headlights),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the camshaft position sensor (see 13B, Diesel in-
jection, Camshaft position sensor: Removal -
Refitting, page 13B-14) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) . Special tooling required
Mot. 1672Low er engine support.
Mot. 1489TDC locating pin.
Mot. 1430Set of 5 crankshaft and cam-
shaft pulley timing pins.
Tightening torquesm
tensioning roller bolt27 N.m
camshaft pulley wheel
bolts14 N.m
TDC setting pin plug25 N.m
cylinder head sus-
pended mounting bolts25 Nm
IMPORTANT
Wear protective gloves during the operation.
WARNING
The belt must be replaced with a new one if it has
been removed.
WARNING
When replacing the belt, always replace the tension
wheels and idler pulleys.
WARNING
Do not r un the engine without the accessories belt
to avoid damaging the crankshaft accessories pul-
ley.
Page 156 of 652

11A-39
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRefit the old crankshaft accessories pulley bolt (1)
fitted with a spacer (2) (which does not cover the tim-
ing sprocket mark).
aUnclip the upper timing cover at (3) .
aRemove the upper timing cover (4) .
aRaise the engine using the lower tool (Mot. 1672).
aUnclip the lower timing cover at (5) .
aLower the engine using the lower tool (Mot. 1672).
aRemove:
-the plastic clip (6) from the lower timing cover,
107272
K9K, and 740
19654
19654-1
Page 159 of 652

11A-42
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRemove the bolts (13) from the suspended mount-
ing on the cylinder head.
aTwist the timing belt slightly (to facilitate removing
the suspended mounting from the cylinder head).
aRemove the suspended mounting from the cylinder
head.aRemove the plug (14) from the TDC setting pin.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aTurn the crankshaft to position the camshaft pulley
hole (15) almost opposite the cylinder head hole (16)
.
136658
11299819650
107270
Page 160 of 652

11A-43
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aFit the tool (Mot. 1489) (17) on the cylinder block.
aTurn the crankshaft clockwise (timing end) smoothly
until the crankshaft is pressed against the TDC set-
ting pin.aInsert the (Mot. 1430) (18) in the camshaft pulley
and cylinder head holes.
aLoosen the timing tensioning roller bolt (19) to relax
the timing belt.
aRemove:
-the timing belt,
-the timing tensioning roller bolt,
-the timing tensioning roller.
19650-1
14489109049
109046
Page 165 of 652

11A-48
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
-the camshaft pulley timing pin (Mot. 1430).
aRotate the crankshaft twice clockwise (timing end)
before the camshaft pulley hole (28) is opposite the
cylinder head hole (29) .
aScrew tool (Mot. 1489) into the cylinder block.
aBring the crankshaft slowly and smoothly into con-
tact with the tool (Mot. 1489).
aSet the camshaft pulley using the (Mot. 1430).aIf the (Mot. 1430) does not fit in, loosen the camshaft
pulley wheel bolts by up to one turn.
aTurn the camshaft pulley hub using an offset span-
ner to set the camshaft pulley hub.
aDo not tighten the camshaft pulley wheel bolts.
107270
109049
109048
Page 168 of 652

11A-51
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRemove:
-the (Mot. 1489),
-the (Mot. 1430).
aRotate the crankshaft twice clockwise (timing end)
before the camshaft pulley hole is opposite the cylin-
der head hole.
aScrew tool (Mot. 1489) into the cylinder block.
aBring the crankshaft slowly and smoothly against the
TDC setting pin.
aSet the camshaft pulley using the (Mot. 1430).
aIf this is not possible, repeat the operation for refit-
ting the timing belt.
aRemove:
-the (Mot. 1489),
-the (Mot. 1430).
III - FINAL OPERATION
aRefit the TDC pin plug, coating the thread with SILI-
CONE ADHESIVE SEALANT (see Vehicle: Parts
and consumables for the repair) (04B, Consum-
ables - Products).
aTorque tighten the TDC setting pin plug (25 N.m).
aRefit the cylinder head suspended mounting .
aTorque tighten the cylinder head suspended
mounting bolts (25 Nm).aRefit the lower timing cover, positioning the tab (35)
in the opening (36) of the inner timing cover.
aRefit:
-the upper timing cover,
-the camshaft position sensor (see 13B, Diesel in-
jection, Camshaft position sensor: Removal -
Refitting, page 13B-14) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
109049
19659
Page 173 of 652

11A-56
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
aThe camshaft grooves (13) must be horizontal and
offset downwards.
aRemove the TDC setting pin (Mot. 1489).
aRemove:
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the upper timing cover bolts (14) ,
-the upper timing cover nuts (14) ,
-the upper timing cover (14) ,-the lower timing cover bolts (15) ,
-the lower timing cover (15) .
II - REMOVAL OPERATION
aThe crankshaft sprocket is cottered on this engine,
the timing setting and belt tensioning procedure re-
quire that the sprocket and dephaser be loosened
on the camshafts.
14490
14487