RENAULT TWINGO RS 2009 2.G Sequential Transmission Owners Manual

21B-91
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET053
VEHICLE SPEED SIGNAL DETECTION
STATUS
DEFINITIONThis status indicates detection by the sequential gearbox computer of the vehicle speed
and has the specification "DONE" or "NOT DONE".
NOTESNone
Engine stopped, ignition on
ET053: "DONE"
In the event of a fault, refer to the interpretation of the following faults:
●DF176 "Front right-hand wheel speed multiplex signal",
●DF175 "Front left-hand wheel speed multiplex signal",
●DF117 "Rear left-hand wheel speed multiplex signal",
●DF118 "Rear right-hand wheel speed multiplex signal".
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET053

21B-92
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET054
PUMP RELAY CONTROL
STATUS
DEFINITIONACTIVE: indicates that the pump is supplied to increase the pressure in the hydraulic
circuit.
INACTIVE: indicates that the pump is not being actuated.
NOTESNone
Engine running at idle speed
If parameter PR018 "Hydraulic pressure" is below 40 bar, ET054 is "ACTIVE" until PR018 = 50 bar is reached.
If parameter PR018 "Hydraulic pressure" is above 40 bar, ET054 is "INACTIVE".
In the event of a fault, refer to the interpretation of fault DF252 “Pump relay”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET054

21B-93
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET055
STARTER RELAY CONTROL
STATUS
DEFINITIONThis signal indicates the status of the starter control circuit and has the specification
"ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE
"ACTIVE" when the starter is operating.
In the event of a fault, perform fault finding on the UCH (see 87B, Passenger compartment connection unit).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET055

21B-94
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET056
CLUTCH SOLENOID VALVE CONTROL
STATUS
DEFINITIONThis signal indicates the status of the clutch solenoid valve and has the specification
"ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE: engine stopped
In the event of a fault, consult the interpretation of fault DF071 “Clutch solenoid valve circuit”.
Engine warm at idle speed
INACTIVE: engine running
ACTIVE: when a gear is being selected
In the event of a fault, consult the interpretation of fault DF071 “Clutch solenoid valve circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET056

21B-95
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET057
ENGAGEMENT SOLENOID VALVE 1 CONTROL
STATUS
DEFINITIONThis signal indicates the status of the control circuit of engagement solenoid valve 1 and
has the specification "ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE, engine stopped
In the event of a fault, consult the interpretation of fault DF072 “Engagement solenoid valve 1 circuit”.
Engine warm at idle speed
INACTIVE, engine running, vehicle stopped
ACTIVE when each gear is selected
In the event of a fault, consult the interpretation of fault DF072 “Engagement solenoid valve 1 circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET057

21B-96
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET058
ENGAGEMENT SOLENOID VALVE 2 CONTROL
STATUS
DEFINITIONThis signal indicates the status of the control circuit of engagement solenoid valve 2 and
has the specification "ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE, engine stopped
In the event of a fault, consult the interpretation of fault DF073 “Engagement solenoid valve 2 circuit”.
Engine warm at idle speed
INACTIVE, engine running, vehicle stopped
ACTIVE when each gear is selected
In the event of a fault, consult the interpretation of fault DF073 “Engagement solenoid valve 2 circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET056

21B-97
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET059
SELECTION SOLENOID VALVE 1 CONTROL
STATUS
DEFINITIONThis signal indicates the status of the control circuit of selection solenoid valve 1 and
has the specification "ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE, engine stopped
In the event of a fault, consult the interpretation of fault DF074 “Selection solenoid valve 1 circuit”.
Engine warm at idle speed
INACTIVE, engine running, vehicle stopped
ACTIVE during selection of first and second gears
In the event of a fault, consult the interpretation of fault DF074 “Selection solenoid valve 1 circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET059

21B-98
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET060
SELECTION SOLENOID VALVE 2 CONTROL
STATUS
DEFINITIONThis signal indicates the status of the control circuit of selection solenoid valve 2 and
has the specification "ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE, engine stopped
In the event of a fault, consult the interpretation of fault DF075 “Selection solenoid valve 2 circuit”.
Engine warm at idle speed
INACTIVE, engine running, vehicle stopped
ACTIVE during selection of fifth and reverse gears
In the event of a fault, consult the interpretation of fault DF075 “Selection solenoid valve 2 circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET060

21B-99
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET061
GEAR PROGRAMMING
STATUS
DEFINITIONThis signal indicates the status of the programming of all the gears and has the
specification "NOT DONE", "DONE" or "OK".
NOTESNone
Engine stopped, ignition on
ET061: "DONE" or "OK"
If "NOT DONE", consult the interpretation of faults DF069 "Selecting position sensor circuit", DF070
"Engaging position sensor circuit" and DF067 "Lever position sensor circuit".
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET061

21B -100
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET062
BITING POINT PROGRAMMING
STATUS
DEFINITIONThis signal indicates the status of the programming of the clutch biting point and has the
specification "NOT DONE" or "DONE".
NOTESNone
Engine stopped, ignition on
ET062: DONE
If "NOT DONE", put the gearbox in neutral.
Start the engine.
Wait 10 seconds without changing gear (to program the clutch biting point).
Check the programming was applied correctly:
ET062 displays "DONE".
If "NOT DONE", refer to the interpretation of fault DF068 "Clutch position sensor circuit".
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET062