washer fluid SAAB 9-3 2009 User Guide

217
Car care
Washers
The reservoir capacity is approx. 6 qts.
(5.8 liters).
When the washer fluid level drops below
1 quart (1 liter), the headlight washers (if
equipped) are deactivated. This is in order
to prioritize the windshield. The following
message is displayed on the SID:
Headlight washers are only available on
certain markets.
Fill with a mixture of washer fluid and water
as recommended by the table on
the packaging to reduce the risk of freezing
and to ensure effective cleaning (see also
page 104).
Washer jetsThe washer jets, which are adjustable, can
be cleaned with a pin if necessary.
WARNING
Take care not to spill washer fluid concen-
trate onto hot surfaces. Washer fluid con-
centrate can contain flammable ingredi-
ents such as alcohol.
Washer fluid level low.
Refill.
Washer fluid reservoir93_US_7carcare_MY09.fm Page 217 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

220 Car careLow beam, halogenLeft-hand side1 Lift aside the hose 3 running along the side of the battery cover.
2 Release the two retainers (a quarter of a turn counterclockwise) in the leading edge of the cover and remove the cover.
3 Pull up the washer fluid filler pipe.
4 Remove the air pipe from the front edge of the battery box.
5 Pull up the fuse panel 3 in front of the battery, see page 239.
Both sides 1 Remove the cover from t he rear of the headlight.
2 Twist the bulb holder counterclockwise and withdraw the holder from the reflector. 3 Change the bulb without touching the glass with your fingers.
Insert the bulb holder into the reflector and twist it clockwise until
it locks.
4 Refit the cover over th e rear of the headlight.
Left-hand side 5 Refit the air pipe to th e front of the battery box.
6 Refit the washer fluid filler pipe.
7 Refit the battery cover.
8 Refit the hose 3 running along the side of the battery cover.
NOTICEDo not fit bulbs with a higher rating than 55 W as this could
damage the headlight reflector. Furthermore, the car’s wiring is
not designed to cope with higher wattages.
Retainers on the battery cover Changing the low beam bulb93_US_7carcare_MY09.fm Page 220 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

221
Car care
High beam, halogenLeft-hand side
1 Lift aside the hose 3 running along the side of the battery cover.
2 Release the two retainers (a quarter of a turn counterclockwise) in the leading edge of the cover and remove the cover.
3 Pull up the washer fluid filler pipe.
4 Remove the air pipe from the front edge of the battery box.
5 Pull up the fuse panel 3 in front of the battery, see page 239.
Both sides 1 Remove the cover from t he rear of the headlight.
2 Twist the bulb holder counterclockwise and withdraw the holder from the reflector.
3 Change the bulb without touching the glass with your fingers. Insert the bulb holder into the reflector and twist it clockwise until
it locks. 4 Refit the cover over th
e rear of the headlight.
Left-hand side 5 Refit the air pipe to th e front of the battery box.
6 Refit the washer fluid filler pipe.
7 Refit the battery cover.
8 Refit the hose 3 running along the side of the battery cover.
NOTICEDo not fit bulbs with a higher rating than 55 W as this could
damage the headlight reflector. Furthermore, the car’s wiring is
not designed to cope with higher wattages.
Retainers on the battery cover Changing the high beam bulb93_US_7carcare_MY09.fm Page 221 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

222 Car careDaytime Running LightLeft-hand side1 Lift aside the hose 3 running along the side of the battery cover.
2 Release the two retainers (a quarter of a turn counterclockwise) in the leading edge of the cover and remove the cover.
3 Pull up the washer fluid filler pipe.
4 Remove the air pipe from the front edge of the battery box.
5 Pull up the fuse panel 3 in front of the battery, see page 239.
Both sides 1 Remove the cover from t he rear of the headlight.
2 Twist the bulb holder counterclockwise and withdraw the holder from the reflector.
3 Change the bulb without touching the glass with your fingers. Insert the bulb holder into the reflector and twist it clockwise until it locks. To facilitate fitting, look in through the headlight lens
when fitting the bulb. Check that the new bulb is firmly seated.
4 Refit the cover over th e rear of the headlight.
Left-hand side 5 Refit the air pipe to th e front of the battery box.
6 Refit the washer fluid filler pipe.
7 Refit the battery cover.
8 Refit the hose 3 running along the side of the battery cover.Retainers on the battery cover93_US_7carcare_MY09.fm Page 222 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

223
Car care
Front turn signal bulbsLeft-hand side
1 Lift aside the hose 3 running along the
side of the battery cover.
2 Release the two retainers on the battery cover and remove the cover.
3 Pull up the washer fluid filler pipe.
4 Remove the air pipe from the front edge of the battery box.
Both sides 1 The bulb holder has a bayonet fitting. Turn the bulb holder counterclockwise
and withdraw it.
2 Hold the bulb holder with a firm grip. Use a screwdriver to pry the bulb from the
holder. 3 Fit the new bulb.
4 To facilitate fitting, look in through the
headlight lens when fitting the bulb.
Check that the new bulb is firmly seated.
Left-hand side 5 Refit the air pipe to the front edge of the battery box.
6 Refit the washer fluid filler pipe.
7 Refit the battery cover and hose 3.
Side-mounted turn signal bulbs1 Slide the lamp fitting forward so that its
rear end can be pulled out.
2 Turn the bulb holder counterclockwise and withdraw it from the lamp fitting.
Change the bulb.
3 To fit, engage the two catches on the rear edge of the lamp fitting with the
edge of the opening. Then press in the
front edge of the lamp fitting so that the
groove in the spring engages the plastic
edge.
Change of front turn signal bulb
93_US_7carcare_MY09.fm Page 223 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

238 Car careFuse panel in engine bayNo. Amp. Function1--
2 10 Engine control module; au
tomatic transmission con-
trol module 3
320Horn
4 10 Engine control module; ba ttery disconnect switch3
5--
6 10 Selector lever, automatic transmission
3; clutch pedal
switch
7 10 Xenon Cornering Headlights, left 3
8 5 Relay for vacuum pump (brake system) 3
9--
10 - -
11 - -
12 10 Washer fluid pump, rear window 3
13 - -
14 - -
15 30 Washer fluid pump, headlights3
16 30 Front right parking light; fr
ont right turn signal; left and
right side turn signal; right high beam; left low beam;
front left fog light 3
17 30 Windshield wiper motor, low speed
18 30 Windshield wiper motor, high speed
19 20 Parking heater; auxiliary heater 3
20 10 Headlight levelling
3 xenon cornering headlights,
right 3
21 - -
22 30 Washer fluid pump, windshield
23 - -
24 20 Flash-to-pass; high beam, right and left (cars with
Daytime Running Lights only)
25 20 Amplifier, sound system II 3
26 30 Front left turn signal; front left parking light; front right
fog light 3; right low beam; left high beam
27
–37 MAXI
93_US_7carcare_MY09.fm
Page 238 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

239
Car care
Fuse panel in front of battery 3
Relays
R 1 Washer fluid pump, windshield
R2 -
R3 -
R4 -
R 5 Flash-to-pass
R6 Horn
R7 -
R8 Starter motor
R 9 Windshield wipers ON/OFF
R10 Washer fluid pump, rear window 3
R11 Ignition +15
R12 Windshield wipers, high/low speed
R13 -
R14 Washer fluid pump, headlights 3
R15 -
R16 -
No. Amp. Function 1 - Air pump, secondary air 3
2 20 Fuel pump; preheated oxygen sensors (lambda
probe)
3 10 A/C compressor
430Main relay
Relays 1-
2 A/C-compressor
3 Preheated oxygen sensors (lambda probe)
4 Main relay, engine (ECM/EVAP/injectors)
93_US_7carcare_MY09.fm Page 239 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

268 Car careThe underside of the car also needs wash-
ing regularly, and this should be done extra
thoroughly at the end of winter. Clean the
underside of the car by hand if the car is
usually washed in an automatic car wash
without special facilities for underbody
cleaning.
Never wash or leave the car to dry in the
sun, but wipe it dry with a chamois leather
immediately after washing to avoid smears
and streaks.
Clean the inside of window glass using a
proprietary window cleaner. This is particu-
larly important when the car is new, as
upholstery and trim have a tendency to
sweat a little at first.
Keep the glass well polished, as this helps
to prevent misting.
Clean the outside of the windows with Saab
washer fluid. This is especially important if
the car has been washed in an automatic
car wash, as sometimes a wax treatment is
used that can contaminate the windshield
and impair the performance of the wipers.
Saab offers a full co mplement of car care
products. See your dealer or visit us at our
website. Convertible
 If a pressure washer is used be heedful of
the following recommendations:
 On the lower part of the car (not higher than the door handles): max pressure
of 100 bar and not closer than 8 in.
(20 cm).
 On the upper part of the car: tax pres- sure of 100 bar and not closer than
32 in. (80 cm).
 Do not use any drying chemicals or water- proofing agents.
 Avoid automatic car washes.
WARNING
 Read and follow the instructions on the packaging of the recommended
cleaning agents and waterproofing
agents. We recommend that you con-
tact an authorized Saab dealer
regarding recommended cleaning
agents and waterproofing agents.
 Never treat the soft top with hot wax or similar.
 Never use petrochemical based sol-
vents for cleaning. Only use water with
a recommended cleaning agent. Pet-
rochemical based solvents can cause
irreparable damage to the soft top.
 Never use a pressure washer to clean the soft top. Only use normal house-
hold water pressure.NOTICE Only operate the soft top when it is clean and dry.
 Do not lower the so ft top when it is
damp. This can cause folds and pres-
sure marks. If the soft top is heavily
soiled, the dirt may cause irreparable
visible chafe marks.
 Only use water, recommended clean- ing agents and a microfibre cloth if the
soft top is already damaged, other-
wise the damage can become worse.
 At creases, seams and window edges the cleaning motion should be away
from the crease, seam or window
edge in to the soft top.
93_US_7carcare_MY09.fm Page 268 Tuesday, April 15, 2008 11:26 AM
ProCarManuals.com

285 Technical data
Curb weight
(i.e. with full fuel tank, full washer fluid res-
ervoir, standard tools and spare wheel):
SportSedan_______________________ 3220–3880 lbs.
(1460–1760 kg)
Convertible _______________________ 3520–3870 lbs.
(1595–1755 kg)
SportCombi_______________________ 3310–4010 lbs.
(1500–1820 kg)
Gross vehicle weight (GVW):
SportSedan_______________________ 4160–4820 lbs.
(1885–2185 kg)
Convertible _______________________ 4420–4650 lbs.
(2005–2110 kg)
SportCombi_______________________ 4240–4950 lbs.
(1925–2245 kg)
Maximum axle load, front wheel drive:
SportSedan, front __________________ 2540 lbs. (1150 kg)
SportSedan, rear __________________ 2230 lbs. (1010 kg)
Convertible, front __________________ 2560 lbs. (1160 kg)
Convertible, rear ___________________ 2310 lbs. (1050 kg)
SportCombi, front __________________ 2340 lbs. (1150 kg)
SportCombi, rear __________________ 2430 lbs. (1100 kg)
Maximum axle load, all-wheel-drive models:
SportSedan, front __________________ 2600 lbs. (1180 kg)
SportSedan, rear __________________ 2380 lbs. (1080 kg)
SportCombi, front __________________ 2600 lbs. (1180 kg)
SportCombi, rear __________________ 2520 lbs. (1140 kg)Weight distribution:
Curb weight + driver (150 lbs. (68 kg)),
front/rear, SportSedan and SportCombi_ approx. 60/40 %
GVW, front/rear, SportSedan and
SportCombi ______________________ approx. 50/50 %
Maximum roof load, SportSedan and
SportCombi ______________________ 220 lbs. (100 kg)
Maximum load in trunk, SportSedan,
Convertible and SportCombi _________ 175 lbs. (80 kg)
The combined weight of occupants and
cargo should never exceed:
SportSedan and SportCombi _________ 926 lbs. (420 kg)
Convertible _______________________ 776 lbs. (352 kg)
Maximum combined weight of driver and
passengers ______________________
SportSedan and SportCombi (5x150 lbs.) 750 lbs. (340 kg)
Convertible (4x150 lbs.) _____________ 600 lbs. (272 kg)93_US_MY09.book Page 285 Tuesday, April 15, 2008 10:30 AM
ProCarManuals.com

294 Technical dataWarning and indications that can
be shown on the SIDWhich warnings and indications that can be
shown depends on engine variant and car
specification.
The warnings/indications that contain an
exclamation mark are shown together with
a warning or check light in the main instru-
ment panel.
Symbol Text
Antilock brake malfunc.
Contact service.
Brake malfunction.
Make a safe stop.
Brake fluid level low.
Make a safe stop.
Release park brake.
Oil pressure low.
Make a safe stop.
Low engine oil level.
Fill oil now.
Reduced engine power.
Contact service.
Tighten fuel filler cap.
Limited performance.
Coolant level low.
Refill.
Hot engine. Make a
safe stop. Idle engine.
Airbag malfunction.
Contact service.
Gearbox too hot. Make a
safe stop. Open hood.
Battery not charging.
Make a safe stop.
Headlight levelling
malfunction.
Cornering headlights
malfunction
Tap brakes lightly
before using cruise ctrl.
Traction control failure.
Contact service.
Stability control failure.
Contact service.
Turn on the lights.
Washer fluid level low.
Refill.
Rain sensor malfunc.
Contact service.
Key not accepted.
Contact service.
Remote control battery
low. Replace battery.
Number of keys:
Active key number:
Steering lock malfunc.
Make a safe stop.
Pull out key, turn
steering wheel. Restart.
Theft protection failure.
Contact service.
Alarm tripped during
last arming period.
93_US_MY09.book Page 294 Tuesday, April 15, 2008 10:30 AM
ProCarManuals.com