light SATURN RELAY 2007 Service Manual

Reducing Speed While Using Cruise
Control
There are two ways to reduce the vehicle’s speed
while using cruise control:
Push the cruise control lever downward
toward the minus (set/coast/decelerate)
position until a lower speed is reached, then
release it.
To slow down in very small amounts, push the
cruise control lever downward toward the
minus (set/coast/decelerate) position briey.
Each time this is done, the vehicle will
slow down approximately one mph (1.6 km/h).
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase the vehicle’s
speed. When you take your foot off the pedal,
the vehicle will slow down to the cruise control
speed set earlier.
Using Cruise Control on Hills
How well the cruise control will work on hills
depends upon the vehicle’s speed, its load, and
the steepness of the hills. When going up
steep hills, the accelerator pedal might have to be
used in order to maintain the vehicle’s speed.
When going downhill, the brakes might have to be
applied, or the transaxle might have to be
shifted to a lower gear to keep the vehicle’s speed
down. Doing either of these things will take the
vehicle out of cruise. It may be better not to
use the cruise control if the brakes constantly have
to be applied, or the vehicle continuously needs
to be shifted to a lower gear.
Cancelling Cruise Control
To cancel a cruise control session, pull the cruise
control lever forward, or step lightly on the
brake pedal.
Doing either of these things will only end the
current cruise control session, but the set speed
will be retained in memory.
Push the button at the end of the cruise control
lever to turn the system off.
191
ProCarManuals.com

Erasing Speed Memory
When the cruise control or the ignition is turned
off, the cruise control set speed memory is erased.
Exterior Lamps
The control to the left of
the steering column
operates the exterior
lamps.
9(Off):Turn the control to this position to
toggle off all lamps. This is a momentary control
that will spring back to AUTO when released.
This momentary control will turn the automatic
headlamps and/or the Daytime Running Lamps on
and off for U.S. vehicles. For vehicles rst sold
in Canada, this is only true when the transaxle is in
PARK (P).AUTO (Automatic):Turn the control to this
position to set your headlamps in automatic mode.
AUTO mode, if enabled, will turn the exterior
lamps on and off automatically depending on how
much light is available outside the vehicle.
Due to the momentary switch design, your
automatic lights may be disabled even if the
control is in the AUTO position.
;(Parking Lamps):Turn the control to this
position to turn on the parking lamps together with
the following:
Taillamps
Instrument Panel Lights
5(Headlamps):Turn the control to this position
to turn on the headlamps, together with the
previously listed lamps and lights.
192
ProCarManuals.com

Wiper Activated Headlamps
This feature, if equipped, will automatically
activate the headlamps and parking lamps after
the windshield wipers have been in use for
about 30 seconds and when all of the following
conditions are met.
The exterior lamp control is in AUTO.
The headlamps have not already been
activated by automatic lighting.
The automatic lighting feature has not been
disabled using the exterior lamp control.
SeeExterior Lamps on page 192for additional
information.
If the wipers are activated for over 30 seconds
and the exterior lamp control is in the parking
lamps position, or the automatic lighting feature
has been disabled using the exterior lamp control,
a HEADLAMPS SUGGESTED message will
appear on the Driver Information Center, if
equipped.
Headlamps on Reminder
If you turn the ignition to LOCK while leaving the
lamps on, you will hear a warning chime once
the driver’s door is opened.
Daytime Running Lamps (DRL)/
Automatic Headlamp System
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional Daytime Running Lamps
are required on all vehicles rst sold in Canada.
193
ProCarManuals.com

A light sensor on top of the instrument panel
makes the DRL work, so be sure it is not covered.
The DRL system will make front parking and
turn signal lamps come on in daylight when the
following conditions are met:
The ignition is on.
The exterior lamps control is off.
When the DRL are on, only your front turn signal
lamps will be on. Your instrument panel will
not be lit up.
When it is dark enough outside, the exterior lamps
will come on automatically. When it is bright
enough outside, the exterior lamps will turn off and
the DRL will turn on. Of course, you may still
turn on the headlamps any time you need to.If you start your vehicle in a dark garage, the
automatic headlamp system will come on
immediately. Once you leave the garage, it will
take approximately 30 seconds for the automatic
headlamp system to change to DRL if it is
light outside. During that delay, your instrument
panel cluster may not be as bright as usual. Make
sure your instrument panel brightness control is
in the full bright position. SeeInstrument
Panel Brightness on page 195.
To idle your vehicle with the DRL and automatic
headlamps off, toggle the exterior lamp control
to off after starting the vehicle.
As with any vehicle, you should turn on the
regular headlamp system when you need it.
194
ProCarManuals.com

Instrument Panel Brightness
The knob to adjust the
instrument panel
brightness is located in
the center of the
interior lamp controls.
Turn the knob clockwise to brighten the lights and
counterclockwise to dim them.
Interior Lamps Control
The interior lamp control
is located to the right of
the exterior lamp
controls on the
instrument panel to the
left of the steering
column.
R(Interior Lamp Override):Turn the outer
knob to this position to have your interior lamps
remain off while any door is open.
1(Door):Turn the outer knob to this position to
turn the interior lamps on while any door is
open and when the ignition key is removed from
the ignition.
+(Interior Lamps):Turn the outer knob to
this position to turn the interior lamps on.
Turn the inner knob to adjust the instrument panel
brightness, described earlier in this section.
195
ProCarManuals.com

Dome Lamp
The dome lamp is located in the headliner and has
two buttons to manually turn it on or off. The dome
lamp will come on each time you open a door,
unless you turn on the interior lamps override
feature. SeeInterior Lamps Control on page 195.
Entry Lighting
With entry lighting, the interior of your vehicle is
illuminated so that you can see inside before
you enter your vehicle. The lamps will come on for
20 seconds if you unlock your door using your
key or the remote keyless entry transmitter and the
ignition is in LOCK. After 20 seconds have
passed, the interior lamps will slowly fade out. The
lamps will turn off before the 20 seconds if you
do one of the following:
Lock all the doors using the key.
Press lock on the power door lock switch.
Press lock on the remote keyless entry
transmitter.
When any door is opened, entry lighting is
cancelled. The interior lamps will stay on while
any door or the liftgate is open, and slowly fade out
when all doors and the liftgate are closed.The interior lamps may stay on for up to 25 seconds
after all doors have been closed if they have not
been locked. SeeDelayed Lighting on page 196.
To turn the entry lighting feature off or on, see
DIC Vehicle Personalization (Uplevel Only)
on page 261.
Delayed Lighting
The delayed lighting feature will continue to
illuminate the interior for 20 seconds after all doors
have been closed, so that you can nd your
ignition and buckle your safety belt at night.
Delayed lighting will not occur while the ignition is
in RUN or ACCESSORY. After 20 seconds
have passed, the interior lamps will slowly fade
out. The lamps will fade out before the 20 seconds
have passed if you do one of the following:
Turn the ignition to RUN or ACCESSORY.
Lock all doors using the remote keyless entry
transmitter.
Lock all doors using the power door lock
switch or the key.
To turn the delayed lighting feature off or on, see
DIC Vehicle Personalization (Uplevel Only) on
page 261.
196
ProCarManuals.com

Exit Lighting
With exit lighting, the interior lamps will come on
for about 25 seconds whenever you remove
the key from the ignition. If you turn the ignition
key to RUN or ACCESSORY, the lamps will fade
out. The lamps will also fade out if you lock the
doors with the power door lock switch or the
remote keyless entry transmitter.
When any door is opened, exit lighting is
cancelled. The interior lamps will stay on while
any door or the liftgate is open, and slowly fade out
when all doors and the liftgate are closed.
The interior lamps may stay on for up to
20 seconds after all doors have been closed if
they have not been locked. SeeDelayed Lighting
on page 196.
To turn the exit lighting feature off or on, seeDIC
Vehicle Personalization (Uplevel Only) on
page 261.
Front Reading Lamps
There are two reading lamps and one courtesy
lamp in the overhead console. To turn either
reading lamp on or off, press the lens of the lamp.
The courtesy lamp will come on each time you
open a door, unless you turn on the interior lamps
override feature. SeeInterior Lamps Control on
page 195.
Rear Reading Lamps
There are two reading lamps in the third row
headliner. To turn either reading lamp on or off,
press the lens of the lamp.
There may also be a reading lamp in the second
row, integrated with the dome lamp. To turn
the second row reading lamp on or off, press the
button next to the lamp lens.
197
ProCarManuals.com

Cargo Lamp
The cargo lamp is located in the rear of your
vehicle, above the liftgate opening, and does not
have a switch. The cargo lamp will come on
each time you open a door, unless you turn on the
interior lamps override. SeeInterior Lamps
Control on page 195.
Electric Power Management
This vehicle has Electric Power Management
(EPM), an advanced control system. It estimates
the battery’s temperature and state of charge
and then adjusts the voltage for best performance
and extended life of the battery.When the battery’s state of charge is low, the
voltage is raised slightly to quickly put the charge
back in. When the state of charge is high, the
voltage is lowered slightly to prevent overcharging.
If the vehicle has a voltmeter gage, you may
see the voltage move up or down. This is normal.
If there is a problem, an alert will be displayed.
The battery can be discharged at idle if the
electrical loads are very high. This is true for all
vehicles. This is because the generator (alternator)
may not be spinning fast enough at idle to
produce all the power that is needed for very high
electrical loads.
A high electrical load occurs when several of the
following loads are on: headlamps, high beams,
fog lamps, rear window defogger, climate
control fan at high speed, heated seats, engine
cooling fans, trailer loads, and loads plugged into
accessory power outlets.
198
ProCarManuals.com

Overhead Console Switchbank
The overhead console switchbank is located in the
overhead console. This switchbank may include
the following:
Power Sliding Door(s)/Override Switch(es).
SeePower Sliding Door (PSD) on page 121.
Power Rear Quarter Windows. SeePower
Rear Quarter Windows on page 132.
Ultrasonic Rear Parking Assist (URPA)
Disable Switch. SeeUltrasonic Rear Parking
Assist (URPA) on page 200.
If your vehicle does not have some of these
options, there will be a blank.
Ultrasonic Rear Parking
Assist (URPA)
If your vehicle is equipped with the Ultrasonic
Rear Parking Assist (URPA) system, it is designed
to help you park, while the vehicle is in
REVERSE (R). It operates only at very low
speeds, less than 3 mph (5 km/h). URPA can help
make parking easier and to help you avoid
colliding with objects such as parked vehicles. The
URPA system can detect objects up to 5 feet
(1.5 m) behind the vehicle, and tell you how close
these objects are from your rear bumper.
Your vehicle’s URPA operates when the shift lever
is moved into REVERSE (R) and the vehicle
speed is less than 3 mph (5 km/h). Four ultrasonic
sensors located at the rear bumper are used to
detect the distance to the object. The URPA
display is located inside the vehicle, near the rear
window. It has three color-coded lights used to
provide distance and system information to
the driver.
200
ProCarManuals.com

{CAUTION:
The Ultrasonic Rear Park Assist (URPA)
system does not replace driver vision.
URPA does not:
Operate above speeds of 3 mph
(5 km/h).
Detect objects more than 5 feet
(1.5 meters) behind the vehicle. This
distance may be less during warmer
or humid weather.
Detect objects that are below the
bumper, underneath the vehicle, or
that are very close to the vehicle.
Detect children, pedestrians,
bicyclists, or pets.
So if you do not use proper care before
backing up, you could hit a vehicle, child,
pedestrian, bicyclist, or pet, resulting in
vehicle damage, injury, or death. Even
though the vehicle has the URPA system,
always check carefully before backing up
by checking behind your vehicle.URPA can be turned off
by pressing the rear
park aid disable switch
located in the
overhead console
switchbank.
While the system is disabled, an indicator light will
be lit on the switch. You will not see any lights
on the rear display if the switch is in the off
position.
201
ProCarManuals.com