engine oil Seat Alhambra 2006 Owner's Guide

Checking and refilling levels213
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
Oil properties
Viscosity
The viscosity class of the oil is selected according to the diagram.
When the ambient temperature falls outside the limits of the scale for a short
period, an oil change is not required.
Mono-grade oil
Single grade oils are generally not suitable for all year round use, due to
ranges of viscosity
43).These oils are only useful in a climate that is constantly very cold or very
warm.
Engine oil additives
No type of additive should be mixed with the engine oil. The deterioration
caused by these additives is not covered by the warranty.
Fig. 141 Types of oil
according to temperature
Engine typeSpecification
PetrolVW 501 01/ VW 502 00/ VW 504 00
DieselVW 505 00/ VW 505 01/ VW 507 00/ VW 506 01
Diesel Injector Pump
a)
a)Only use recommended oils, otherwise you may damage the engine.
VW 505 01/ VW 507 00/ VW 506 01
Diesel Injector Pump Motor 118 kW
a)VW 506 01/ VW 507 00
Diesel Engines with Particulate filter (DPF)
a)VW 507 00
43)Viscosity: Ability to flow

Checking and refilling levels 214
Note
Before a long trip, we recommend finding an engine oil that conforms to the
corresponding VW specifications and keeping it in the vehicle. This way, the
correct engine oil will always be available for a top-up if needed.
Checking the engine oil level
The engine oil dipstick indicates the level of the oil.
Before opening the bonnet, read and observe the warnings
Ÿpage 209.
– Park the vehicle on an even surface.
– Stop the engine and wait a few minutes for the oil to drain back
into the sump.
– Raise the bonnet Ÿpage 211.– Pull out the dipstick.
– Wipe the dipstick with a cloth and insert it again, pushing it in as
far as it will go.
– Then pull the dipstick out again and check the oil level .
– Replace the dipstick, pushing it in as far as it will go.
If the oil level is in area Ÿfig. 142 , you must not top up with oil.
If the oil level is in area , you may top up with oil (approx. 0,5 l).
If the oil level is in area , you must top up with oil (approx. 1,0 l).
It is normal for the engine to consume a certain amount of oil. Consumption
can be up to 1.0 litres per 1,000 km. For this reason the engine oil level must
be checked at regular intervals, preferably when filling the tank and before a
journey.
When the engine is working hard, for instance during sustained high-speed
motorway cruising in summer, when towing a trailer or climbing on mountain
passes, the oil level should preferably be kept within area (but not above).
WARNING
Special care must be taken when working on the engine or on components
in the engine compartment.
•When working in the engine compartment, always observe the safety
warnings Ÿpage 209
Caution
If the oil level is above the area do not start the engine. This could result
in damage to the engine and catalytic converter. Contact SEAT Service Centre ®.
Fig. 142 Dipstick
AA
AB
AC
AA
AA

Checking and refilling levels215
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
Topping up engine oil E
Top up gradually with small quantities of oil.
Before opening the bonnet, read and observe the warnings Ÿ in
“Safety instructions on working in the engine compartment” on
page 209 .
– Unscrew cap from oil filler opening Ÿfig. 143.
– Top-up oil in small amounts, using the correct oil.
– To avoid over-filling with engine oil, you should top-up using
small quantities, wait a while and check the oil level before
adding any more oil.
– As soon as the oil level is in area , carefully close the cap.
The position of the oil filler opening is shown in the corresponding engine
compartment diagram Ÿpage 262.Engine oil specification Ÿpage 212.
WARNING
Oil is highly inflammable! Ensure that no oil comes into contact with hot
engine components when topping up.
Caution
If the oil level is above the area do not start the engine. This could result
in damage to the engine and catalytic converter. Contact a qualified work-
shop.
For the sake of the environment
The oil level must never be above area . Otherwise oil can be drawn in
through the crankcase breather and escape into the atmosphere via the
exhaust system.
Changing engine oil
The engine oil must be changed at the intervals given in the
service schedule.
We recommend that you have the engine oil changed by an Authorised
Service Centre.
The two different oil change intervals are shown in the Inspection and Main-
tenance Plan.
WARNING
Only change the oil yourself if you have the specialist knowledge required!
Fig. 143 In the engine
compartment: Engine oil
filler cap
AB
AA
AA

Checking and refilling levels 216
•Before opening the bonnet, read and observe the warnings
Ÿpage 209, “Safety instructions on working in the engine compartment”
.
•Wait for the engine to cool down. Hot oil may cause burn injuries.
•Wear eye protection to avoid injuries caused by splashes of oil.
•When removing the oil drain plug with your fingers, keep your arm hori-
zontal to help prevent oil from running down your arm.
•Wash your skin thoroughly if it comes into contact with engine oil.
•Engine oil is poisonous! Used oil must be stored in a safe place out of
the reach of children until it is disposed of.
Caution
No additives should be used with engine oil. This could result in engine
damage. Any damage caused by the use of such additives would not be
covered by the factory warranty.
For the sake of the environment
•Because of the disposal problems, the necessary special tools and
specialist knowledge required, we recommend that you have the engine oil
and filter changed by an Authorised Service Centre.
•Never pour oil down drains or into the ground.
•Use a suitable container when draining the used oil. It has to be large
enough to hold all the engine oil
Coolant
Coolant specifications
Coolant is a mixture of water and at least 40% coolant addi-
tive.
The cooling system must be filled with a mixture of water and at least 40 % of
our coolant additive G 12+ or an additive with the specification TT-VW 774 F
(it is dyed purple). This mixture gives the necessary frost protection down to
-25°C and protects the alloy parts of the cooling system against corrosion. It
also prevents scaling and raises the boiling point of the coolant.
The concentration of coolant must always be at least 40% - even if frost
protection is not required.
If greater frost protection is required in very cold climates, the proportion of
the antifreeze additive G 12+ can be increased. However, the percentage of
coolant additives should not exceed 60%, as this would reduce the frost
protection. It would also reduce the cooling effect. A mixture with 60%
coolant additive will give frost protection to approx. -40°C.
WARNING
•The coolant additive is toxic. There is a toxic risk. Always keep the
coolant additive in the original container that should be stored out of the
reach of children. The same applies to coolant that you have drained off.
•The coolant additive G 12+ must be added in sufficient quantities to
provide anti-freeze protection at the coldest ambient temperatures that
can be expected. At extremely cold ambient temperatures, the coolant
could freeze, causing the vehicle to breakdown. As the heater would also
not work in this situation, there is a risk of suffering exposure!
WARNING (continued)

Checking and refilling levels219
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
WARNING
Any work carried out in the engine compartment or on the engine must be
carried out cautiously.
•When working in the engine compartment, always observe the safety
warnings Ÿpage 209
Caution
•Never put radiator anti-freeze or other additives into the windscreen
washer fluid.
•Always use approved windscreen cleansing products diluted as per
instructions. If you use other washer fluids or soap solutions, the tiny holes
in the fan-shaped nozzles could become blocked.
Changing the front windscreen wiper blades
Damaged wiper blades should be replaced immediately.
Check the condition of the wiper blades regularly. Change them as
required.
Change the windscreen wiper blades
– Lift the wiper arm away from the glass. Do not pull the arm by the
blade.
– Turn the wiper blade as shown by arrow Ÿfig. 146 as far as
it will go and then pull it off as shown by arrow Ÿfig. 147 .
– Push a new wiper blade of the same length and version onto the
wiper arm and turn the wiper blade to the stop against the direc-
tion shown by arrow .
– Place the wiper arm in the starting position.
These are available from SEAT Service®.
If the windscreen wipers scrape, they should be replaced if they are
damaged, or cleaned if they are soiled.
Fig. 146 Windscreen
wipers raised
Fig. 147 Removing front
wipers
A1
A2
A1

Checking and refilling levels221
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
– Insert a new wiper blade of the same length and design in the
direction of arrow and hook the blade back onto the wiper
arm.
– Now pull the wiper blade against the direction of arrow until
it engages.
– Push the wiper arm back against the glass.
These are available from SEAT Service®.
If the windscreen wiper scrapes, they should be replaced if they are
damaged, or cleaned if they are soiled.
If this does not produce the desired results, the setting angle of the wind-
screen wiper arms might be incorrect. They should be checked by a qualified
workshop and corrected if necessary.
WARNING
Do not drive unless you have good visibility through all windows!
•Clean the windscreen wiper blades and all windows regularly.
•The wiper blades should be changed once or twice a year.
Caution
•Damaged or dirty windscreen wipers could scratch the windscreen.
•Never use fuel, nail varnish remover, paint thinner or similar products to
clean the windows. This could damage the windscreen wiper blades.
•Never move the windscreen wiper or windscreen wiper arm manually - this
could cause damage!
Note
•The wiper arms can be moved to the service position only when the
bonnet is properly closed.
Brake fluid
Checking the brake fluid level
The brake fluid is checked at the intervals given in the service
schedule.
– Read off the fluid level at the transparent brake fluid reservoir. It
should always be between the “MIN” and “MAX” marks.
A2
A2
Fig. 149 In the engine
compartment: Brake fluid
reservoir cover

Checking and refilling levels 222
The position of the brake fluid reservoir is shown in the corresponding engine
compartment diagram Ÿpage 262. The brake fluid reservoir has a black and
yellow cap.
The brake fluid level drops slightly when the vehicle is being used as the
brake pads are automatically adjusted as they wear.
However, if the level goes down noticeably in a short time, or drops below the
“MIN” mark, there may be a leak in the brake system. A display on the instru-
ment panel will warn you if the brake fluid level is too low Ÿpage 70.
WARNING
Before opening the bonnet to check the brake fluid level, read and observe
the warnings Ÿpage 209.
Changing the brake fluid
The brake fluid must be renewed every two years.
We recommend that you have the brake fluid changed by an Authorised
Service Centre.
Before opening the bonnet, please read and follow the warnings Ÿ in
“Safety instructions on working in the engine compartment” on page 209 in
“Working in the engine compartment”.
Brake fluid absorbs moisture. In the course of time, it will absorb water from
the ambient air. If the water content in the brake fluid is too high, the brake
system could corrode. This also considerably reduces the boiling point of the
brake fluid. Heavy use of the brakes may then cause a vapour lock which
could impair the braking effect.
For this reason the brake fluid must be renewed every two years.It is important that you use only use brake fluid compliant with the US
standard FMVSS 116 DOT 4. We recommend the use of Genuine SEAT brake
fluid.
WARNING
Brake fluid is poisonous. Old brake fluid impairs the braking effect.
•Before opening the bonnet to check the brake fluid level, read and
observe the warnings Ÿpage 209.
•Brake fluid should be stored in the closed original container in a safe
place out of reach of children. There is a toxic risk.
•Have the brake fluid changed every two years at the latest. Heavy use
of the brakes may cause a vapour lock if the brake fluid is left in the system
for too long. This would seriously affect the efficiency of the brakes and the
safety of the vehicle. This may cause an accident.
Caution
Brake fluid could damage the paintwork. Wipe off any brake fluid from the
paintwork immediately.
For the sake of the environment
Brake fluid must be drained and disposed of in the proper manner observing
environmental regulations.

If and when 256
•Never start the engine when the vehicle is raised. Risk of accident. The
vehicle may fall from the platform due to the engine vibrations.
•When work is being carried out underneath the vehicle, it must be
secured using suitable frames. If not, an accident may occur.
•To lift the vehicle, only two-pillar or two-post lifting platforms with
sufficiently long arms and load-bearing capacity should be used.
•Lifting platforms with fluid filled cushions may not be used for lifting
the vehicle.
Caution
•The vehicle should never be lifted at the engine oil sump, the gearbox, or
the front or rear axle. This could cause serious damage to the vehicle.
•Before driving onto a lifting platform, you must check there is sufficient
clearance between low parts of the vehicle and the lifting platform.
WARNING (continued)

Technical Data 262
Te c h n i c a l D a t a
Checking fluid levels
From time to time, the levels of the different fluids in the
vehicle must be checked. Never fill with incorrect fluids, to do
so may cause serious damage to the engine.
Engine oil dipstick
Oil filler neck
Brake fluid reservoir
Vehicle battery (underneath a cover)
Coolant temperature deposit
Windscreen washer fluid reservoir
The checking and replenishment of the service fluids are carried out on the
components mentioned above. These operations are described in the
Ÿpage 209.Overview
Further explanations, instructions and restrictions on the technical data are
contained as of Ÿpage 257
Fig. 178 Diagram for the
location of the various
elements
A1
A2
A3
A4
A5
A6

Technical Data 264
Weights
Trailer weights
Engine oil capacity
Petrol engine 2.0l 85 kW (115 bhp). Automatic
General engine dataGross vehicle weightin kg 2430
Weight in working order (with driver)in kg 1653/1973
Gross axle weight, frontin kg 1210
Gross axle weight, rearin kg 980
Permitted roof loadin kg 75
With no brakes, gradients up to 12%700
With brakes, gradients up to 12%1800
Approximate engine oil capacity with oil filter change 4,0 litres
Power output in kW (bhp)rpm 85 (115)/ 5200
Maximum torquein Nm at rpm 170/ 2600-4200
No. of cylinders, capacity
in cm
34/ 1984
Compression 10
Fuel
Super 95 RON
a)/Normal 91 RONb)
a)Research-Octane-Number = Measure of the predetonation power of the petrol.b)With a slight power loss