seats Seat Alhambra 2011 Owner's Guide

114
Seats and storage compartments
Seats and storage compartments
Seat adjustment
Mec h
anical controls on the front seat Fig. 75 Front left seat
contr
o

ls.
The controls are mirrored for the front right-hand seat.
Mech
anically and electrically adjusted controls can be combined on the
seat. fig. 75 Function Necessary operations
1 Moving the head re-
str
aint

backwards or for-
wards. Pull the lever and move the seat for-
war
d
s. The front seat must be engag-
ed when the lever is released! 2 Adjusting the lumbar
sup
por

t*. Turn the lever. fig. 75 Function Necessary operations
3 Adjusting the backrest
angl
e. Turn the wheel.
4 Adjusting the seat
height. Pull the lever up or push down (sev-
eral
time

s if necessary) from its
home position. 

115
Seats and storage compartments
Electrical controls on the front seat* Fig. 76 Adjusting the
front
l
eft seat forwards or
backwards, the height,
the seat angle and the
front seat backrest. Fig. 77 Adjusting the
lumbar s
up

port.
The controls are mirrored for the front right-hand seat.
Mech
anically and electrically adjusted controls can be combined on the
seat. fig. 76 Press the control in the direction of the arrow:
A 1
Move the seat backwards or forwards.
2
and
3 Raise or lower the seat.
2
or
3 Adjust the seat angle.
B Forwards or
backwar ds. Adjust the backrest angle.
fig. 77 Press the corresponding area of the switch:
1
or
2 Adjust the curve of the lumbar support.
3
or
4 Adjust the height of the lumbar support.
WARNING
Using the front electric seats in a careless or uncontrolled manner may
le a

d to severe injuries.
● The front seats can also be electrically adjusted when the ignition is
switc
hed off. Never leave children or disabled people alone in the vehicle.
● In the event of an emergency, stop electrical adjustment by pressing
any b
utton. CAUTION
So as not the damage the electrical components of the front seats, do not
kneel on the se ats

or apply specific pressure to one point of the seat or
backrest. Note
● It may not be possible to electrically adjust the seat if the vehicle battery
i s

very low.
● Seat adjustment is stopped when the engine is started. Safety First Operating instructions Practical tips Technical Data

116
Seats and storage compartments
Adjusting the rear seats Fig. 78 Adjusting rear
seat
s. ⇒ fig. 7
5 Function Necessary operations
1 Adjusting the backrest
angl
e. Pull the lever and adjust the backrest
to the r
equir
ed position ⇒  . The
bac k
rest must be engaged when the
lever is released! There is a handle in-
stead of the lever on the third row of
seats and on the central seat of the
second row. It is used in the same
manner as the lever. 2 On the second row of
seat
s

only: Moving the
seat backwards or for-
wards. Pull the lever and move the seat for-
war
d
s or backwards. The seat must be
engaged when the lever is released! CAUTION
● Tilting the backrest of the second row of seats fully back could damage
the lug g

age compartment tray. Remove the tray before adjusting the back-
rest.
● Objects in the luggage compartment could cause damage when moving
the rear se
ats forwards or backwards. 

117
Seats and storage compartments
Seat functions Introduction Additional information and warnings
●
Adjust the seat position ⇒ page 10
● Se
at belts ⇒ page 21
● Airb

ag system ⇒ page 31
● Chi

ld seats (accessories) ⇒ page 39
● Int

egrated child seats ⇒ page 46
● Ext

erior mirrors ⇒ page 110
● L

uggage compartment ⇒ page 125 WARNING
Inappropriate use of the seat functions can cause severe injuries.
● Assume the proper sitting position before your trip and remain in it
throughout .

This also applies to the other occupants.
● Only adjust the seat position memory when the vehicle is stationary.
● Only switch the lumbar massage function on and off when the vehicle
is s

tationary.
● Keep hands, fingers, feet and other limbs away from the seat operat-
ing and adju
stment radius. Seat heating* Fig. 79 Detailed view of
the centr
e c

onsole: front
seat heating controls,
here with the second
temperature level set.
The seat cushions can be heated electrically when the ignition is switch on.
The back
rest is also heated in some versions.
Switch off seat heating if there is nobody in the seat. Function Action ⇒ fig. 79
To switch system on: Press button
. Seat
heating is switched on fully. Adjusting the heating
output: Keep pressing button  unti
l
the required intensi-
ty is set. The system switches
off: Keep pressing button  unti
l
all of the lights are
switched off ⇒ fig. 79. Safety First Operating instructions Practical tips Technical Data

118
Seats and storage compartments WARNING
People whose pain and temperature threshold has been affected by some
kind of medic
ine, paraplegia or chronic illness (e.g. diabetes) may sus-
tain burns to the back, buttocks and legs from use of the seat heating
that may lead to a long healing process or that may never completely
heal. Seek medical advice if you have doubts regarding your health.
● People with a limit pain and temperature threshold must never use
seat he
ating. CAUTION
● To avoid damaging the heating elements of the seat heating, please do
not kneel

on the seat or apply sharp pressure at a single point to the seat
cushion and backrest.
● Liquids, sharp objects and insulating materials on the seat could dam-
age the seat
heating.
● In the event of smells, switch off the seat heating immediately and have
the unit in
spected by a Technical Service. For the sake of the environment
The seat heating should remain on only when needed. Otherwise, it is an
unnec e

ssary fuel waste. Seat with position memory* Fig. 80 Memory buttons
on the outs
ide of

the
driver seat
Memory buttons
Individual settin
gs for the driver seat and the exterior mirror can be as-
signed to each memory button.
Storing exterior mirror settings for driving forwards
● Connect the automatic parking brake.
● Move the gear lever to neutral.
● Switch the ignition on.
● Adjust the front seat and the exterior mirrors.
● Keep the SET button held down for more than one second ⇒ fig. 80.
● Press the required memory button for the following 10 seconds. A sound
confirms the settin

gs have been stored.
Storing front passenger exterior mirror settings for driving in reverse gear
● Connect the automatic parking brake.
● Move the gear lever to neutral.
● Switch the ignition on. 

119
Seats and storage compartments
● Press the required memory button.
● Select
reverse gear.
● Adjust the front passenger exterior mirror so that you can see, for exam-
ple, the k
erb area.
● The new position of the mirror will be stored automatically and allocated
to the v
ehicle key that was used to unlock the vehicle.
Activating exterior mirror settings
● With the driver's door open and the ignition turned off, push the memo-
ry b
utton of the corresponding door briefly.
● ALTERNATIVELY: With the ignition swit
ched on, hold in the correspond-
ing memory button until the memorised position is reached.
To activate the memory function of the vehicle key
Important: a position must be memorised in the memory.
● Open the driver-side door.
● Press and hold any memory button.
● Within the following three seconds, push the button  to open the vehi-
cl e on the

vehicle key. A sound confirms the settings have been activated.
Adjusting the wing mirrors for driving and assigning driver seat settings to
a vehicle key
● Activate the memory function of the vehicle key
● Adjust the front seat and the exterior mirrors.
● Lock the vehicle. The settings are assigned to the vehicle key.
To deactiv
ate the memory function of the vehicle key
Important: a position must be memorised in the memory.
● Press and hold the SET button.
● Within the following ten seconds, push the button  to open the vehi-
cl e on the

vehicle key. A sound confirms the settings have been deactiva-
ted. Initialising the seat position memory
The position memor

y system must be initialised if, for example, the driver's
seat has been changed.
Initialisation deletes all memories and assignments for the seat with posi-
tion memory. The memory buttons can then be reprogrammed and the vehi-
cle keys re-assigned.
● Open the driver's door and do not get into the vehicle.
● Operating the seat settings from outside the vehicle.
● Move the angle of the backrest completely forwards.
● Release the control to set the angle and then press again until a sound
is he
ard. Note
The front passenger side wing mirror automatically changes from the posi-
tion st or

ed for reversing as soon as the vehicle moves forward at a speed of
at least 15 km/h or when the gear selection lever is changed to a position
other than R. Safety First Operating instructions Practical tips Technical Data

120
Seats and storage compartments
Convenient entry function for the third row of seats Fig. 81 Second row of
seat
s: c
onvenient entry
function controls.
The outer seats of the second row can be folded to make it easier to get in
and out of the thir
d row of seats.
Folding down the seat of the second row
● If necessary, open the belt loop and wind up the seat belt by hand.
● If necessary, remove the side head restraint of the integrated child seat
⇒ page 46.
● If

necessary, raise the armrests.
● Remove any objects located in the floor area of the second row of seats,
where app
licable ⇒  .
● Push the head restraint down as far as it will go ⇒ page 10.
● P

ush the lever ⇒ fig. 81 1 forwards and fold the backrest of the rear
seat .

The seat can still be moved forwards when rear seat is folded com-
pletely forwards ⇒  .
● Always take care when entering and leaving the vehicle ⇒  .Repositioning the seat of the second row
●
Lift the backrest of the rear seat in an upright position. The entire seat
fo l

ds backwards ⇒  .
● Make sure that the rear seat is securely engaged so that the seat belts
can pr o

vide proper protection in the rear seats. The red mark 2 should no
long er be
visible ⇒  in Folding down rear seats to create load space on
pag e 128.
Emer
gency exit function
If the lever 1 does not work, e.g. after an accident, the seats on the second
ro w c

an be folded forwards from the third row to allow occupants of the
third row of seats to get out of the vehicle ⇒  .
● Pull handle 3 back and fold the backrest of the rear seat. The complete
re ar se

at folds forward ⇒  .
WARNING
Careless or uncontrolled use of the convenient entry assistant may result
in sever e injur

y and accident.
● Never use the convenient entry function when the vehicle is in mo-
tion.
● Avoid trapping or damaging the seat belt when folding the rear seats
back.
● K

eep your hands, fingers, feet and other body parts out of the hinges
and the seat loc
king mechanism when folding and unfolding.
● Mats or other objects can be caught in the hinges of the backrests or
rear se
at. This could prevent the backrest from locking safely when posi-
tioned upright.
● All backrests must engage correctly for the seat belts on the rear
seats
to work properly. When the backrest of an occupied seat is not cor-
rectly locked in place, the passenger can be thrust forward with the back-
rest in case of sudden braking, sudden manoeuvres or an accident. 

121
Seats and storage compartments WARNING (Continued)
● A red mark on the side of the seat 2 indicates that the backrest is
not eng
aged. The mark is no longer visible when the backrest is correctly
engaged.
● If the backrest or seat are folded down and are not correctly locked in
plac
e, no passenger should use them.
● When getting in or out, never lean or hold onto the folded seat on the
second ro
w of seats. WARNING
If child seats are fitted to all the seats in the second row then it is possi-
bl e th

at the seats of this row cannot be folded down from the third row of
seats in case of an accident. In case of an emergency, passengers in the
third row of seats will not be able to leave the vehicle or to help them-
selves.
● Child seats should not occupy all the seats of the second row if other
pas
sengers are to occupy the third row of seats. CAUTION
● Before folding down the rear backrest for returning it to its position, ad-
ju s

t the front seats so that the head restraints and seatbacks do not hit off
each other when folding and unfolding.
● Any objects located in the floor area of the second row of seats may be
damag
ed on folding the rear seat forwards. Remove any objects before fold-
ing the seat down. Folding the backrest of the front passenger seat*
Fig. 82 Folding the back-
re
s

t of the front passeng-
er's seat. Fig. 83 Unlocking the
fo
l

ding backrest of the
front passenger's seat.
The backrest of the front passenger's seat can be folded and locked hori-
zontal
ly. Safety First Operating instructions Practical tips Technical Data

122
Seats and storage compartments
The front passenger's frontal airbag must be disconnected ⇒ page 31 if ob-
jects are being transported on the folded front passenger's seat.
Folding the backrest of the front passenger's seat
● Remove any objects from the front passenger's seat cushion ⇒  .
● Adjust the front passenger's seat to its lowest position ⇒ page 10.
● P

ush the head restraint down as far as it will go ⇒ page 10.
● Un

lock the backrest of the front passenger's seat in the direction of the
arrow
⇒ fig. 82 1 .
● Fold the backrest of the front passenger's seat forwards in the direction
of the arr o

w 2 until it is horizontal.
● The backrest of the front passenger's seat must engage safely in its fol-
ded pos ition.
Lif

ting the backrest of the front passenger seat
● Check that there are no objects or parts of the body in the hinge area.
● Lift the backrest of the front passenger's seat by first unlocking it again
⇒ fig. 83.
● Lift the backrest of the front passenger seat until it is upright. The back-
res

t must be engaged.
● The upright backrest of the front passenger's seat must safely engage. WARNING
Folding and lifting the backrest of the front passenger's seat uncontrolla-
bly or w

ithout paying attention may lead to severe injuries.
● Only fold and lift the backrest of the front passenger's seat when the
vehicl
e is stationary.
● While the backrest of the front passenger's seat is folded, the frontal
airbag mus
t remain disconnected and the PASSENGER AIRBAG OFF  light
on. WARNING (Continued)
● Keep your hands, fingers, feet and other body parts out of the hinges
and the se at

locking mechanism when folding and unfolding.
● Mats or other objects can be caught in the hinges of the backrest of
the front p
assenger's seat. This could prevent the backrest from locking
safely when positioned upright.
● The upright backrest of the front passenger's seat must engage. If the
back
rest of the front passenger's seat is not locked, it may suddenly
move and cause severe injuries. WARNING
Seat anchors and hinges exposed when the backrest of the front pas-
seng er's

seat is folded may lead to severe injuries in the event of an acci-
dent or sudden braking.
● Never carry people or children on the front passenger's seat when the
back
rest is folded.
● When the backrest of the front passenger's seat is folded, only the
outer seat
behind the driver on the second row of seats may be occupied.
This also applies to children sitting in a child seat. 

123
Seats and storage compartments
Head restraints Adjus tin
g the head restraints Fig. 84 Adjusting the
front
he

ad restraints. Fig. 85 Adjusting the
re
ar he

ad restraints.
All seats are equipped with a head restraint. Adjusting height
●
Push the head restraint up or down in the direction of the arrow with the
button pr
essed ⇒ fig. 84 1 or ⇒ 
fig. 85 1 ⇒  .
● The head restraint must engage securely in position. There are three
pos s

ible positions on the second row of seats and two possible positions
on the third row of seats.
Correct adjustment of head restraints
Adjust the head restraint so that its upper edge is at the same level as the
top of your head, or as close as possible to the same level as the top of your
head and under no circumstances below eye level. Keep the back of your
neck as close as possible to the head restraint.
Adjusting the head restraint for short people
Lower the head restraint completely, even if your head is below its upper
edge. When the head restraint is at its lowest, it is possible that a small gap
remains between it and the backrest.
Adjusting the head restraint for tall people
Raise the head restraint completely. WARNING
Travelling with the head restraints removed or improperly adjusted in-
cr e

ases the risk of severe or fatal injuries in the event of accidents and
sudden braking or manoeuvres.
● Always fit and adjust the head restraint properly whenever a person
is oc
cupying a seat.
● All occupants must correctly adjust the head restraint according to
their height to r
educe the risk of back injuries in the event of an accident.
The upper edge of the head restraint must be as close as possible to the
same level as the top of your head and under no circumstances below eye
level. Keep the back of your neck as close as possible to the head re-
straint.
● Never adjust the head restraint while the vehicle is in motion. 
Safety First Operating instructions Practical tips Technical Data