head light Seat Alhambra 2012 Owner's Guide

330If and when
Changing bulbs
Introduction
Changing bulbs requires a certain amount of manual skill. If you are unsure,
SEAT recommends that you consult an Technical Service or request assis-
tance from a specialist. In general, a specialist is required if other vehicle
components must be removed or if the discharge lamps must be replaced.
You should store spare light bulbs in the vehicle for safety-relevant lights.
Spare bulbs may be obtained from the Technical Services. In some coun-
tries, it is a legal requirement to carry spare bulbs in the vehicle.
Driving with faults and blown bulbs on the vehicle exterior lighting is
against the law.
Additional bulb specifications
The specifications of some headlamp bulbs and bulbs for the tail lamps fit-
ted at the factory may be different to those of conventional bulbs. Bulb in-
formation is displayed on the bulb socket or on the bulb itself.
Additional information and warnings:
● Lights and visibility ⇒ page 95
● Working in the engine compartment ⇒ page 279
● Vehicle tools ⇒ page 324
● Fuses ⇒ page 326
WARNING
If the road is not well-lit and the vehicle is not clearly visible to other
drivers, there is a risk of accident.
WARNING
Failure to replace bulbs correctly may cause serious accidents.
● Before carrying out any work in the engine compartment please read
and observe the warnings ⇒ page 279. In any vehicle, the engine com-
partment is a hazardous area and could cause severe injury.
● Discharge lamps work with high-voltage and can cause serious or fa-
tal injury if handled incorrectly.
● H7 and discharge lamps are highly pressurised and could explode
when being changed.
● Only replace the bulbs concerned when they have cooled.
● Never replace bulbs alone if you are not familiar with the operations
necessary. If you are not sure about procedures then visit a Technical
Service to carry out the necessary work.
● Never touch the bulb glass directly. Fingerprints will be evaporated by
the heat of the operating bulb thus “fogging” up the reflector.
● The headlamp frameworks in the engine compartment and the tail
lamps contain sharp elements. Always protect your hands when chang-
ing bulbs.
CAUTION
After changing a bulb, if the rubber covers and plastic caps are not replaced
correctly on the headlamp framework, the electrical installation may be
damaged, especially if water is allowed to enter. 
Indicator
lights upPossible causeSolution
A vehicle exterior lighting
bulb is not working.Replace the faulty bulb. 

331
If and when
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Checking the bulbs of a trailer
For vehicles with the factory fitted trailer system, certain trailer lights are al-
so controlled if the socket is correctly connected.
A fault on a trailer turn indicator is indicated on the instrument panel by the
indicator blinking twice as fast (  or ) ⇒ page 95.
● General fault of all indicators on one side.
● Fault in one tail light (on some models, also the registration light).
● Fault in two brake lights.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
● Never ignore the warning lamps or text messages.
● Stop the vehicle safely as soon as possible.
CAUTION
Failure to heed the warning lamps and text messages when they appear
may result in faults in the vehicle.
Note
A fault in the LED on the tail lights will not be indicated. However, if the fault
affects all the LEDs then this will be indicated by the indicator . Information for replacing bulbs
Checklist
To replace a bulb, carry out the following operations always in the order giv-
en ⇒ 
:
Park the vehicle a safe distance from traffic and on suitable ground.
Connect the electronic parking brake ⇒ page 185.
Turn the light switch to position 0 ⇒ page 95.
Move the gear lever into the neutral position ⇒ page 95.
Automatic gearbox: Move selector lever to position P ⇒ page 176.
Stop the engine and remove the key from the ignition ⇒ page 172.
Manual gearbox: Select a gear ⇒ page 176.
Wait until all of the passenger compartment lights are turned off
⇒ page 95.
Allow the corresponding bulb to cool. Visually inspect fuses to see if any are blown ⇒ page 326.
Replace the bulb according to the instructions ⇒ 
. Bulbs should only
be replaced by new identical models. Bulb information is displayed on
the bulb socket or on the bulb itself.
In general, never touch the bulb glass directly. The heat of the bulb
would cause the fingerprint to evaporate and condense on the reflector.
This will impair the brightness of the headlight.
Check if the new bulb is working. If the bulb is not working, it may not
have been correctly fitted, it could be damaged or the connector may
not be correctly connected.
Every time a bulb for the headlights is replaced, visit a specialised
workshop to check the headlights. 
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Safety FirstOperating instructionsPractical tipsTechnical Specifications

332If and when
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
● Always complete the operations given in the checklist and observe
the general rules of safety.CAUTION
Always remove and fit headlights carefully to avoid damage to the paint-
work and other vehicle parts. 
To replace halogen headlight bulbs
Fig. 205 In the engine
compartment: Left-hand
side headlight lining. A
dipped beam headlights,
B daytime driving lights
and C main beam head-
lights and side lights.Fig. 206 Left headlight
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:
fig. 205, fig. 206 ABCIndicators (small lamp holder)Dipped beam head-lightsDaytime driving lightMain beam headlightsSide lights
1.Always take the checklist into account and take the necessary actions ⇒ page 331.2.Open the bonnet  ⇒ page 279. 

333
If and when
fig. 205,
fig. 206 ABCIndicators (small lamp holder)Dipped beam head-lightsDaytime driving lightMain beam headlightsSide lights
3. Remove the rubber cover on the rear of the headlight.
4.
Rotate the lamp holder1 to the left all the way
and pull it out back-
wards with the bulb.Rotate the lamp holder to the left all the way and pull it out backwards with the bulb.Press the wire clip down-wards and pull the lamp holder 2
out with the
bulb.
Pull the lamp holder 3out backwards with the
bulb.
5.Depending on the model, the bulb is removed directly from the lamp holder or it may need to be rotated and then removed.6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the headlight and rotate to the right all the way.
Place the lamp holder in
the headlight and pull the
wire clip upwards until it
clicks into place.Place the lamp holder inthe headlight and insert completely.
8. Insert the rubber cover.
Note
The images show the left hand headlight from behind. The structure of the
right hand side headlight is symmetric. 
Safety FirstOperating instructionsPractical tipsTechnical Specifications

334If and when
To replace the xenon headlights bulb
Fig. 207 In the engine
compartment: Turn signal
cover.
Fig. 208 Turn signal in-
dicator lamp holder 1
and turning light 2.
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:
Turn signal indicators 1Turning lights 2
1.Always take the checklist into account and take the necessary ac-
tions ⇒ page 331.
2.Open the bonnet  ⇒ page 279.
3.Rotate the cover ⇒  fig. 207 in the direction of the arrow and remove
it.
4.
Rotate the lamp holder 1⇒ fig. 208 to the left all the way
and pull it out backwards with
the bulb.Press the wire clip downwards
and pull the lamp holder 2
⇒ fig. 208 out with the bulb.
5.Depending on the model, the bulb is removed directly from the
lamp holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the
headlight and rotate to the right
all the way.Place the lamp holder in the
headlight and pull the wire clip
upwards until it clicks into place.
8.Rotate the cover ⇒  fig. 207 in the opposite direction to the arrow as
far as it will go.
Always seek the help of a specialist when changing the Xenon dipped beam
and full beam headlamps ⇒  in Introduction on page 330.
Note
The illustrations show the left hand headlight. The structure of the right
hand side headlight is symmetric. 

335
If and when
To replace the front bumper bulbs
Fig. 209 On the right-
hand side of the front
bumper: Removing the
headlights
Fig. 210 Changing the
bulbs in the headlights.
Complete operations only in the sequence given:
1.Always take the checklist into account and take the necessary ac-
tions ⇒ page 331.
2.Pull the cover forwards, in the direction of the arrow ⇒ fig. 209.
3.Unscrew the attachment screw ⇒ fig. 209 1 using the screwdriver
from the on-board tools ⇒ page 324.
4.Tilt the headlight slightly forward and extract it from its lateral at-
tachments ⇒ fig. 210 (small arrows).
5.Release the connector ⇒ fig. 210 1 and remove it.
6.Rotate the lamp holder ⇒ fig. 210 2 to the left all the way, in the
direction of the arrow, and pull it out backwards with the bulb.
7.Replace the faulty bulb by a new identical bulb.
8.Place the bulb holder in the headlight and rotate to the right all the
way.
9.Insert the connector ⇒ fig. 210 1 on the lamp holder
⇒ fig. 210 2. The connector must audibly click into place.
10.Place the headlight into its position
⇒ fig. 210 (small arrows) and
tilt it backwards.
11.Tighten the attachment screw ⇒ fig. 209 1 using the screwdriver.12.Replace the cover on the bumper ⇒ fig. 209.
Safety FirstOperating instructionsPractical tipsTechnical Specifications

343
If and when
The vehicles should not touch. Otherwise, current may be allowed to flow
when the positive poles are connected.
Connect the clamps so they have good metal-to-metal contact with the ter-
minals.
If the engine fails to start straight-away, switch off the starter after about 10
seconds and try again after about a minute.
Complete operations only in the sequence given.
Jump lead terminal connections
● Switch off the ignition of both vehicles ⇒ page 172.
● Likewise, open the battery cover in the engine compartment
⇒  page 292, or remove the positive pole cap from one side 1)
, in the direc-
tion of the arrow ⇒ fig. 217.
● Connect one end of the red jump lead to the positive terminal
⇒  fig. 218 +
or ⇒ 
fig. 217 + of the vehicle with the flat battery A ⇒ .
● Connect the other end of the red jump lead to the positive terminal + in
the vehicle providing assistance B.
● For vehicles without Start-Stop system: Connect one end of the black
jump lead to the negative terminal -
in the vehicle providing assistance
B ⇒ fig. 218.
● For vehicles with Start-Stop system: Connect one end of the black X
jump lead to a suitable ground connection, a solid piece of metal in the en-
gine block, or to the engine block
⇒ fig. 219.
● Connect the other end of the black jump lead X
to a solid metal compo-
nent connected to the engine block, or onto the engine block itself of the
vehicle with the flat battery however, connect it as far away as possible from
the battery A
⇒ .
● Place the leads so that they cannot be caught by any moving parts in the
engine compartment. Switching on
●
Start the engine of the vehicle supplying current and let it run at idling
speed.
● Start the engine of the car with the flat battery and wait two or three mi-
nutes until the engine is “running smoothly”.
Removing the jump leads
● Before you remove the jump leads, switch off the headlights (if they are
switched on).
● Turn on the heating and rear window heater in the vehicle with the flat
battery. This helps minimise voltage peaks which are generated when the
leads are disconnected.
● With the engines running, disconnect the leads in reverse order to con-
nection.
● Close the battery cover, or replace the positive pole cap 1)
.
WARNING
Incorrectly jump starting could cause the battery to explode resulting in
serious injury. Please observe the following rules to minimise the risk of
a battery explosion:
● All work involving the vehicle battery and electrical system can cause
corrosion, fire and serious electric shocks. Always read and take into ac-
count the safety warnings and standards before beginning work on the
battery ⇒ page 292, Vehicle battery.
● Always protect your eyes with suitable working goggles and never
lean over the vehicle battery.
● The jump leads must be connected in the correct order: first the posi-
tive cable, then the negative cable. 
1)
Vehicles whose battery is not located in the engine compartment ⇒ page 342.
Safety FirstOperating instructionsPractical tipsTechnical Specifications

367
Technical specifications
Dimensions and capacities
DimensionsLength, width 4854 mm1904 mmHeight at kerb weight 1720 mmFront and rear projection Wheelbase 2919 mmTurning circle
Track width a)FrontRear1557 – 1569 mm1605 – 1617 mmCapacitiesFuel tank 70 litres. Reserve 8 litres.Windscreen washer fluid container with headlight washer 3.5 l/ 6 lTyre pressureSummer-grade tyres:The correct tyre pressure can be seen on the sticker on the inside of the tank flap.Winter tyres:The pressure of these tyres is the same as the summer tyre pressure plus 0.2 bar.a)
This data will change depending on the type of wheel rim.
CAUTION
● Special care should be taken when parking in areas with high kerbs or
fixed barriers. Objects protruding from the ground may damage the bumper
or other parts of the vehicle during manoeuvres.
● Special attention is required when driving through entrances, over
ramps, kerbs or other objects. The vehicle underbody, bumpers, mudguards
and running gear, and the engine and exhaust system could be damaged as
you drive over these objects. 
Safety FirstOperating instructionsPractical tipsTechnical Specifications

Index
A
AbroadExtended stay abroad with your vehicle . . 259
Sale of vehicle . . . . . . . . . . . . . . . . . . . . . . 259
ABS See "Brake assist systems" . . . . . . . . . . . . 191
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Acoustic warnings Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Adaptive headlights Dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
AdBlue Control lamp . . . . . . . . . . . . . . . . . . . . . . . . 275
Information . . . . . . . . . . . . . . . . . . . . . . . . . 276
Minimum quantity for a refill . . . . . . . . . . . 276
Refilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Specifications . . . . . . . . . . . . . . . . . . . . . . . 278
Tank filling capacity . . . . . . . . . . . . . . . . . . 276
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . 275
Additional equipment . . . . . . . . . . . . . . . . . . . 262
Additional heater See "Auxiliary heater" . . . . . . . . . . . . . . . . 165
Adjusting passenger exterior mirror . . . . . . . . 112
Adjustment Correct sitting position . . . . . . . . . . . . . . . . 12
Electric front seat . . . . . . . . . . . . . . . . . . . . 115
Head restraints . . . . . . . . . . . . . . . . . . . . . . 123
Mechanical front seat . . . . . . . . . . . . . . . . 114
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Seat with position memory . . . . . . . . . . . . 118
Steering wheel . . . . . . . . . . . . . . . . . . . . . . 171
Adjustments Folding the backrest of the front passengerseat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Headlight range . . . . . . . . . . . . . . . . . . . . . 101
Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Aerial built into the window . . . . . . . . . . . . . . . 259
AFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . 28, 31 Cleaning instrument panel . . . . . . . . . . . . 257
Curtain airbags . . . . . . . . . . . . . . . . . . . . . . . 37
Deactivating the front passenger airbag . . 35
Deactivating using the key switch . . . . . . . . 35
Description . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Differences between front passenger airbagsystems . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . 33
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Knee airbag . . . . . . . . . . . . . . . . . . . . . . . . . 38
Locking the vehicle after airbag deploy- ment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . 36
Use of child seats . . . . . . . . . . . . . . . . . . . . . 35
Vehicle care . . . . . . . . . . . . . . . . . . . . . . . . 257
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 30
Air conditioner Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Air conditioning
see "Climate control" . . . . . . . . . . . . . . . . . 157
Air recirculation mode . . . . . . . . . . . . . . . . . . . 163
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Alcantara . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
All-wheel drive Snow chains . . . . . . . . . . . . . . . . . . . . . . . . 305
Winter tyres . . . . . . . . . . . . . . . . . . . . . . . . . 304
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Ambient lighting . . . . . . . . . . . . . . . . . . . . . . . 102
Anodized surfaces . . . . . . . . . . . . . . . . . . . . . . 251
Anti-lock brake system (ABS) . . . . . . . . . . . . . 191
Anti-theft alarm Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Anti-theft alarm system False alarms . . . . . . . . . . . . . . . . . . . . . . . . . 79
Anti-theft bolts . . . . . . . . . . . . . . . . . . . . . . . . . 325
Anti-theft locking bolts . . . . . . . . . . . . . . . . . . 309
Anti-theft wheel locking bolts . . . . . . . . . . . . . 311
Anti-tow system . . . . . . . . . . . . . . . . . . . . . . . . . 79
Anti-trap function Electric windows . . . . . . . . . . . . . . . . . . . . . . 90
Panorama sliding sunroof . . . . . . . . . . . . . . 94
Sunshade . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
Antitheft alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 78
369
Index

Brake assist systems . . . . . . . . . . . . . . . . . . . . 191
Brake assist system (BAS) . . . . . . . . . . . . . . . . 192
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Specification . . . . . . . . . . . . . . . . . . . . . . . . 194
Brakes Brake assist systems . . . . . . . . . . . . . . . . . 191
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . 193
Brake fluid level . . . . . . . . . . . . . . . . . . . . . 194
Brake pads . . . . . . . . . . . . . . . . . . . . . . . . . 189
Changing the brake fluid . . . . . . . . . . . . . . 194
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . 186
Emergency brake indicator in case of sud-den braking . . . . . . . . . . . . . . . . . . . . . . . 317
Running-in brake pads . . . . . . . . . . . . . . . . 189
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . 186
Brake servo . . . . . . . . . . . . . . . . . . . . . . . . 189, 191
Brake system Malfunction . . . . . . . . . . . . . . . . . . . . . . . . 189
Brake systems . . . . . . . . . . . . . . . . . . . . . . . . . 191
Braking assist . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Brake assist system (BAS) . . . . . . . . . . . . . 192
Breakdown Securing the vehicle . . . . . . . . . . . . . . . . . 316
Bulb fault See changing bulbs . . . . . . . . . . . . . . . . . . 330
C
Card compartments . . . . . . . . . . . . . . . . . . . . . 145
Care See "Care of your vehicle" . . . . . . . . . . . . . 246
Vehicle interior . . . . . . . . . . . . . . . . . . . . . . 253 Care of your vehicle
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Caring for paintwork . . . . . . . . . . . . . . . . . . . . . 251
Carrier system . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Catalytic converter . . . . . . . . . . . . . . . . . . . . . . 233 Malfunction . . . . . . . . . . . . . . . . . . . . . . . . 233
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . 232
CD changer . . . . . . . . . . . . . . . . . . . . . . . . 142, 149
Central locking . . . . . . . . . . . . . . . . . . . . . . . 74, 77 Antitheft alarm . . . . . . . . . . . . . . . . . . . . . . . 78
Locking/unlocking the vehicle . . . . . . . . . . 76
Central locking system After airbag deployment . . . . . . . . . . . . . . . 75
Description . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Opening doors individually . . . . . . . . . . . . . 75
Centre armrest . . . . . . . . . . . . . . . . . . . . . . . . . 126
Changing Windscreen wiper blades . . . . . . . . . . . . . 250
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . 309 Changing a wheel . . . . . . . . . . . . . . . . . . . 315
Preparations . . . . . . . . . . . . . . . . . . . . . . . . 310
Raising the vehicle . . . . . . . . . . . . . . . . . . . 313
Wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . 311
Changing bulbs . . . . . . . . . . . . . . . . . . . . . . . . 330 Bodywork . . . . . . . . . . . . . . . . . . . . . . . . . . 337
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
Front bumper . . . . . . . . . . . . . . . . . . . . . . . 335
Halogen headlights . . . . . . . . . . . . . . . . . . 332
Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
Initial operations . . . . . . . . . . . . . . . . . . . . 331
Number plate light . . . . . . . . . . . . . . . . . . . 339
Sea changing bulbs . . . . . . . . . . . . . . . . . . 330 Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Tail lights . . . . . . . . . . . . . . . . . . . . . . 336, 337
Xenon headlights . . . . . . . . . . . . . . . . . . . . 334
Changing gear . . . . . . . . . . . . . . . . . . . . . . . . . 176 Automatic gearbox . . . . . . . . . . . . . . . . . . . 180
Engaging gears (manual gearbox) . . . . . . 179
Manual gearbox . . . . . . . . . . . . . . . . . . . . . 179
Manually unlocking the gear selection lev-er . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Selecting gears (automatic gearbox) . . . . 180
Warning and control lamps . . . . . . . . . . . . 177
Changing gears Gear recommendation . . . . . . . . . . . . . . . . 184
Tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Changing the battery of the vehicle key . . . . . . . . . . . . . . . . . . . . . 73
Changing the wheel After changing the wheel . . . . . . . . . . . . . . 315
Checking Tyre pressures . . . . . . . . . . . . . . . . . . . . . . . 302
Checking the oil level . . . . . . . . . . . . . . . . . . . . 285
Check list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Checklist Before working in the engine compart-ment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Changing bulbs . . . . . . . . . . . . . . . . . . . . . 331
In case of an emergency . . . . . . . . . . . . . . 316
Check list Preparations for changing a wheel . . . . . . 310
Raising the vehicle with the jack . . . . . . . . 314
Checklist Refilling precautions . . . . . . . . . . . . . . . . . 271
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
371
Index