left Seat Leon 5D 2013 Workshop Manual

296Fuses and bulbs
Turn signal bulb
Fig. 183 Turn signal bulb
Fig. 184 Turn signal bulb
– Raise the bonnet
– Move the loop ⇒ Fig. 183 1
in the direction of the arrow and
remove the cover.
– Turn the bulb holder ⇒ Fig. 184 2
to the left and pull.
– Remove the bulb by pressing on the bulb holder and turning it
anti-clockwise at the same time.
– Installation involves all of the above steps in reverse sequence. Main beam bulb
Fig. 185 Main beam
bulb
Fig. 186 Main beam
bulb
– Raise the bonnet
– Move the loop ⇒ Fig. 185 1
in the direction of the arrow and
remove the cover.
– Slide connector ⇒ Fig. 186 2
to the left or right and pull.
– Remove the bulb by disconnecting the connector.
– Installation involves all of the above steps in reverse sequence. 

298Fuses and bulbs
Fog light, FR version
Fig. 189 Fog light: ac-
cess to the connector
and to the light bulb
holder
Fig. 190 Fog light: ac-
cess to the connector and
to the light bulb holder
– Remove the 3 screws A
⇒ Fig. 189 from the inside of the wheel
housing and the 2 bottom screws B ⇒ Fig. 189 from the bump-
er using a screwdriver. –
Pull the wheel housing 1
⇒ Fig. 190 to access the 2 hidden
screws C ⇒ Fig. 190 in the bumper.
– Remove the screws using a screwdriver.
– Pull the bumper to release it from its anchorages to access the
connector and the light bulb holder.
Note
Due to the difficulty of accessing fog light bulbs, have them replaced at a
Technical Service or specialised workshop. 
Remove the bulb holder
Fig. 191 Front fog light
– Remove connector ⇒ 
Fig. 191 A
from the bulb.
– Turn bulb holder ⇒ 
Fig. 191 B
to the left and pull. 

301
Fuses and bulbs
Changing tail light bulbs (on rear lid)
Overview of tail lights
Rear lights on tailgate
Left sideSide lights2x W5W LLFog lightsH21 WRight sideSide lights2x W5W LLReverse lightP21W LL
The above table corresponds to a right-hand traffic vehicle. The position of
lights may vary according to the country. Remove the bulb holder
The rear lid must be open to change the bulbs.
Fig. 195 Remove the
cover from the rear lid
Fig. 196 Remove the
bulb holder
– Remove the rear lid cover in the direction indicated ⇒ Fig. 195. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

302Fuses and bulbs
–Unlock the retaining tabs A
of the bulb holder, following the
direction of arrows 1 and 2 ⇒ Fig. 196.
– Remove the bulb holder by turning it in the direction of arrow
3
⇒ Fig. 196. 
Changing bulbs
Fig. 197 Position of the
bulbs in the bulb holder
– Lightly press the defective bulb into the bulb holder ⇒ Fig. 197
1
, then turn it to the left 2 and remove it.
– Fit the new bulb, pressing it into the bulb holder and turn it to
the right as far as it will go.
– Use a cloth to remove any fingerprints from the glass part of the
bulb.
– Check that the new bulb works properly.
– Replace the bulb holder.
Note
For LED pilots, you can only change the fog or reverse bulb, on the left or
right guide. 
Fitting the bulb holder
– Install the bulb holder making sure that locking clips ⇒ Fig. 196
A are properly clipped on.
– Replace the cover of the rear lid lining ⇒ Fig. 195.