fuses Seat Toledo 2012 User Guide

214Fuses and bulbs
Changing fuses in the engine compartment
Fig. 144 Battery: fuse cover (version 1)
Fig. 145 Battery: fuse cover (version 2)
●Press the flexible tabs on the fuse box cover in the direction indicated by
the arrows 1

⇒  Fig. 144.
● Remove the cover by sliding it in the direction indicated by arrow 2.
● Use a flat-headed screwdriver to unlock the holes 3.
● Open the cover in the direction indicated by the arrow 4.Changing bulbs
Introduction
Changing bulbs requires a certain degree of practical skill. If in doubt, we
recommend you have defective bulbs changed by a specialised service or,
in case of an emergency, seek professional assistance.
● Switch off the ignition and all of the lights before changing a bulb.
● Do not touch the glass part of the bulb with your bare hands. The finger-
prints left on the glass will vaporise as a result of the heat generated by the
bulb, causing a reduction in bulb life and condensation on the mirror sur-
face, thus reducing efficiency.
● A bulb must only be replaced by one of the same type. The type is indi-
cated on the bulb, either on the glass part or on the base.
● There is a storage area for the bulb box in the spare wheel well or below
the carpet in the luggage compartment.
The light source used for each function is listed below:
Double headlights
H7 Long Life
H7
W5W Long Life PY21W NA P21W Super Long Life 
Dipped beam:
Main beam:
Side lights:
Turn signals:
Daytime driving lights:

215
Fuses and bulbs
WARNING
● Take particular care when working on components in the engine com-
partment if the engine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
● The high voltage element of gas discharge bulbs* (xenon light) must
be handled correctly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not to injure yourself on sharp
parts in the headlight housing.
CAUTION
● Remove the ignition key before working on the electric system. Other-
wise, a short circuit could occur.
● Switch off the lights and the parking light before changing a bulb.
For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in the prop-
er manner.
Note
● Depending on weather conditions (cold or wet), the front lights, the fog
lights, the rear lights and the turn signals may be temporarily misted. This
has no influence on the useful life of the lighting system. By switching on
the lights, the area through which the beam of light is projected will quickly
be demisted. However, the edges may remain misted.
● Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the inter-
est of your own safety, but also in that of all other road users. ●
Before changing a bulb, make sure you have the correct new bulb.
● Do not touch the glass part of the bulb with your bare hands, use a cloth
or paper towel instead. Otherwise, the fingerprints left on the glass will va-
porise as a result of the heat generated by the bulb, they will be deposited
on the reflector and will impair its surface. 
Double headlight bulbs
Fig. 146 Main headlight
bulbs
Installation position of double headlight bulbs side light
main beam headlight
dipped beam headlight
turn signal light
daytime driving light 
A
BCDE
Safety FirstOperating instructionsPractical TipsTechnical specifications

216Fuses and bulbs
Changing side light bulbs
Fig. 147 Changing side
light bulbs
– Raise the bonnet.
– Remove the protective cover ⇒ Fig. 147.
– Remove the bulb holder ⇒ Fig. 147 1
by pulling it outwards.
– Remove the bulb by pulling it out and fit the new one.
– Installation involves all of the above steps in reverse sequence.
– Fit the protective cover. Make sure that the cover fits correctly
on the housing during the operation.
– Check that the new bulb works properly. Changing main beam headlight bulbs
Fig. 148 Changing main
beam headlight bulbs
– Raise the bonnet.
– Remove the protective cover.
– Remove the connector ⇒ Fig. 148 1
by pulling it outwards.
– Extract the bulb and fit the replacement so that it fits correctly
into the recess on the reflector.
– Installation involves all of the above steps in reverse sequence.
– Fit the protective cover. Make sure that the cover fits correctly
on the housing during the operation.
– Check that the new bulb works properly. 

217
Fuses and bulbs
Changing dipped beam headlight bulbs
Fig. 149 Changing dip-
ped beam headlight
bulbs: wheel housing
Fig. 150 Changing dip-
ped beam headlight
bulbs
– Turn the wheel for access to the wheel housing cover and re-
move the cover ⇒ Fig. 149.
– Remove the protective cover from the headlight ⇒ 
Fig. 150.
– Remove the connector ⇒ 
Fig. 150 1
by pulling it outwards.
– Unclip the retainer spring ⇒ 
Fig. 150 2
pressing clockwise and
inwards. –
Extract the bulb and fit the replacement so that the lug on the
base fits into the recess on the reflector.
– Fit the connector.
– Fit the protective cover. Make sure that the cover fits correctly
on the housing during the operation.
– Replace the wheel housing cover.
– Check that the new bulb works properly. 
Changing turn signal light bulbs
Fig. 151 Changing turn
signal light bulbs
– Raise the bonnet.
– Turn the bulb holder ⇒ Fig. 151 1
anti-clockwise and remove
it.
– Remove the bulb by pressing on the bulb holder and turning it
anti-clockwise at the same time. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

218Fuses and bulbs
–Fit the replacement bulb in the bulb holder and turn clockwise
as far as it will go.
– Check that the new bulb works properly. 
Changing daytime driving light bulbs
Fig. 152 Changing day-
time driving light bulbs
– Raise the bonnet.
– Turn the bulb holder ⇒ Fig. 152 1
anti-clockwise and remove
it.
– Remove the bulb by pressing on the bulb holder and turning it
anti-clockwise at the same time.
– Fit the replacement bulb in the bulb holder and turn clockwise
as far as it will go.
– Check that the new bulb works properly. 

219
Fuses and bulbs
Changing front fog light bulbs
Front fog light bulb
Fig. 153 Front fog light
Fig. 154 Front fog light –
Remove the screw ⇒ Fig. 153 A
from the fog light grill with a
screwdriver.
– Subsequently, remove the clips located on the edge of the grill
with gentle leverage.
– Remove the screws (3x) ⇒ Fig. 154 B
to remove the front fog
light.
– Remove the metal clip located at the top of the front fog light by
pulling it towards you ⇒ Fig. 154 C
. 
Removing the bulb holder
Fig. 155 Front fog light
– Remove the connector ⇒ Fig. 155 A
from the bulb.
– Turn the bulb holder ⇒ Fig. 155 A
anti-clockwise and pull it out
of the fog light housing. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

220Fuses and bulbs
–Remove the bulb by pressing on the bulb holder and turning it
anti-clockwise at the same time.
– Installation involves all of the above steps in reverse sequence.
– Check that the bulb works properly. 
Changing bulbs for rear lights (in side panel) Removing tail light
Fig. 156 Remove rear
light unit from side panel
Check which of the bulbs is defective.
– Open the luggage compartment to access the rainduct area.
– Take the screwdriver or a Torx 20 key (T20) from the vehicle tool
kit and loosen (turning anti-clockwise) and remove the two re-
taining screws that secure the front of the light ⇒ Fig. 156 1
,
taking care not to lose them. –
Pull the rear light unit backwards ( ⇒ Fig. 156 2
) to remove the
light from its housing. 
Removing the bulb holder
Fig. 157 Light connector
at the rear of the rear
light unit
Fig. 158 Retaining
screws on reverse side of
rear light unit
– Disconnect the light connector A
⇒ Fig. 157 by moving its side
levers (arrows) and pulling the connector outwards.
– Place the light on a level, horizontal surface on top of a soft
cloth so as not to scratch the outer glass. 

221
Fuses and bulbs
– Unscrew the four retaining screws from the bulb holder anti-
clockwise using a screwdriver or a Torx 20 key (T20) from the ve-
hicle tool kit ⇒ Fig. 158. Take care not to lose the bulb holder
retaining screws. 
Changing bulbs
All bulbs can be changed easily in the bulb holder.
Fig. 159 Position of the
bulbs in the bulb holder
The bulbs are secured with a bayonet fastener. The table below
gives an overview of the bulbs.
– Lightly press the defective bulb into the bulb holder, then turn it
anti-clockwise and remove it.
– Fit the new bulb, pressing it into the bulb holder and turn it
clockwise as far as it will go.
– Use a cloth to remove any fingerprints from the glass part of the
bulb. –
Check that the new bulb works properly.
– Replace the bulb holder.
– Screw in the bulb holder using the four screws, turning them
clockwise.
List of bulbs
Position: ⇒ Fig. 159Bulb functionATurn signals: PY21W NA LLBSide lights-brake lights: P21/5WCSide lights: P21/5W
Note
Check the condition of the seal. If damaged, a replacement can be acquired
from an Official Service. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

222Fuses and bulbs
Fitting rear light
Fig. 160 Fitting tail light
unit
Fig. 161 Fitting tail light
unit
– Make sure the connector is correctly in place.
– Press the rear light unit backwards (driving direction) by fitting
the fastenings into the rubber mountings ⇒ Fig. 160 A
.
– Take the screwdriver or a Torx 20 key (T20) from the vehicle tool
kit and tighten (turning clockwise ⇒ 
Fig. 161) the two retaining
screws that secure the front of the light. 

223
Fuses and bulbs
Changing rear lights (in rear lid) Removing the bulb holder
The rear lid must be open to change the bulbs.
Fig. 162 Remove the
cover from the rear lid
Fig. 163 Remove the bulb holder You can access the bulb holder for the inner rear lights from the in-
side of the rear lid.
–
Check which of the bulbs is defective.
– Open the cover to access the lights, turning it by hand in the di-
rection indicated by the arrows.
– Access the lights by disconnecting the connector 1
⇒ Fig. 163
 and unscrewing the bulb holder ⇒ Fig. 163 . Take care not
to lose the bulb holder retaining screw.
– Change the bulbs ⇒ page 223. 
Changing bulbs
All bulbs can be changed easily in the bulb holder.
Fig. 164 Position of the
bulbs in the bulb holder
The bulbs are secured with a bayonet fastener. The table below
gives an overview of the bulbs ⇒ table on page 224. 
Safety FirstOperating instructionsPractical TipsTechnical specifications