instrument panel Seat Toledo 2012 User Guide

79
Communication
ButtonRadioCD/MP3/USB*/iPod ®
*AUXNAVIGATORTELEPHONE
EAccess telephone menu
in the instrument panelAccess telephone menu in the instrument panelAccess telephone menuin the instrument panelAccess telephone menu in the instrument panel
Accept incoming call (press brief- ly)
Access telephone menu in the in- strument panel
Reject incoming call (press and hold down)
End ongoing call/establish call (press briefly)
Switch to private mode (press and hold down)
Redial last number (press and hold down) a)
F
Activation of voice recog-
nition for mobile tele-
phone connected to the
system (if the telephone has this function)*Activation of voice recogni-tion for mobile telephone
connected to the system (if the telephone has this function)*Activation of voice recog-nition for mobile tele-
phone connected to the
system (if the telephone has this function)*Activation of voice recogni-tion for mobile telephone
connected to the system (if the telephone has this function)*Activation of voice recognition
for mobile telephone connected to the system (if the telephone has this function)*
GNext preset b)Next trackb)No function specifiedOperates on instrument
panelOperates on instrument panel/No function specified
HPrevious preset b)Previous trackb)No function specifiedOperates on instrument
panelOperates on instrument panel/No function specified
IChange menu on instru- ment panelChange menu on instru- ment panelChange menu on instru-ment panelChange menu on instru- ment panelChange menu on instrument panel
JChange menu on instru-ment panelChange menu on instru- ment panelChange menu on instru-ment panelChange menu on instru- ment panelChange menu on instrument panel
KOperates on instrumentpanelOperates on instrumentpanelOperates on instrument panelOperates on instrumentpanelOperates on instrument panel/No function specified
LOperates on instrument panelOperates on instrumentpanelOperates on instrument panelOperates on instrumentpanelOperates on instrument panel/No function specified
a)For a more detailed description of how to use this button, please refer to the Radio navigation System User Handbook (SEAT Media System 2.2)
b) Only if the panel is in Audio menu. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

84Opening and closing
If the Safe lock is out of service, the control lamp on the driver door will
flash quickly for 2 seconds before switching off for 30 seconds and then
flashing at a slower rate.
The Safe lock is re-activated on unlocking and locking the vehicle again.
If the vehicle is locked and the Safe lock is deactivated, the vehicle can be
opened from inside by pulling on the door handle.
WARNING
Do not leave people or animals in locked vehicles with the Safe lock acti-
vated: the doors and windows cannot then be opened from the inside.
Doors locked in this manner could delay assistance in an emergency.
Risk of death!
Note
● The anti-theft alarm switches on automatically when the vehicle is
locked, even if the Safe lock is deactivated. The Vehicle interior monitoring,
however, is not activated.
● Given that the Safe function will be activated on locking the vehicle,
CHECK DEADLOCK will be shown on the general instrument panel display. On
vehicles equipped with an informative display, Caution SAFE! On-board docu-
mentation! will be indicated. Unlocking the vehicle with the key
Fig. 46 Key positions
during vehicle locking
and unlocking
– Turn the key in the driver door in the forward driving direction to
its unlock position A
⇒ Fig. 46.
– Pull the handle and open the door.
● All doors (driver door only on vehicles with anti-theft alarm) are un-
locked.
● The rear lid is unlocked.
● The courtesy lights switch on.
● The Safe lock is deactivated.
● The driver door warning lamp stops flashing (on vehicles not equipped
with an anti-theft system) ⇒ page 88.
Note
If the vehicle is equipped with an anti-theft alarm system, you have 15 sec-
onds as of opening the door to insert the key in the ignition and start the
vehicle. If, during these 15 seconds, the vehicle is not started , the alarm is
triggered. 

91
Opening and closing
Opening the rear lid
– Pull on the release lever and lift the rear lid ⇒ Fig. 51. The rear
lid will automatically open.
Closing the rear lid
– Hold the rear lid by one of the two handles on the interior lining
and close it, pushing slightly.
This system may or may not be operative, depending on the situation of the
vehicle.
If the rear lid is locked then it cannot be opened, however if it is unlocked
then the opening system is operative and the rear lid may be opened.
To lock/unlock, press the 
button or button
1 on the remote control key.
A warning appears on the instrument panel display if the rear lid is open or
not properly closed.* An audible warning is also given if the rear lid opens
while the vehicle is moving faster than 6 km/h (4 mph).*
WARNING
● Always close the rear lid properly. Risk of accident or injury.
● The rear lid must not be opened when the reverse or rear fog lights
are lit. This may damage the tail lights.
● Do not close the rear lid by pushing it down with your hand on the
rear window. The glass could smash. Risk of injury!
● Ensure the rear lid is locked after closing it. If not, it may open unex-
pectedly while driving.
WARNING (Continued)
● Never allow children to play in or around the vehicle. A locked vehicle
can be subjected to extremely high and low temperatures, depending on
the time of year, thus causing serious injuries/illness. It could even have
fatal consequences. Close and lock both the rear lid and all the other
doors when you are not using the vehicle.
● Closing the rear lid without observing and ensuring it is clear could
cause serious injury to you and to third parties. Make sure that no one is
ever in the closing path of the rear lid.
● Never drive with the rear lid open or half-closed, as exhaust gases
can be drawn into the interior. Risk of intoxication!
● If you open the rear lid only, do not leave the key inside. The vehicle
cannot be opened if the key is left inside.

Manual release of the rear lid
Fig. 53 Manual release
of the rear lid
In the event of a fault in the central locking system, the rear lid can
be released manually. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

94Lights and visibility
Lights and visibility
Lights Introduction
The location of the controls of right-hand drive cars differs slightly from the
location shown here ⇒ Fig. 55 ⇒  page 94. However, the symbols indicat-
ing the respective positions of the controls remain the same.
WARNING
Never drive with only the side lights on! The side lights are not bright
enough to illuminate the road ahead and to ensure that other road users
are able to see you. Always use your dipped beam headlights if it is dark
or if visibility is poor.
CAUTION
● Use the lights in line with local law.
● However, drivers always remain responsible for correctly adjusting and
using the lights.
Note
● An audible warning will be heard when the light control is set to  and
you remove the ignition key and open the door. Once the driver door is
closed (ignition off), the audible warning will stop, whereas the side lights
will remain on to light up the stationary vehicle if necessary.
● Depending on weather conditions (cold or wet), the lights may mist up
temporarily on the inside. This is particularly the case in the event of a dif-
ference in temperature between the inside and in front of the light. By
switching on the lights, the area through which the beam of light is projec- ted will quickly be demisted, although the edges may remain misted. The
real lights and turn signals can mist up. This has no influence on the useful
life of the lighting system.

Switching lights on and off
Fig. 55 Instrument panel: Light switch/Fuses: Switch for daytime driving lights
Switching on side lights
– Turn the light switch ⇒ Fig. 55  to position .
Switching on dipped beam
– Turn the light switch ⇒ Fig. 55  to position  .
Switching off lights (except daytime driving lights)
– Turn the light switch ⇒ Fig. 55  to position 0. 

95
Lights and visibility
DAY LIGHT Function*
Switching on daytime driving lights
Turn the light switch ⇒ Fig. 55  ⇒ page 94 to position 0.
Switching off daytime driving lights
– Remove the fuse cover on the dash panel ⇒ page 211, Fuses in
the dash panel.
– Press the ⇒ Fig. 55  button ⇒ page 94 to the right.
Switching on daytime driving lights
– Remove the fuse cover on the dash panel ⇒ page 211, Fuses in
the dash panel.
– Press the ⇒ Fig. 55  button ⇒ page 94 to the left.
Switching off daytime driving lights in vehicles with the START-
STOP system
– Switch the ignition off.
– Move the turn signal lever ⇒ Fig. 58 towards the steering wheel,
pressing it down and keeping it in this position.
– Switch on the ignition – wait for the left turn signal to flash 4
times.
– Switch off the ignition – wait until you hear the audible warning
to confirm that the daytime driving lights have been switched
off.
– Release the turn signal lever. Switching on daytime driving lights in vehicles with the START-
STOP system
–
Switch the ignition off.
– Move the turn signal lever ⇒ Fig. 58 towards the steering wheel,
pressing it up and keeping it in this position.
– Switch on the ignition – wait for the right turn signal to flash 4
times.
– Switch off the ignition – wait until you hear the audible warning
to confirm that the daytime driving lights have been switched
on.
– Release the turn signal lever.
Note
The daytime driving lights work when the ignition is switched on. 
Front fog lights
Fig. 56 Instrument pan-
el: light switch 
Safety FirstOperating instructionsPractical TipsTechnical specifications

96Lights and visibility
Switching on front fog lights
–First turn the light switch ⇒ Fig. 56 to position  or .
– Pull on the light switch to position 1
.
The  ⇒ page 65 warning lamp lights up on the general instrument panel if
the front fog lights are switched on. 
Rear fog light
Switching on the rear fog light
– First turn the light switch ⇒ Fig. 56 ⇒ page 95 to position  or
.
– Pull on the light switch to position 2
.
If the vehicle is not equipped with front fog lights ⇒ page 95, the rear fog
light is switched on by turning the switch to position  and pulling it to po-
sition 2
. This type of switch only has one position.
The  ⇒  page 65 warning lamp lights up on the general instrument panel if
the front fog lights are switched on.
If you are towing a trailer or caravan equipped with a rear fog light on a vehi-
cle with a factory-fitted towing bracket or one installed using parts from the
original SEAT parts catalogue , only the rear fog light on the trailer or cara-
van will light up. Range control of main lights

Fig. 57 Instrument pan-
el: light range control
– Turn the control ⇒ Fig. 57 to set the lights to the required set-
ting.
Positions
The control positions roughly correspond to the following vehicle load con-
ditions. Two front occupants, luggage compartment empty.
All seats occupied, luggage compartment empty.
All seats occupied, luggage compartment fully loaded.
Driver only, luggage compartment fully loaded.
CAUTION
Always adjust the range of the lights so that:
● Your vehicle does not dazzle others, particularly oncoming traffic
● The range of the headlights is sufficient for safe driving 
-
123

97
Lights and visibility
Note
Make sure you set the range of the main lights when the dipped beam
headlights are switched on. 
Turn signal and main beam lever
Fig. 58 Turn signal and
main beam headlight lev-
er
The turn signal and main beam headlight lever also operates the
parking lights and the headlight flasher.
Right and left-hand  turn signal 
– Move the lever ⇒ Fig. 58 up A
or down B.
– In order for the turn signals to flash three times (turn signal to
change lanes), move the lever briefly up or down just as far as
point of resistance and then release it.
– Keep the lever held down at the point of resistance for the turn
signals to flash for as long as you hold the lever, e.g. when
changing lanes. Mean beams

– Switch on the dipped beam ⇒ page 94.
– Press the lever ⇒ Fig. 58 forwards in the direction indicated by
arrow C
.
– Pull the lever back to its original position in the direction indica-
ted by arrow D
to switch the main beam off.
Headlight flasher 
– Pull the lever ⇒ Fig. 58 towards the steering wheel (point of re-
sistance) in the direction indicated by arrow D
.
Parking lights 
Instructions for use ⇒ page 98.
CAUTION
Never use the main beam headlights or the headlight flasher if they could
dazzle other drivers.
Note
● The turn signals only work when the ignition is switched on. The corre-
sponding warning lamp  or  flashes in the general instrument panel.
● The turn signals switch off automatically when the steering wheel is re-
turned to the straight-ahead position.
● If a turn signal bulb is defective, the control lamp flashes at double
speed. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

98Lights and visibility
Parking lights*
Parking lights 
– Switch the ignition off.
– Move the turn signal lever ⇒ Fig. 58 ⇒ page 97 up or down to
turn on the right or left-hand parking lights respectively.
Parking light on both sides
– Turn the light switch ⇒ Fig. 55  ⇒ page 94 to position  and
engage the steering lock.
Note
● The parking lights  only work when the ignition is switched on.
● The parking light will not come on automatically on switching the igni-
tion off if the left or right-hand turn signal is left on. 
Front fog lights with CORNER function*
Front fog lights with CORNER function provide better lighting of the area
around the car when driving through a corner or parking, etc.
Front fog lights with CORNER function switch on depending on how far you
turn the steering wheel or whether or not the turn signals 1)
are switched on,
if the following conditions are met:
● The vehicle is stationary, the ignition is switched on or you are moving
at a speed less than 40 km/h (25 mph)
● The daytime driving light is switched off ●
The dipped beam is switched on
● The fog lights are switched off
● Reverse gear is not engaged 
Hazard warning light switch
Fig. 59 Instrument pan-
el: switch for hazard
warning lights
– Press the button  ⇒ Fig. 59 to switch the hazard warning
lights on or off.
The warning lamps on the instrument panel and the warning lamp in the
switch will flash at the same time as the turn signals when the hazard warn-
ing lights are switched on. The hazard warning lights also work when the
ignition is switched off.
The hazard warning lights come on automatically in the event of an accident
in which an airbag is triggered. 
1)
In the event of a conflict between both functions, i.e. if you turn the steering wheel to the
left while the right-hand turn signal is on, the turn signals will take priority.

120Seats and storage
Storage compartment
Summary
The following storage areas are available in the vehicle:
Passenger side glove compartment⇒ page 120Compartment for reflective vest⇒ page 121Storage compartments in front seats⇒ page 121Net pockets on back of front backrests⇒ page 122Storage compartment for (sun)glasses⇒ page 122Storage compartments in centre console⇒ page 123Multimedia compartment⇒ page 123Storage compartments in doors⇒ page 123Storage compartment in luggage compartment⇒ page 124
WARNING
● Never place any objects on the instrument panel. These objects could
be flown around the interior while the vehicle is moving (on accelerating
or turning) and distract you. Risk of accident!
● Make sure objects remain in the centre console or other compart-
ments while the vehicle is moving. Otherwise, this would prevent you
from braking, changing gear or accelerating. Risk of accident!
 Passenger side glove compartment
Fig. 88 Instrument pan-
el: passenger side glove
compartment
Fig. 89 Storage: cooling
control
Opening and closing passenger side glove compartment
– Pull the catch on the lid in the direction indicated by the arrow
⇒ 
Fig. 88 and open the lid.
– Close the lid and push it until it engages.
Storage compartment lighting
– The light will come on automatically when the glove compart-
ment is opened. 

141
Driving
The warning lamp lights up when the handbrake is applied with the ignition
on  . 
Stability system (ESC)
Fig. 104 ESC system:
ASR switch
The ESC system increases control of the vehicle in emergency situations,
e.g. during a sudden change in direction. Depending on the driving condi-
tions, it reduces the risk of skidding and increases driving stability.
The system uses the steering wheel angle and road speed to calculate the
changes of direction desired by the driver, and constantly compares them
with the actual behaviour of the vehicle. When irregularities occur, for exam-
ple, if the vehicle begins to skid, the ESC brakes the appropriate wheel au-
tomatically.
The  warning lamp in the general instrument panel starts flashing when
the system is working.
The stability (ESC) system includes the following systems:
● Anti-lock brake system (ABS)
● Traction control system (ASR)
● Electronic differential lock (EDL) ●
Brake assist system (HBA)
● Hill hold control (HHC)
The ESC system cannot be switched on. The 
⇒ Fig. 104 button can only
be used to switch off the ASR system. The  warning lamp lights up on the
general instrument panel if the ASR system is switched off.
The ASR should be switched on at all times. Only under certain circumstan-
ces should the system be switched off, e.g.
● Driving with chains
● Driving in deep snow or on very soft surfaces
● During the “swinging movement” required to remove a stuck vehicle
Switch the ASR back on as soon as possible.
Brake assist system (HBA)*
The HBA system is activated when you press down on the brake pedal sud-
denly. It increases braking power, helping to reduce braking distances. To
reduce the braking distance as much as possible, keep the brake pedal
pressed down firmly until the vehicle comes to a standstill.
With the help of this system, the ABS is activated more quickly and more
efficiently.
The brake assist function is deactivated automatically when the brake pedal
is released.
Hill hold control (HHC)*
The HHC system makes it easier to start the vehicle on hills. The system
maintains the brake pressure created by pressing down on the brake pedal
for 2 seconds after it has been released. Your foot can be removed from the
brake pedal and you can use the accelerator pedal and move away on a hill
without having to use the handbrake. The brake pressure drops as the ac-
celerator pedal is pressed. If the vehicle is not started then it will start to
move backwards after two seconds. 
Safety FirstOperating instructionsPractical TipsTechnical specifications